| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
CONFIG_NFSD_V3 has been removed. NFSD support for NFSv3 can no
longer be disabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
Remove references to symbols that no longer exist as reported by
scripts/checkkconfigsymbols.py.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200724131728.1643966-2-mpe@ellerman.id.au
|
|
Regenerate defconfigs to remove CONFIG_CMDLINE_BOOL and the default
CONFIG_CMDLINE where applicable.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200611224220.25066-3-chris.packham@alliedtelesis.co.nz
|
|
Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a5714 ("driver: base: Disable
CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
made default to 'n',
2. It is not recommended (help message: "This should not be used today
[...] creates a high system load") and was kept only for ancient
userland,
3. Certain userland specifically requests it to be disabled (systemd
README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In commit a85406afeb3e ("netfilter: conntrack: built-in support for
SCTP"), NF_CT_PROTO_SCTP switched from tristate to bool and became
default y. Similarly in commit 9b91c96c5d1f ("netfilter: conntrack:
built-in support for UDPlite"), NF_CT_PROTO_UDPLITE switched from
tristate to bool and became default y.
We had a few configs which set them to =m, which is no longer valid.
We don't need to change them to =y because both symbols are default y
and are enabled automatically based on the other symbols in the
affected defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In commit 73d8ef76006b ("Input: mousedev - stop offering PS/2 to userspace by
default") (Jan 2017), CONFIG_INPUT_MOUSEDEV was switched from default y to
default n, with the explanation:
Evdev interface has been available for many years and by now everyone
is switched to using it, so let's stop offering /dev/input/mouseN
and /dev/psaux by default.
We had a number of configs which had it enabled, but going by the above
explanation probably don't need it enabled anymore.
So drop the last remnants of it from our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Since commit 401e4238f35c ("crypto: rng - Make DRBG the default RNG") we no longer need to set CONFIG_CRYPTO_ANSI_CPRNG in our defconfigs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Update defconfigs to remove old symbols and comments referencing old
symbols.
Dropped:
* AVERAGE
* INET_LRO
* EXT3_DEFAULTS_TO_ORDERED
* EXT3_FS_XATTR
* I2O
* INFINIBAND_AMSO1100
* INFINIBAND_EHCA
* IP1000
Replaced:
* BLK_DEV_XIP -> BLK_DEV_RAM_DAX
* CLK_PPC_CORENET -> CLK_QORIQ
* EXT2_FS_XIP -> FS_DAX
* EXT3_FS* -> EXT4_FS*
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
It looks like it's ~4 years since we updated some of these, so do a bulk
update.
Verified that the before and after generated configs are exactly the
same.
Which begs the question why update them? The answer is that it can be
confusing when the stored defconfig drifts too far from the generated
result.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add support for the Motorola/Emerson MVME5100 Single Board Computer.
The MVME5100 is a 6U form factor VME64 computer with:
- A single MPC7410 or MPC750 CPU
- A HAWK Processor Host Bridge (CPU to PCI) and
MultiProcessor Interrupt Controller (MPIC)
- Up to 500Mb of onboard memory
- A M48T37 Real Time Clock (RTC) and Non-Volatile Memory chip
- Two 16550 compatible UARTS
- Two Intel E100 Fast Ethernets
- Two PCI Mezzanine Card (PMC) Slots
- PPCBug Firmware
The HAWK PHB/MPIC is compatible with the MPC10x devices.
There is no onboard disk support. This is usually provided by installing a PMC
in first PMC slot.
This patch revives the board support, it was present in early 2.6
series kernels. The board support in those days was by Matt Porter of
MontaVista Software.
CSC Australia has around 31 of these boards in service. The kernel in use
for the boards is based on 2.6.31. The boards are operated without disks
from a file server.
This patch is based on linux-3.13-rc2 and has been boot tested.
Only boards with 512 Mb of memory are known to work.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Tested-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
Chuck Lever
Michael Ellerman
Chris Packham
Krzysztof Kozlowski
Andrew Donnellan
Stephen Chivers