| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Function memcpy_real() is an univeral data mover that does not
require DAT mode to be able reading from a physical address.
Its advantage is an ability to read from any address, even
those for which no kernel virtual mapping exists.
Although memcpy_real() is interrupt-safe, there are no handlers
that make use of this function. The compiler instrumentation
have to be disabled and separate no-DAT stack used to allow
execution of the function once DAT mode is disabled.
Rework memcpy_real() to overcome these shortcomings. As result,
data copying (which is primarily reading out a crashed system
memory by a user process) is executed on a regular stack with
enabled interrupts. Also, use of memcpy_real_buf swap buffer
becomes unnecessary and the swapping is eliminated.
The above is achieved by using a fixed virtual address range
that spans a single page and remaps that page repeatedly when
memcpy_real() is called for a particular physical address.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Temporary unsetting of the prefix page in memcpy_absolute() routine
poses a risk of executing code path with unexpectedly disabled prefix
page. This rework avoids the prefix page uninstalling and disabling
of normal and machine check interrupts when accessing the absolute
zero memory.
Although memcpy_absolute() routine can access the whole memory, it is
only used to update the absolute zero lowcore. This rework therefore
introduces a new mechanism for the absolute zero lowcore access and
scraps memcpy_absolute() routine for good.
Instead, an area is reserved in the virtual memory that is used for
the absolute lowcore access only. That area holds an array of 8KB
virtual mappings - one per CPU. Whenever a CPU is brought online, the
corresponding item is mapped to the real address of the previously
installed prefix page.
The absolute zero lowcore access works like this: a CPU calls the
new primitive get_abs_lowcore() to obtain its 8KB mapping as a
pointer to the struct lowcore. Virtual address references to that
pointer get translated to the real addresses of the prefix page,
which in turn gets swapped with the absolute zero memory addresses
due to prefixing. Once the pointer is not needed it must be released
with put_abs_lowcore() primitive:
struct lowcore *abs_lc;
unsigned long flags;
abs_lc = get_abs_lowcore(&flags);
abs_lc->... = ...;
put_abs_lowcore(abs_lc, flags);
To ensure the described mechanism works large segment- and region-
table entries must be avoided for the 8KB mappings. Failure to do
so results in usage of Region-Frame Absolute Address (RFAA) or
Segment-Frame Absolute Address (SFAA) large page fields. In that
case absolute addresses would be used to address the prefix page
instead of the real ones and the prefixing would get bypassed.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Pull MM updates from Andrew Morton:
"Most of the MM queue. A few things are still pending.
Liam's maple tree rework didn't make it. This has resulted in a few
other minor patch series being held over for next time.
Multi-gen LRU still isn't merged as we were waiting for mapletree to
stabilize. The current plan is to merge MGLRU into -mm soon and to
later reintroduce mapletree, with a view to hopefully getting both
into 6.1-rc1.
Summary:
- The usual batches of cleanups from Baoquan He, Muchun Song, Miaohe
Lin, Yang Shi, Anshuman Khandual and Mike Rapoport
- Some kmemleak fixes from Patrick Wang and Waiman Long
- DAMON updates from SeongJae Park
- memcg debug/visibility work from Roman Gushchin
- vmalloc speedup from Uladzislau Rezki
- more folio conversion work from Matthew Wilcox
- enhancements for coherent device memory mapping from Alex Sierra
- addition of shared pages tracking and CoW support for fsdax, from
Shiyang Ruan
- hugetlb optimizations from Mike Kravetz
- Mel Gorman has contributed some pagealloc changes to improve
latency and realtime behaviour.
- mprotect soft-dirty checking has been improved by Peter Xu
- Many other singleton patches all over the place"
[ XFS merge from hell as per Darrick Wong in
https://lore.kernel.org/all/YshKnxb4VwXycPO8@magnolia/ ]
* tag 'mm-stable-2022-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (282 commits)
tools/testing/selftests/vm/hmm-tests.c: fix build
mm: Kconfig: fix typo
mm: memory-failure: convert to pr_fmt()
mm: use is_zone_movable_page() helper
hugetlbfs: fix inaccurate comment in hugetlbfs_statfs()
hugetlbfs: cleanup some comments in inode.c
hugetlbfs: remove unneeded header file
hugetlbfs: remove unneeded hugetlbfs_ops forward declaration
hugetlbfs: use helper macro SZ_1{K,M}
mm: cleanup is_highmem()
mm/hmm: add a test for cross device private faults
selftests: add soft-dirty into run_vmtests.sh
selftests: soft-dirty: add test for mprotect
mm/mprotect: fix soft-dirty check in can_change_pte_writable()
mm: memcontrol: fix potential oom_lock recursion deadlock
mm/gup.c: fix formatting in check_and_migrate_movable_page()
xfs: fail dax mount if reflink is enabled on a partition
mm/memcontrol.c: remove the redundant updating of stats_flush_threshold
userfaultfd: don't fail on unrecognized features
hugetlb_cgroup: fix wrong hugetlb cgroup numa stat
...
|
|
When ptep_get_and_clear_full is called for a mm teardown, we will now
attempt to destroy the secure pages. This will be faster than export.
In case it was not a teardown, or if for some reason the destroy page
UVC failed, we try with an export page, like before.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Nico Boehr <nrb@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-11-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-11-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
|
|
This enables ARCH_HAS_VM_GET_PAGE_PROT on the platform and exports
standard vm_get_page_prot() implementation via DECLARE_VM_GET_PAGE_PROT,
which looks up a private and static protection_map[] array. Subsequently
all __SXXX and __PXXX macros can be dropped which are no longer needed.
Link: https://lkml.kernel.org/r/20220711070600.2378316-19-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Brian Cain <bcain@quicinc.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guo Ren <guoren@kernel.org>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Use the new protected_count field as a counter instead of the old
is_protected flag. This will be used in upcoming patches.
Increment the counter when a secure configuration is created, and
decrement it when it is destroyed. Previously the flag was set when the
set secure parameters UVC was performed.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-6-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-6-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
|
|
Let's use bit 52, which is unused.
Link: https://lkml.kernel.org/r/20220329164329.208407-7-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Don Dutile <ddutile@redhat.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jann Horn <jannh@google.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Liang Zhang <zhangliang5@huawei.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Nadav Amit <namit@vmware.com>
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pedro Demarchi Gomes <pedrodemargomes@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Bit 52 and bit 55 don't have to be zero: they only trigger a
translation-specifiation exception if the PTE is marked as valid, which is
not the case for swap ptes.
Document which bits are used for what, and which ones are unused.
Link: https://lkml.kernel.org/r/20220329164329.208407-6-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Don Dutile <ddutile@redhat.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jann Horn <jannh@google.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Liang Zhang <zhangliang5@huawei.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Nadav Amit <namit@vmware.com>
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pedro Demarchi Gomes <pedrodemargomes@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
With z10 as minimum supported machine generation many ".insn" encodings
could be now converted to instruction names. There are couple of exceptions
- stfle is used from the als code built for z900 and cannot be converted
- few ".insn" directives encode unsupported instruction formats
The generated code is identical before/after this change.
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Convert pgtable code so pte_val()/pXd_val() aren't used as lvalue
anymore. This allows in later step to convert pte_val()/pXd_val() to
functions, which in turn makes it impossible to use these macros to
modify page table entries like they have been used before.
Therefore a construct like this:
pte_val(*pte) = __pa(addr) | prot;
which would directly write into a page table, isn't possible anymore
with the last step of this series.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Use the new set_pXd()/set_pte() helper functions at all places where
page table entries are modified.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Add set_pte_bit()/clear_pte_bit() and set_pXd_bit()/clear_pXd_bit
helper functions which are supposed to be used if bits within
ptes/pXds are set/cleared.
The only point of these helper functions is to get more readable
code. This is quite similar to what arm64 has.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Add set_pXd()/set_pte() helper functions which must be used to update
page table entries. The new helpers use WRITE_ONCE() to make sure that
a page table entry is written to only once.
Without this the compiler could otherwise generate code which writes
several times to a page table entry when updating its contents from
invalid to valid, which could lead to surprising results especially
for multithreaded processes...
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Pull s390 updates from Vasily Gorbik:
- Add support for ftrace with direct call and ftrace direct call
samples.
- Add support for kernel command lines longer than current 896 bytes
and make its length configurable.
- Add support for BEAR enhancement facility to improve last breaking
event instruction tracking.
- Add kprobes sanity checks and testcases to prevent kprobe in the mid
of an instruction.
- Allow concurrent access to /dev/hwc for the CPUMF users.
- Various ftrace / jump label improvements.
- Convert unwinder tests to KUnit.
- Add s390_iommu_aperture kernel parameter to tweak the limits on
concurrently usable DMA mappings.
- Add ap.useirq AP module option which can be used to disable interrupt
use.
- Add add_disk() error handling support to block device drivers.
- Drop arch specific and use generic implementation of strlcpy and
strrchr.
- Several __pa/__va usages fixes.
- Various cio, crypto, pci, kernel doc and other small fixes and
improvements all over the code.
[ Merge fixup as per https://lore.kernel.org/all/YXAqZ%2FEszRisunQw@osiris/ ]
* tag 's390-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (63 commits)
s390: make command line configurable
s390: support command lines longer than 896 bytes
s390/kexec_file: move kernel image size check
s390/pci: add s390_iommu_aperture kernel parameter
s390/spinlock: remove incorrect kernel doc indicator
s390/string: use generic strlcpy
s390/string: use generic strrchr
s390/ap: function rework based on compiler warning
s390/cio: make ccw_device_dma_* more robust
s390/vfio-ap: s390/crypto: fix all kernel-doc warnings
s390/hmcdrv: fix kernel doc comments
s390/ap: new module option ap.useirq
s390/cpumf: Allow multiple processes to access /dev/hwc
s390/bitops: return true/false (not 1/0) from bool functions
s390: add support for BEAR enhancement facility
s390: introduce nospec_uses_trampoline()
s390: rename last_break to pgm_last_break
s390/ptrace: add last_break member to pt_regs
s390/sclp: sort out physical vs virtual pointers usage
s390/setup: convert start and end initrd pointers to virtual
...
|
|
Introduce variants of the convert and destroy page functions that also
clear the PG_arch_1 bit used to mark them as secure pages.
The PG_arch_1 flag is always allowed to overindicate; using the new
functions introduced here allows to reduce the extent of overindication
and thus improve performance.
These new functions can only be called on pages for which a reference
is already being held.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Link: https://lore.kernel.org/r/20210920132502.36111-7-imbrenda@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Instructions IPTE, IDTE and CRDTE accept Page-Table Origin
as one of the arguments, but instead the pgtable virtual
address is passed. Fix that and also update the crdte()
prototype to conform to csp() and cspg() friends.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Print the real pte, pmd, etc. values instead of some hashed
value. Otherwise debugging would be even more difficult.
This also matches what most other architectures are doing.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use pr_err() to use a proper printk level.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Pull s390 updates from Vasily Gorbik:
- Rework inline asm to get rid of error prone "register asm"
constructs, which are problematic especially when code
instrumentation is enabled.
In particular introduce and use register pair union to allocate
even/odd register pairs. Unfortunately this breaks compatibility with
older clang compilers and minimum clang version for s390 has been
raised to 13.
https://lore.kernel.org/linux-next/CAK7LNARuSmPCEy-ak0erPrPTgZdGVypBROFhtw+=3spoGoYsyw@mail.gmail.com/
- Fix gcc 11 warnings, which triggered various minor reworks all over
the code.
- Add zstd kernel image compression support.
- Rework boot CPU lowcore handling.
- De-duplicate and move kernel memory layout setup logic earlier.
- Few fixes in preparation for FORTIFY_SOURCE performing compile-time
and run-time field bounds checking for mem functions.
- Remove broken and unused power management support leftovers in s390
drivers.
- Disable stack-protector for decompressor and purgatory to fix
buildroot build.
- Fix vt220 sclp console name to match the char device name.
- Enable HAVE_IOREMAP_PROT and add zpci_set_irq()/zpci_clear_irq() in
zPCI code.
- Remove some implausible WARN_ON_ONCEs and remove arch specific
counter transaction call backs in favour of default transaction
handling in perf code.
- Extend/add new uevents for online/config/mode state changes of AP
card / queue device in zcrypt.
- Minor entry and ccwgroup code improvements.
- Other small various fixes and improvements all over the code.
* tag 's390-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (91 commits)
s390/dasd: use register pair instead of register asm
s390/qdio: get rid of register asm
s390/ioasm: use symbolic names for asm operands
s390/ioasm: get rid of register asm
s390/cmf: get rid of register asm
s390/lib,string: get rid of register asm
s390/lib,uaccess: get rid of register asm
s390/string: get rid of register asm
s390/cmpxchg: use register pair instead of register asm
s390/mm,pages-states: get rid of register asm
s390/lib,xor: get rid of register asm
s390/timex: get rid of register asm
s390/hypfs: use register pair instead of register asm
s390/zcrypt: Switch to flexible array member
s390/speculation: Use statically initialized const for instructions
virtio/s390: get rid of open-coded kvm hypercall
s390/pci: add zpci_set_irq()/zpci_clear_irq()
scripts/min-tool-version.sh: Raise minimum clang version to 13.0.0 for s390
s390/ipl: use register pair instead of register asm
s390/mem_detect: fix tprot() program check new psw handling
...
|
|
Currently most platforms define pmd_pgtable() as pmd_page() duplicating
the same code all over. Instead just define a default value i.e
pmd_page() for pmd_pgtable() and let platforms override when required via
<asm/pgtable.h>. All the existing platform that override pmd_pgtable()
have been moved into their respective <asm/pgtable.h> header in order to
precede before the new generic definition. This makes it much cleaner
with reduced code.
Link: https://lkml.kernel.org/r/1623646133-20306-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Guo Ren <guoren@kernel.org>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently most platforms define FIRST_USER_ADDRESS as 0UL duplication the
same code all over. Instead just define a generic default value (i.e 0UL)
for FIRST_USER_ADDRESS and let the platforms override when required. This
makes it much cleaner with reduced code.
The default FIRST_USER_ADDRESS here would be skipped in <linux/pgtable.h>
when the given platform overrides its value via <asm/pgtable.h>.
Link: https://lkml.kernel.org/r/1620615725-24623-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Guo Ren <guoren@kernel.org> [csky]
Acked-by: Stafford Horne <shorne@gmail.com> [openrisc]
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com> [RISC-V]
Cc: Richard Henderson <rth@twiddle.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Guo Ren <guoren@kernel.org>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit c65e774fb3f6 ("x86/mm: Make PGDIR_SHIFT and PTRS_PER_P4D variable")
made PTRS_PER_P4D variable on x86 and introduced MAX_PTRS_PER_P4D as a
constant for cases which need a compile-time constant (e.g. fixed-size
arrays).
powerpc likewise has boot-time selectable MMU features which can cause
other mm "constants" to vary. For KASAN, we have some static
PTE/PMD/PUD/P4D arrays so we need compile-time maximums for all these
constants. Extend the MAX_PTRS_PER_ idiom, and place default definitions
in include/pgtable.h. These define MAX_PTRS_PER_x to be PTRS_PER_x unless
an architecture has defined MAX_PTRS_PER_x in its arch headers.
Clean up pgtable-nop4d.h and s390's MAX_PTRS_PER_P4D definitions while
we're at it: both can just pick up the default now.
Link: https://lkml.kernel.org/r/20210624034050.511391-4-dja@axtens.net
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Currently there are two separate places where kernel memory layout has
to be known and adjusted:
1. early kasan setup.
2. paging setup later.
Those 2 places had to be kept in sync and adjusted to reflect peculiar
technical details of one another. With additional factors which influence
kernel memory layout like ultravisor secure storage limit, complexity
of keeping two things in sync grew up even more.
Besides that if we look forward towards creating identity mapping and
enabling DAT before jumping into uncompressed kernel - that would also
require full knowledge of and control over kernel memory layout.
So, de-duplicate and move kernel memory layout setup logic into
the decompressor.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
In commit b02002cc4c0f ("s390/pci: Implement ioremap_wc/prot() with
MIO") we implemented both ioremap_wc() and ioremap_prot() however until
now we had not set HAVE_IOREMAP_PROT in Kconfig, do so now.
This also requires implementing pte_pgprot() as this is used in the
generic_access_phys() code enabled by CONFIG_HAVE_IOREMAP_PROT. As with
ioremap_wc() we need to take the MMIO Write Back bit index into account.
Moreover since the pgprot value returned from pte_pgprot() is to be used
for mappings into kernel address space we must make sure that it uses
appropriate kernel page table protection bits. In particular a pgprot
value originally coming from userspace could have the _PAGE_PROTECT
bit set to enable fault based dirty bit accounting which would then make
the mapping inaccessible when used in kernel address space.
Fixes: b02002cc4c0f ("s390/pci: Implement ioremap_wc/prot() with MIO")
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
There is little sense in applying __pa() to a physical
address, but that what pfn_pXd() macros do.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
This update fixes semantics of pXd_deref macros which
are expected to return a CPU-addressable pointer.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Create a region 3 page table which contains only invalid entries, and
use that via "s390_invalid_asce" instead of the kernel ASCE whenever
there is either
- no user address space available, e.g. during early startup
- as an intermediate ASCE when address spaces are switched
This makes sure that user space accesses in such situations are
guaranteed to fail.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
We've seen several occurences in the past where the default vmalloc
size of 128GB is not sufficient. Therefore extend the default size.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
pmd/pud_deref() assume that they will never operate on large pmd/pud
entries, and therefore only use the non-large _xxx_ENTRY_ORIGIN mask.
With commit 9ec8fa8dc331b ("s390/vmemmap: extend modify_pagetable()
to handle vmemmap"), that assumption is no longer true, at least for
pmd_deref().
In theory, we could end up with wrong addresses because some of the
non-address bits of a large entry would not be masked out.
In practice, this does not (yet) show any impact, because vmemmap_free()
is currently never used for s390.
Fix pmd/pud_deref() to check for the entry type and use the
_xxx_ENTRY_ORIGIN_LARGE mask for large entries.
While at it, also move pmd/pud_pfn() around, in order to avoid code
duplication, because they do the same thing.
Fixes: 9ec8fa8dc331b ("s390/vmemmap: extend modify_pagetable() to handle vmemmap")
Cc: <stable@vger.kernel.org> # 5.9
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Pull s390 updates from Vasily Gorbik:
- Remove address space overrides using set_fs()
- Convert to generic vDSO
- Convert to generic page table dumper
- Add ARCH_HAS_DEBUG_WX support
- Add leap seconds handling support
- Add NVMe firmware-assisted kernel dump support
- Extend NVMe boot support with memory clearing control and addition of
kernel parameters
- AP bus and zcrypt api code rework. Add adapter configure/deconfigure
interface. Extend debug features. Add failure injection support
- Add ECC secure private keys support
- Add KASan support for running protected virtualization host with
4-level paging
- Utilize destroy page ultravisor call to speed up secure guests
shutdown
- Implement ioremap_wc() and ioremap_prot() with MIO in PCI code
- Various checksum improvements
- Other small various fixes and improvements all over the code
* tag 's390-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (85 commits)
s390/uaccess: fix indentation
s390/uaccess: add default cases for __put_user_fn()/__get_user_fn()
s390/zcrypt: fix wrong format specifications
s390/kprobes: move insn_page to text segment
s390/sie: fix typo in SIGP code description
s390/lib: fix kernel doc for memcmp()
s390/zcrypt: Introduce Failure Injection feature
s390/zcrypt: move ap_msg param one level up the call chain
s390/ap/zcrypt: revisit ap and zcrypt error handling
s390/ap: Support AP card SCLP config and deconfig operations
s390/sclp: Add support for SCLP AP adapter config/deconfig
s390/ap: add card/queue deconfig state
s390/ap: add error response code field for ap queue devices
s390/ap: split ap queue state machine state from device state
s390/zcrypt: New config switch CONFIG_ZCRYPT_DEBUG
s390/zcrypt: introduce msg tracking in zcrypt functions
s390/startup: correct early pgm check info formatting
s390: remove orphaned extern variables declarations
s390/kasan: make sure int handler always run with DAT on
s390/ipl: add support to control memory clearing for nvme re-IPL
...
|
|
Currently to make sure that every page table entry is read just once
gup_fast walks perform READ_ONCE and pass pXd value down to the next
gup_pXd_range function by value e.g.:
static int gup_pud_range(p4d_t p4d, unsigned long addr, unsigned long end,
unsigned int flags, struct page **pages, int *nr)
...
pudp = pud_offset(&p4d, addr);
This function passes a reference on that local value copy to pXd_offset,
and might get the very same pointer in return. This happens when the
level is folded (on most arches), and that pointer should not be
iterated.
On s390 due to the fact that each task might have different 5,4 or
3-level address translation and hence different levels folded the logic
is more complex and non-iteratable pointer to a local copy leads to
severe problems.
Here is an example of what happens with gup_fast on s390, for a task
with 3-level paging, crossing a 2 GB pud boundary:
// addr = 0x1007ffff000, end = 0x10080001000
static int gup_pud_range(p4d_t p4d, unsigned long addr, unsigned long end,
unsigned int flags, struct page **pages, int *nr)
{
unsigned long next;
pud_t *pudp;
// pud_offset returns &p4d itself (a pointer to a value on stack)
pudp = pud_offset(&p4d, addr);
do {
// on second iteratation reading "random" stack value
pud_t pud = READ_ONCE(*pudp);
// next = 0x10080000000, due to PUD_SIZE/MASK != PGDIR_SIZE/MASK on s390
next = pud_addr_end(addr, end);
...
} while (pudp++, addr = next, addr != end); // pudp++ iterating over stack
return 1;
}
This happens since s390 moved to common gup code with commit
d1874a0c2805 ("s390/mm: make the pxd_offset functions more robust") and
commit 1a42010cdc26 ("s390/mm: convert to the generic
get_user_pages_fast code").
s390 tried to mimic static level folding by changing pXd_offset
primitives to always calculate top level page table offset in pgd_offset
and just return the value passed when pXd_offset has to act as folded.
What is crucial for gup_fast and what has been overlooked is that
PxD_SIZE/MASK and thus pXd_addr_end should also change correspondingly.
And the latter is not possible with dynamic folding.
To fix the issue in addition to pXd values pass original pXdp pointers
down to gup_pXd_range functions. And introduce pXd_offset_lockless
helpers, which take an additional pXd entry value parameter. This has
already been discussed in
https://lkml.kernel.org/r/20190418100218.0a4afd51@mschwideX1
Fixes: 1a42010cdc26 ("s390/mm: convert to the generic get_user_pages_fast code")
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: <stable@vger.kernel.org> [5.2+]
Link: https://lkml.kernel.org/r/patch.git-943f1e5dcff2.your-ad-here.call-01599856292-ext-8676@work.hours
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
[hca@linux.ibm.com: add more markers, rename some markers]
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
With our current support for the new MIO PCI instructions, write
combining/write back MMIO memory can be obtained via the pci_iomap_wc()
and pci_iomap_wc_range() functions.
This is achieved by using the write back address for a specific bar
as provided in clp_store_query_pci_fn()
These functions are however not widely used and instead drivers often
rely on ioremap_wc() and ioremap_prot(), which on other platforms enable
write combining using a PTE flag set through the pgrprot value.
While we do not have a write combining flag in the low order flag bits
of the PTE like x86_64 does, with MIO support, there is a write back bit
in the physical address (bit 1 on z15) and thus also the PTE.
Which bit is used to toggle write back and whether it is available at
all, is however not fixed in the architecture. Instead we get this
information from the CLP Store Logical Processor Characteristics for PCI
command. When the write back bit is not provided we fall back to the
existing behavior.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
I can't come up with a satisfying reason why we still need the memory
segment list. We used to represent in the list:
- boot memory
- standby memory added via add_memory()
- loaded dcss segments
When loading/unloading dcss segments, we already track them in a
separate list and check for overlaps
(arch/s390/mm/extmem.c:segment_overlaps_others()) when loading segments.
The overlap check was introduced for some segments in
commit b2300b9efe1b ("[S390] dcssblk: add >2G DCSSs support and stacked
contiguous DCSSs support.")
and was extended to cover all dcss segments in
commit ca57114609d1 ("s390/extmem: remove code for 31 bit addressing
mode").
Although I doubt that overlaps with boot memory and standby memory
are relevant, let's reshuffle the checks in load_segment() to request
the resource first. This will bail out in case we have overlaps with
other resources (esp. boot memory and standby memory). The order
is now different compared to segment_unload() and segment_unload(), but
that should not matter.
This smells like a leftover from ancient times, let's get rid of it. We
can now convert vmem_remove_mapping() into a void function - everybody
ignored the return value already.
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200625150029.45019-1-david@redhat.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Tested-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [DCSS]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
All architectures define pte_index() as
(address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1)
and all architectures define pte_offset_kernel() as an entry in the array
of PTEs indexed by the pte_index().
For the most architectures the pte_offset_kernel() implementation relies
on the availability of pmd_page_vaddr() that converts a PMD entry value to
the virtual address of the page containing PTEs array.
Let's move x86 definitions of the PTE accessors to the generic place in
<linux/pgtable.h> and then simply drop the respective definitions from the
other architectures.
The architectures that didn't provide pmd_page_vaddr() are updated to have
that defined.
The generic implementation of pte_offset_kernel() can be overridden by an
architecture and alpha makes use of this because it has special ordering
requirements for its version of pte_offset_kernel().
[rppt@linux.ibm.com: v2]
Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org
[rppt@linux.ibm.com: update]
Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org
[rppt@linux.ibm.com: update]
Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org
[akpm@linux-foundation.org: fix x86 warning]
[sfr@canb.auug.org.au: fix powerpc build]
Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We will use this in later patch to do tlb flush when clearing pmd entries.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200505071729.54912-22-aneesh.kumar@linux.ibm.com
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- GICv4.1 support
- 32bit host removal
PPC:
- secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
- allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
- New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require
bulk modification of the page tables.
- Initial work on making nested SVM event injection more similar to
VMX, and less buggy.
- Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in
function names which occasionally means eptp, KVM too has
standardized on "pgd".
- A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
- Some removal of pointer chasing from kvm_x86_ops, which will also
be switched to static calls as soon as they are available.
- New Tigerlake CPUID features.
- More bugfixes, optimizations and cleanups.
Generic:
- selftests: cleanups, new MMU notifier stress test, steal-time test
- CSV output for kvm_stat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (277 commits)
x86/kvm: fix a missing-prototypes "vmread_error"
KVM: x86: Fix BUILD_BUG() in __cpuid_entry_get_reg() w/ CONFIG_UBSAN=y
KVM: VMX: Add a trampoline to fix VMREAD error handling
KVM: SVM: Annotate svm_x86_ops as __initdata
KVM: VMX: Annotate vmx_x86_ops as __initdata
KVM: x86: Drop __exit from kvm_x86_ops' hardware_unsetup()
KVM: x86: Copy kvm_x86_ops by value to eliminate layer of indirection
KVM: x86: Set kvm_x86_ops only after ->hardware_setup() completes
KVM: VMX: Configure runtime hooks using vmx_x86_ops
KVM: VMX: Move hardware_setup() definition below vmx_x86_ops
KVM: x86: Move init-only kvm_x86_ops to separate struct
KVM: Pass kvm_init()'s opaque param to additional arch funcs
s390/gmap: return proper error code on ksm unsharing
KVM: selftests: Fix cosmetic copy-paste error in vm_mem_region_move()
KVM: Fix out of range accesses to memslots
KVM: X86: Micro-optimize IPI fastpath delay
KVM: X86: Delay read msr data iff writes ICR MSR
KVM: PPC: Book3S HV: Add a capability for enabling secure guests
KVM: arm64: GICv4.1: Expose HW-based SGIs in debugfs
KVM: arm64: GICv4.1: Allow non-trapping WFI when using HW SGIs
...
|
|
On s390 there currently is no implementation of pud_write(). That was ok
as long as we had our own implementation of get_user_pages_fast() which
checked for pud protection by testing the bit directly w/o using
pud_write(). The other callers of pud_write() are not reachable on s390.
After commit 1a42010cdc26 ("s390/mm: convert to the generic
get_user_pages_fast code") we use the generic get_user_pages_fast(), which
does call pud_write() in pud_access_permitted() for FOLL_WRITE access on
a large pud. Without an s390 specific pud_write(), the generic version is
called, which contains a BUG() statement to remind us that we don't have a
proper implementation. This results in a kernel panic.
Fix this by providing an implementation of pud_write().
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: 1a42010cdc26 ("s390/mm: convert to the generic get_user_pages_fast code")
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
This provides the basic ultravisor calls and page table handling to cope
with secure guests:
- provide arch_make_page_accessible
- make pages accessible after unmapping of secure guests
- provide the ultravisor commands convert to/from secure
- provide the ultravisor commands pin/unpin shared
- provide callbacks to make pages secure (inacccessible)
- we check for the expected pin count to only make pages secure if the
host is not accessing them
- we fence hugetlbfs for secure pages
- add missing radix-tree include into gmap.h
The basic idea is that a page can have 3 states: secure, normal or
shared. The hypervisor can call into a firmware function called
ultravisor that allows to change the state of a page: convert from/to
secure. The convert from secure will encrypt the page and make it
available to the host and host I/O. The convert to secure will remove
the host capability to access this page.
The design is that on convert to secure we will wait until writeback and
page refs are indicating no host usage. At the same time the convert
from secure (export to host) will be called in common code when the
refcount or the writeback bit is already set. This avoids races between
convert from and to secure.
Then there is also the concept of shared pages. Those are kind of secure
where the host can still access those pages. We need to be notified when
the guest "unshares" such a page, basically doing a convert to secure by
then. There is a call "pin shared page" that we use instead of convert
from secure when possible.
We do use PG_arch_1 as an optimization to minimize the convert from
secure/pin shared.
Several comments have been added in the code to explain the logic in
the relevant places.
Co-developed-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
walk_page_range() is going to be allowed to walk page tables other than
those of user space. For this it needs to know when it has reached a
'leaf' entry in the page tables. This information is provided by the
p?d_leaf() functions/macros.
For s390, pud_large() and pmd_large() are already implemented as static
inline functions. Add a macro to provide the p?d_leaf names for the
generic code to use.
Link: http://lkml.kernel.org/r/20191218162402.45610-9-steven.price@arm.com
Signed-off-by: Steven Price <steven.price@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: "Liang, Kan" <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On older HW or under a hypervisor, w/o the instruction-execution-
protection (IEP) facility, and also w/o EDAT-1, a translation-specification
exception may be recognized when bit 55 of a pte is one (_PAGE_NOEXEC).
The current code tries to prevent setting _PAGE_NOEXEC in such cases,
by removing it within set_pte_at(). However, ptep_set_access_flags()
will modify a pte directly, w/o using set_pte_at(). There is at least
one scenario where this can result in an active pte with _PAGE_NOEXEC
set, which would then lead to a panic due to a translation-specification
exception (write to swapped out page):
do_swap_page
pte = mk_pte (with _PAGE_NOEXEC bit)
set_pte_at (will remove _PAGE_NOEXEC bit in page table, but keep it
in local variable pte)
vmf->orig_pte = pte (pte still contains _PAGE_NOEXEC bit)
do_wp_page
wp_page_reuse
entry = vmf->orig_pte (still with _PAGE_NOEXEC bit)
ptep_set_access_flags (writes entry with _PAGE_NOEXEC bit)
Fix this by clearing _PAGE_NOEXEC already in mk_pte_phys(), where the
pgprot value is applied, so that no pte with _PAGE_NOEXEC will ever be
visible, if it is not supported. The check in set_pte_at() can then also
be removed.
Cc: <stable@vger.kernel.org> # 4.11+
Fixes: 57d7f939e7bd ("s390: add no-execute support")
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
For pmds and puds, there are a couple of page table helper functions that
only make sense for large entries, like pxd_(mk)dirty/young/write etc.
We currently explicitly check if the entries are large, but in practice
those functions must never be used for normal entries, which point to lower
level page tables, so the code can be simplified.
This also fixes a theoretical bug, where common code could use one of the
functions before actually marking a pmd large, like this:
pmd = pmd_mkhuge(pmd_mkdirty(pmd))
With the current implementation, the resulting large pmd would not be dirty
as requested. This could in theory result in the loss of dirty information,
e.g. after collapsing into a transparent hugepage. Common code currently
always marks an entry large before using one of the functions, but there is
no hard requirement for this. The only requirement would be that it never
uses the functions for normal entries pointing to lower level page tables,
but they might be called before marking an entry large during its creation.
In order to avoid issues with future common code, and to simplify the page
table helpers, remove the checks for large entries and rely on common code
never using them for normal entries.
This was found by testing a patch from from Anshuman Khandual, which is
currently discussed on LKML ("mm/debug: Add tests validating architecture
page table helpers").
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The semantics of pmd/pud_bad() expect that large entries are reported as
bad, but we also check large entries for sanity.
There is currently no issue with this wrong behaviour, but let's conform
to the semantics by reporting large pmd/pud entries as bad, in order to
prevent future issues.
This was found by testing a patch from from Anshuman Khandual, which is
currently discussed on LKML ("mm/debug: Add tests validating architecture
page table helpers").
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Always inline asm inlines with variable operands for "i" constraints,
since they won't compile if the compiler would decide to not inline
them.
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Convert two functions to static inline to get ride of W=1 GCC warnings
like,
mm/gup.c: In function 'gup_pte_range':
mm/gup.c:1816:16: warning: variable 'ptem' set but not used
[-Wunused-but-set-variable]
pte_t *ptep, *ptem;
^~~~
mm/mmap.c: In function 'acct_stack_growth':
mm/mmap.c:2322:16: warning: variable 'new_start' set but not used
[-Wunused-but-set-variable]
unsigned long new_start;
^~~~~~~~~
Signed-off-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/lkml/1570138596-11913-1-git-send-email-cai@lca.pw/
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Both pgtable_cache_init() and pgd_cache_init() are used to initialize kmem
cache for page table allocations on several architectures that do not use
PAGE_SIZE tables for one or more levels of the page table hierarchy.
Most architectures do not implement these functions and use __weak default
NOP implementation of pgd_cache_init(). Since there is no such default
for pgtable_cache_init(), its empty stub is duplicated among most
architectures.
Rename the definitions of pgd_cache_init() to pgtable_cache_init() and
drop empty stubs of pgtable_cache_init().
Link: http://lkml.kernel.org/r/1566457046-22637-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Will Deacon <will@kernel.org> [arm64]
Acked-by: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm: remove quicklist page table caches".
A while ago Nicholas proposed to remove quicklist page table caches [1].
I've rebased his patch on the curren upstream and switched ia64 and sh to
use generic versions of PTE allocation.
[1] https://lore.kernel.org/linux-mm/20190711030339.20892-1-npiggin@gmail.com
This patch (of 3):
Remove page table allocator "quicklists". These have been around for a
long time, but have not got much traction in the last decade and are only
used on ia64 and sh architectures.
The numbers in the initial commit look interesting but probably don't
apply anymore. If anybody wants to resurrect this it's in the git
history, but it's unhelpful to have this code and divergent allocator
behaviour for minor archs.
Also it might be better to instead make more general improvements to page
allocator if this is still so slow.
Link: http://lkml.kernel.org/r/1565250728-21721-2-git-send-email-rppt@linux.ibm.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Few other crucial memory setup options are already handled in
the startup code. Those values are needed by kaslr and kasan
implementations. "vmalloc" is the last piece required for future
improvements such as early decision on kernel page levels depth required
for actual memory setup, as well as vmalloc memory area access monitoring
in kasan.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
Alexander Gordeev
Linus Torvalds
Claudio Imbrenda
Anshuman Khandual
David Hildenbrand
Vasily Gorbik
Heiko Carstens
Daniel Axtens
Niklas Schnelle
Gerald Schaefer
Mike Rapoport
Aneesh Kumar K.V
Gerald Schaefer
Steven Price
Heiko Carstens
Qian Cai
Nicholas Piggin