| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The Power ISA 2.06 spec introduces a standard MMU programming model that
is based on the Freescale Book-E MMU programing model. The Freescale
version is pretty backwards compatiable with the ISA 2.06 definition so
we are starting to refactor some of the Freescale code so it can be
easily shared.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The Power ISA 2.06 added power of two page sizes to the embedded MMU
architecture. Its done it such a way to be code compatiable with the
existing HW. Made the minor code changes to support both power of two
and power of four page sizes. Also added some new MAS bits and macros
that are defined as part of the 2.06 ISA. Renamed some things to use
the 'Book-3e' concept to convey the new MMU that is based on the
Freescale Book-E MMU programming model.
Note, its still invalid to try and use a page size that isn't supported
by cpu.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This reworks the context management code used by 4xx,8xx and
freescale BookE. It adds support for SMP by implementing a
concept of stale context map to lazily flush the TLB on
processors where a context may have been invalidated. This
also contains the ground work for generalizing such lazy TLB
flushing by just picking up a new PID and marking the old one
stale. This will be implemented later.
This is a first implementation that uses a global spinlock.
Ideally, we should try to get at least the fast path (context ID
already assigned) lockless or limited to a per context lock,
but for now this will do.
I tried to keep the UP case reasonably simple to avoid adding
too much overhead to 8xx which does a lot of context stealing
since it effectively has only 16 PIDs available.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The initial TLB mapping for the kernel boot didn't set the memory coherent
attribute, MAS2[M], in SMP mode.
If this code supported booting a secondary processor, which it doesn't yet,
but if it did, then when a secondary processor boots, it would probably signal
the primary processor by setting a variable called something like
__secondary_hold_acknowledge. However, due to the lack of the M bit, the
primary processor would not snoop the transaction (even if a transaction were
broadcast). If primary CPU's L1 D-cache had a copy, it would not be flushed
and the CPU would never see the ack. Which would have resulted in the primary
CPU spinning for a long time, perhaps a full second before it gives up, while
it would have waited for the ack from the secondary CPU that it wouldn't have
been able to see because of the stale cache.
The value of MAS2 for the boot page TLB1 entry is a compile time constant,
so there is no need to calculate it in powerpc assembly language.
Also, from the MPC8572 manual section 6.12.5.3, "Bits that represent
offsets within a page are ignored and should be cleared." Existing code
didn't clear them, this code does.
The same when the page of KERNELBASE is found; we don't need to use asm to
mask the lower 12 bits off.
In the code that computes the address to rfi from, don't hard code the
offset to 24 bytes, but have the assembler figure that out for us.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
Kumar Gala
Benjamin Herrenschmidt
Trent Piepho
Stephen Rothwell