| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
CONFIG_VIRT_CPU_ACCOUNTING_GEN under pseries does not provide stolen
time accounting unless CONFIG_PARAVIRT_TIME_ACCOUNTING is enabled.
Implement this using the VPA accumulated wait counters.
Note this will not work on current KVM hosts because KVM does not
implement the VPA dispatch counters (yet). It could be implemented
with the dispatch trace log as it is for VIRT_CPU_ACCOUNTING_NATIVE,
but that is not necessary for the more limited accounting provided
by PARAVIRT_TIME_ACCOUNTING, and it is more expensive, complex, and
has downsides like potential log wrap.
From Shrikanth:
[...] it was tested on Power10 [PowerVM] Shared LPAR. system has two
LPAR. we will call first one LPAR1 and second one as LPAR2. Test was
carried out in SMT=1. Similar observation was seen in SMT=8 as well.
LPAR config header from each LPAR is below. LPAR1 is twice as big as
LPAR2. Since Both are sharing the same underlying hardware, work
stealing will happen when both the LPAR's are contending for the same
resource.
LPAR1:
type=Shared mode=Uncapped smt=Off lcpu=40 cpus=40 ent=20.00
LPAR2:
type=Shared mode=Uncapped smt=Off lcpu=20 cpus=40 ent=10.00
mpstat was used to check for the utilization. stress-ng has been used
as the workload. Few cases are tested. when the both LPAR are idle
there is no steal time. when LPAR1 starts running at 100% which
consumes all of the physical resource, steal time starts to get
accounted. With LPAR1 running at 100% and LPAR2 starts running, steal
time starts increasing. This is as expected. When the LPAR2 Load is
increased further, steal time increases further.
Case 1: 0% LPAR1; 0% LPAR2
%usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
0.00 0.00 0.05 0.00 0.00 0.00 0.00 0.00 0.00 99.95
Case 2: 100% LPAR1; 0% LPAR2
%usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
97.68 0.00 0.00 0.00 0.00 0.00 2.32 0.00 0.00 0.00
Case 3: 100% LPAR1; 50% LPAR2
%usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
86.34 0.00 0.10 0.00 0.00 0.03 13.54 0.00 0.00 0.00
Case 4: 100% LPAR1; 100% LPAR2
%usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
78.54 0.00 0.07 0.00 0.00 0.02 21.36 0.00 0.00 0.00
Case 5: 50% LPAR1; 100% LPAR2
%usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
49.37 0.00 0.00 0.00 0.00 0.00 1.17 0.00 0.00 49.47
Patch is accounting for the steal time and basic tests are holding
good.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Shrikanth Hegde <sshegde@linux.ibm.com>
[mpe: Add SPDX tag to new paravirt_api_clock.h]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220902085316.2071519-3-npiggin@gmail.com
|
|
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
|
|
PowerVM provides an isolated Platform Keystore(PKS) storage allocation
for each LPAR with individually managed access controls to store
sensitive information securely. It provides a new set of hypervisor
calls for Linux kernel to access PKS storage.
Define POWER LPAR Platform KeyStore(PLPKS) driver using H_CALL interface
to access PKS storage.
Signed-off-by: Nayna Jain <nayna@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220723113048.521744-2-nayna@linux.ibm.com
|
|
When RDRAND was introduced, there was much discussion on whether it
should be trusted and how the kernel should handle that. Initially, two
mechanisms cropped up, CONFIG_ARCH_RANDOM, a compile time switch, and
"nordrand", a boot-time switch.
Later the thinking evolved. With a properly designed RNG, using RDRAND
values alone won't harm anything, even if the outputs are malicious.
Rather, the issue is whether those values are being *trusted* to be good
or not. And so a new set of options were introduced as the real
ones that people use -- CONFIG_RANDOM_TRUST_CPU and "random.trust_cpu".
With these options, RDRAND is used, but it's not always credited. So in
the worst case, it does nothing, and in the best case, maybe it helps.
Along the way, CONFIG_ARCH_RANDOM's meaning got sort of pulled into the
center and became something certain platforms force-select.
The old options don't really help with much, and it's a bit odd to have
special handling for these instructions when the kernel can deal fine
with the existence or untrusted existence or broken existence or
non-existence of that CPU capability.
Simplify the situation by removing CONFIG_ARCH_RANDOM and using the
ordinary asm-generic fallback pattern instead, keeping the two options
that are actually used. For now it leaves "nordrand" for now, as the
removal of that will take a different route.
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The pseries platform does not use the native hash code but the PAPR
virtualised hash interfaces, so remove PPC_HASH_MMU_NATIVE.
This requires moving tlbiel code from hash_native.c to hash_utils.c.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211201144153.2456614-4-npiggin@gmail.com
|
|
PPC_NATIVE now only controls the native HPT code, so rename it to be
more descriptive. Restrict it to Book3S only.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211201144153.2456614-3-npiggin@gmail.com
|
|
Remove the pseries scanlog driver.
This code supports functions from Power4-era servers that are not present
on targets currently supported by arch/powerpc. System manuals from this
time have this description:
Scan Dump data is a set of chip data that the service processor gathers
after a system malfunction. It consists of chip scan rings, chip trace
arrays, and Scan COM (SCOM) registers. This data is stored in the
scan-log partition of the system’s Nonvolatile Random Access
Memory (NVRAM).
PowerVM partition firmware development doesn't recognize the associated
function call or property, and they don't see any references to them in
their codebase. It seems to have been specific to non-virtualized pseries.
References:
Historical Linux commit from February 2003 (interesting to note this seems
to be the source of non-GPL exports for rtas_call etc):
https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/?id=f92e361842d5251e50562b09664082dcbd0548bb
IntelliStation and pSeries docs which refer to the feature:
http://ps-2.retropc.se/basil.holloway/ALL%20PDF/380635.pdf
http://ps-2.kev009.com/rs6000/manuals/p/p615-6C3-6E3/6C3_and_6E3_Users_Guide_SA38-0629.pdf
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210920173203.1800475-1-nathanl@linux.ibm.com
|
|
Introduce a powerpc version of the cc_platform_has() function. This will
be used to replace the powerpc mem_encrypt_active() implementation, so
the implementation will initially only support the CC_ATTR_MEM_ENCRYPT
attribute.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lkml.kernel.org/r/20210928191009.32551-5-bp@alien8.de
|
|
This implements the generic paravirt qspinlocks using H_PROD and
H_CONFER to kick and wait.
This uses an un-directed yield to any CPU rather than the directed
yield to a pre-empted lock holder that paravirtualised simple
spinlocks use, that requires no kick hcall. This is something that
could be investigated and improved in future.
Performance results can be found in the commit which added queued
spinlocks.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200724131423.1362108-5-npiggin@gmail.com
|
|
Commit d4e58e5928f8 ("powerpc/powernv: Enable POWER8 doorbell IPIs")
added a select of PPC_DOORBELL to PPC_PSERIES, but it already had a
select of PPC_DOORBELL. One is enough.
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191219125840.32592-1-mpe@ellerman.id.au
|
|
We can now get rid of the cmm_lock and completely rely on the balloon
compaction internals, which now also manage the page list and the
lock.
Inflated/"loaned" pages are now movable. Memory blocks that contain
such pages can get offlined. Also, all such pages will be marked
PageOffline() and can therefore be excluded in memory dumps using
recent versions of makedumpfile.
Don't switch to balloon_page_alloc() yet (due to the GFP_NOIO). Will
do that separately to discuss this change in detail.
Signed-off-by: David Hildenbrand <david@redhat.com>
[mpe: Add isolated_pages-- in cmm_migratepage() as suggested by David]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191031142933.10779-9-david@redhat.com
|
|
SWIOTLB checks range of incoming CPU addresses to be bounced and sees if
the device can access it through its DMA window without requiring bouncing.
In such cases it just chooses to skip bouncing. But for cases like secure
guests on powerpc platform all addresses need to be bounced into the shared
pool of memory because the host cannot access it otherwise. Hence the need
to do the bouncing is not related to device's DMA window and use of bounce
buffers is forced by setting swiotlb_force.
Also, connect the shared memory conversion functions into the
ARCH_HAS_MEM_ENCRYPT hooks and call swiotlb_update_mem_attributes() to
convert SWIOTLB's memory pool to shared memory.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[ bauerman: Use ARCH_HAS_MEM_ENCRYPT hooks to share swiotlb memory pool. ]
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820021326.6884-15-bauerman@linux.ibm.com
|
|
Introduce CONFIG_PPC_SVM to control support for secure guests and include
Ultravisor-related helpers when it is selected
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820021326.6884-3-bauerman@linux.ibm.com
|
|
Formatting of Kconfig files doesn't look so pretty, so let the
Great White Handkerchief come around and clean it up.
Also convert "---help---" as requested.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
So far the pseries platforms has always been using IOMMU making
SWIOTLB unnecessary. Now we want secure guests which means devices can
only access certain areas of guest physical memory; we are going to
use SWIOTLB for this purpose.
This allows SWIOTLB for pseries. By default there is no change in
behavior.
This enables SWIOTLB when the "swiotlb" kernel parameter is set to
"force".
With the SWIOTLB enabled, the kernel creates a directly mapped DMA
window (using the usual DDW mechanism) and implements SWIOTLB on top
of that.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Pull Kconfig file consolidation from Masahiro Yamada:
"Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries by
Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right
Kconfig files. This series instead just selects the presence (when
needed) and then handles everything in the bus-specific Kconfig file
under drivers/"
* tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
pcmcia: remove per-arch PCMCIA config entry
eisa: consolidate EISA Kconfig entry in drivers/eisa
rapidio: consolidate RAPIDIO config entry in drivers/rapidio
pcmcia: allow PCMCIA support independent of the architecture
PCI: consolidate the PCI_SYSCALL symbol
PCI: consolidate the PCI_DOMAINS and PCI_DOMAINS_GENERIC config options
PCI: consolidate PCI config entry in drivers/pci
MIPS: remove the HT_PCI config option
|
|
Making PAPR_SCM select LIBNVDIMM results in circular dependencies in
Kconfig when another symbol depends on it. Fix this by replacing the
select with a depends.
Fixes: b5beae5e224f ("powerpc/pseries: Add driver for PAPR SCM regions")
Reported-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Adds a driver that implements support for enabling and accessing PAPR
SCM regions. Unfortunately due to how the PAPR interface works we can't
use the existing of_pmem driver (yet) because:
a) The guest is required to use the H_SCM_BIND_MEM h-call to add
add the SCM region to it's physical address space, and
b) There is currently no mechanism for relating a bare of_pmem region
to the backing DIMM (or not-a-DIMM for our case).
Both of these are easily handled by rolling the functionality into a
seperate driver so here we are...
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c29 ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the framework for using XIVE in a PowerVM guest. The support
is very similar to the native one in a much simpler form.
Each source is associated with an Event State Buffer (ESB). This is a
two bit state machine which is used to trigger events. The bits are
named "P" (pending) and "Q" (queued) and can be controlled by MMIO.
The Guest OS registers event (or notifications) queues on which the HW
will post event data for a target to notify.
Instead of OPAL calls, a set of Hypervisors call are used to configure
the interrupt sources and the event/notification queues of the guest:
- H_INT_GET_SOURCE_INFO
used to obtain the address of the MMIO page of the Event State
Buffer (PQ bits) entry associated with the source.
- H_INT_SET_SOURCE_CONFIG
assigns a source to a "target".
- H_INT_GET_SOURCE_CONFIG
determines to which "target" and "priority" is assigned to a source
- H_INT_GET_QUEUE_INFO
returns the address of the notification management page associated
with the specified "target" and "priority".
- H_INT_SET_QUEUE_CONFIG
sets or resets the event queue for a given "target" and "priority".
It is also used to set the notification config associated with the
queue, only unconditional notification for the moment. Reset is
performed with a queue size of 0 and queueing is disabled in that
case.
- H_INT_GET_QUEUE_CONFIG
returns the queue settings for a given "target" and "priority".
- H_INT_RESET
resets all of the partition's interrupt exploitation structures to
their initial state, losing all configuration set via the hcalls
H_INT_SET_SOURCE_CONFIG and H_INT_SET_QUEUE_CONFIG.
- H_INT_SYNC
issue a synchronisation on a source to make sure sure all
notifications have reached their queue.
As for XICS, the XIVE interface for the guest is described in the
device tree under the "interrupt-controller" node. A couple of new
properties are specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), also called rings, for the User level and
for the Guest OS level. Only the Guest OS level is taken into
account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the interrupt numbers ranges assigned to the guest. These are
allocated using a simple bitmap.
and also :
- "/ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use.
Tested with a QEMU XIVE model for pseries and with the Power hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
POWER9 introduces a new version of the hypervisor API to access the 24x7
perf counters. The new version changed some of the structures used for
requests and results.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The pseries platform supports Power4 and later CPUs, all of which are
multithreaded and/or multicore.
In practice no one ever builds a SMP=n kernel for these machines. So as
we did for powernv, have the pseries platform imply SMP=y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We added support for HAVE_CONTEXT_TRACKING, but placed the option inside
PPC_PSERIES.
This has the undesirable effect that NO_HZ_FULL can be enabled on a
kernel with both powernv and pseries support, but cannot on a kernel
with powernv only support.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The IBMEBUS code supports the GX bus found on Power7 and earlier CPUs.
On Power8 it has been replaced, and so we have no need for it.
We don't actually have a config symbol for Power8 vs Power7 etc., but
we only support booting little endian on Power8 or later, so use that as
a reasonable approximation.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
ibmebus.c is pseries only code, so move it in there.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
vio.c is pseries only code, so move it in there.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Now that pseries selects PCI_MSI && PCI, EEH will always be true, and
therefore CONFIG_PSERIES_MSI will always be true. So drop it, and move
msi.o to obj-y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The pseries build with PCI=n looks to have been broken for at least 5
years, and no one's noticed or cared.
Following the obvious breakages backward, the first commit I can find
that builds is the parent of 2eb4afb69ff3 ("powerpc/pci: Move pseries
code into pseries platform specific area") from April 2009.
A distro would never ship a PCI=n kernel, so it is only useful for folks
building custom kernels. Also on KVM the virtio devices appear on PCI,
so it would only be useful if you were building kernels specifically to
run on PowerVM and with no PCI devices.
The added code complexity, and testing load (which we've clearly not
been doing), is not justified by the small reduction in kernel size for
such a niche use case.
So just make PCI non-optional on pseries.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
With minor checks, we can move most of the code for nvram
under pseries to a common place to be re-used by other
powerpc platforms like powernv. This patch moves such
common code to arch/powerpc/kernel/nvram_64.c file.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Move select of ZLIB_DEFLATE to PPC64 to fix the build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Moving config DTL up so it is below config PPC_SPLPAR means that
menuconfig will show config DTL nicely indented right below config
PPC_SPLPAR when PPC_SPLPAR is enabled.
To contrast that, right now if I enable PPC_SPLPAR in menuconfig, all I
can immediately tell is that "something showed up further down the list
where I wasn't looking", and I end up having to toggle the option a few
times to figure out what showed up, or look at the KConfig to find out
that config DTL depends on config PPC_SPLPAR.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch enables POWER8 doorbell IPIs on powernv.
Since doorbells can only IPI within a core, we test to see when we can use
doorbells and if not we fall back to XICS. This also enables hypervisor
doorbells to wakeup us up from nap/sleep via the LPCR PECEDH bit.
Based on tests by Anton, the best case IPI latency between two threads dropped
from 894ns to 512ns.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The commit adds a Kconfig option which allows the hv_gpci and hv_24x7
PMUs, added in the preceeding commits, to be built.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We have a driver for the ARCH_RANDOM hook in rng.c, so we should select
ARCH_RANDOM on pseries.
Without this the build breaks if you turn ARCH_RANDOM off.
This hasn't broken the build because pseries_defconfig doesn't specify a
value for PPC_POWERNV, which is default y, and selects ARCH_RANDOM.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Move the file from arch specific pseries/processor_idle.c
to drivers/cpuidle/cpuidle-pseries.c
Make the relevant Makefile and Kconfig changes.
Also, introduce Kconfig.powerpc in drivers/cpuidle
for all powerpc cpuidle drivers.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Previously PSERIES_MSI depended on PPC_PSERIES via EEH. However in
commit 317f06d "powerpc/eeh: Move common part to kernel directory" we
made CONFIG_EEH selectable on POWERNV. That leaves us with PSERIES_MSI
being live even when PSERIES=n. Fix it by making PSERIES_MSI depend
directly on PPC_PSERIES.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The Kconfig symbol HOTPLUG was removed with commit 40b313608a ("Finally
eradicate CONFIG_HOTPLUG"). But there's still one select statement for
that symbol. It seems that select statement was added after the patch to
remove CONFIG_HOTPLUG was submitted. Anyhow, it is useless and can be
dropped.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The patch moves the common part of EEH core into arch/powerpc/kernel
directory so that we needn't PPC_PSERIES while compiling POWERNV
platform:
* Move the EEH common part into arch/powerpc/kernel
* Move the functions for PCI hotplug from pSeries platform to
arch/powerpc/kernel/pci-hotplug.c
* Move CONFIG_EEH from arch/powerpc/platforms/pseries/Kconfig to
arch/powerpc/platforms/Kconfig
* Adjust makefile accordingly
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Adam Lackorzynski reported the following build failure on
!CONFIG_HOTPLUG_CPU configuration:
CC arch/powerpc/kernel/rtas.o
arch/powerpc/kernel/rtas.c: In function ‘rtas_cpu_state_change_mask’:
arch/powerpc/kernel/rtas.c:843:4: error: implicit declaration of function ‘cpu_down’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/kernel/rtas.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
The build fails because cpu_down() is defined only under CONFIG_HOTPLUG_CPU.
Looking further, the mobility code in pseries is one of the call-sites which
uses rtas_ibm_suspend_me(), which in turn calls rtas_cpu_state_change_mask().
And the mobility code is unconditionally compiled-in (it does not fall under
any Kconfig option). And commit 120496ac (powerpc: Bring all threads online
prior to migration/hibernation) which introduced this build regression is
critical for the proper functioning of the migration code. So it appears
that the only solution to this problem is to enable CONFIG_HOTPLUG_CPU if
SMP is enabled on PPC_PSERIES platforms. So make that change in the Kconfig.
Reported-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Start context tracking support from pSeries.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch actually hooks up doorbell interrupts on POWER8:
- Select the PPC_DOORBELL Kconfig option from PPC_PSERIES
- Add the doorbell CPU feature bit to POWER8
- We define a new pSeries_cause_ipi_mux() function that issues a
doorbell interrupt if the recipient is another thread within the same
core as the sender. If the recipient is in a different core it falls
back to using XICS to deliver the IPI as before.
- During pSeries_smp_probe() at boot, we check if doorbell interrupts
are supported. If they are we set the cause_ipi function pointer to
the above mentioned function, otherwise we leave it as whichever XICS
cause_ipi function was determined by xics_smp_probe().
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
|
|
Recently, Ryan Wang tried to compile PPC pSeries platform without
CONFIG_EEH and eventually run into errors. Nishanth Aravamudan
helped to narrow down the root cause. Actually, the pSeries platform
depends on CONFIG_EEH heavily and that won't work properly without
EEH support.
According to Ben's suggestion, the patch make CONFIG_EEH invisible
and keep it as always selected on pSeries platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Correct spelling typo in various Kconfig file.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
|
|
Pull core device tree changes for Linux v3.4 from Grant Likely:
"This branch contains a minor documentation addition, a utility
function for parsing string properties needed by some of the new ARM
platforms, disables dynamic DT code that isn't used anywhere but on a
few PPC machines, and exports DT node compatible data to userspace via
UEVENT properties. Nothing earth shattering here."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of: Only compile OF_DYNAMIC on PowerPC pseries and iseries
arm/dts: OMAP3: Add omap3evm and am335xevm support
drivercore: Output common devicetree information in uevent
of: Add of_property_match_string() to find index into a string list
|
|
After this, we can remove the legacy iSeries code more easily.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Only two architectures use the OF node reference counting and reclaim bits.
There is no need to compile it for the rest of the PowerPC platforms or for
any of the other architectures. This patch makes iseries and pseries
select CONFIG_OF_DYNAMIC, and makes it default to off for everything else.
It is still safe to turn on CONFIG_OF_DYNAMIC on all architectures, it just
isn't necessary.
v2: Also select OF_DYNAMIC for PPC_CHROMA and MPC885ADS as reported by Michael
Meuling
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jimi Xenidis <jimix@pobox.com> (for PPC_CHROMA bug fix)
Cc: Rob Herring <rob.herring@calxeda.com>
|
|
As pointed out, asm/system.h has empty inline implementations for
update_smt_snooze_delay and pseries_notify_cpuidle_add_cpu, which are
used when CONFIG_PSERIES_IDLE is undefined. Since those two functions
are used in core power architecture functions (store_smt_snooze_delay
at kernel/sysfs.c and smp_xics_setup_cpu at platforms/pseries/smp.c),
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
Nicholas Piggin
Linus Torvalds
Nayna Jain
Jason A. Donenfeld
Nathan Lynch
Tom Lendacky
Michael Ellerman
David Hildenbrand
Anshuman Khandual
Thiago Jung Bauermann
Enrico Weigelt, metux IT consult
Alexey Kardashevskiy
Oliver O'Halloran
Christoph Hellwig
Bartlomiej Zolnierkiewicz
Greg Kroah-Hartman
Cédric Le Goater
Thiago Jung Bauermann
Anton Blanchard
Hari Bathini
Cody P Schafer
Michael Neuling
Deepthi Dharwar
Michael Ellerman
Paul Bolle
Gavin Shan
Srivatsa S. Bhat
Li Zhong
Ian Munsie
Masanari Iida
Stephen Rothwell
Grant Likely