| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit e39d5ef67804 ("powerpc/5xxx: extend mpc8xxx_gpio driver to support
mpc512x gpios") implemented support for IRQ_TYPE_LEVEL_LOW flow type in
mpc512x via falling edge type. Do same for mpc85xx which support was added
in commit 345e5c8a1cc3 ("powerpc: Add interrupt support to mpc8xxx_gpio").
Fixes probing of lm90 hwmon driver on mpc85xx based board which use level
interrupt. Without it kernel prints error and refuse lm90 to work:
[ 15.258370] genirq: Setting trigger mode 8 for irq 49 failed (mpc8xxx_irq_set_type+0x0/0xf8)
[ 15.267168] lm90 0-004c: cannot request IRQ 49
[ 15.272708] lm90: probe of 0-004c failed with error -22
Fixes: 345e5c8a1cc3 ("powerpc: Add interrupt support to mpc8xxx_gpio")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Based on the normalized pattern:
this file is licensed under the terms of the gnu general public
license version 2 this program is licensed as is without any warranty
of any kind whether express or implied
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The return from the call to platform_get_irq() is int, it can be
a negative error code, however this is being assigned to an unsigned
int variable 'irqn', so making 'irqn' an int.
Eliminate the following coccicheck warning:
./drivers/gpio/gpio-mpc8xxx.c:391:5-21: WARNING: Unsigned expression
compared with zero: mpc8xxx_gc -> irqn < 0
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 0b39536cc699 ("gpio: mpc8xxx: Fix IRQ check in mpc8xxx_probe")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: 76c47d1449fc ("gpio: mpc8xxx: Add ACPI support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Pull gpio updates from Bartosz Golaszewski:
"We mostly have various improvements and refactoring all over the place
but also some interesting new features - like the virtio GPIO driver
that allows guest VMs to use host's GPIOs. We also have a new/old GPIO
driver for rockchip - this one has been split out of the pinctrl
driver.
Summary:
- new driver: gpio-virtio allowing a guest VM running linux to access
GPIO lines provided by the host
- split the GPIO driver out of the rockchip pin control driver
- add support for a new model to gpio-aspeed-sgpio, refactor the
driver and use generic device property interfaces, improve property
sanitization
- add ACPI support to gpio-tegra186
- improve the code setting the line names to support multiple GPIO
banks per device
- constify a bunch of OF functions in the core GPIO code and make the
declaration for one of the core OF functions we use consistent
within its header
- use software nodes in intel_quark_i2c_gpio
- add support for the gpio-line-names property in gpio-mt7621
- use the standard GPIO function for setting the GPIO names in
gpio-brcmstb
- fix a bunch of leaks and other bugs in gpio-mpc8xxx
- use generic pm callbacks in gpio-ml-ioh
- improve resource management and PM handling in gpio-mlxbf2
- modernize and improve the gpio-dwapb driver
- coding style improvements in gpio-rcar
- documentation fixes and improvements
- update the MAINTAINERS entry for gpio-zynq
- minor tweaks in several drivers"
* tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (35 commits)
gpio: mpc8xxx: Use 'devm_gpiochip_add_data()' to simplify the code and avoid a leak
gpio: mpc8xxx: Fix a potential double iounmap call in 'mpc8xxx_probe()'
gpio: mpc8xxx: Fix a resources leak in the error handling path of 'mpc8xxx_probe()'
gpio: viperboard: remove platform_set_drvdata() call in probe
gpio: virtio: Add missing mailings lists in MAINTAINERS entry
gpio: virtio: Fix sparse warnings
gpio: remove the obsolete MX35 3DS BOARD MC9S08DZ60 GPIO functions
gpio: max730x: Use the right include
gpio: Add virtio-gpio driver
gpio: mlxbf2: Use DEFINE_RES_MEM_NAMED() helper macro
gpio: mlxbf2: Use devm_platform_ioremap_resource()
gpio: mlxbf2: Drop wrong use of ACPI_PTR()
gpio: mlxbf2: Convert to device PM ops
gpio: dwapb: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert GPIO to use software nodes
gpio: dwapb: Read GPIO base from gpio-base property
gpio: dwapb: Unify ACPI enumeration checks in get_irq() and configure_irqs()
gpiolib: Deduplicate forward declaration in the consumer.h header
MAINTAINERS: update gpio-zynq.yaml reference
gpio: tegra186: Add ACPI support
...
|
|
If an error occurs after a 'gpiochip_add_data()' call it must be undone by
a corresponding 'gpiochip_remove()' as already done in the remove function.
To simplify the code a fix a leak in the error handling path of the probe,
use the managed version instead (i.e. 'devm_gpiochip_add_data()')
Fixes: 698b8eeaed72 ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Commit 76c47d1449fc ("gpio: mpc8xxx: Add ACPI support") has switched to a
managed version when dealing with 'mpc8xxx_gc->regs'. So the corresponding
'iounmap()' call in the error handling path and in the remove should be
removed to avoid a double unmap.
This also allows some simplification in the probe. All the error handling
paths related to managed resources can be direct returns and a NULL check
in what remains in the error handling path can be removed.
Fixes: 76c47d1449fc ("gpio: mpc8xxx: Add ACPI support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Commit 698b8eeaed72 ("gpio/mpc8xxx: change irq handler from chained to normal")
has introduced a new 'goto err;' at the very end of the function, but has
not updated the error handling path accordingly.
Add the now missing 'irq_domain_remove()' call which balances a previous
'irq_domain_create_linear() call.
Fixes: 698b8eeaed72 ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Pull irqchip updates from Marc Zyngier:
- API updates:
- Treewide conversion to generic_handle_domain_irq() for anything
that looks like a chained interrupt controller
- Update the irqdomain documentation
- Use of bitmap_zalloc() throughout the tree
- New functionalities:
- Support for GICv3 EPPI partitions
- Fixes:
- Qualcomm PDC hierarchy fixes
- Yet another priority decoding fix for the GICv3 pseudo-NMIs
- Fix the apple-aic driver irq_eoi() callback to always unmask
the interrupt
- Properly handle edge interrupts on loongson-pch-pic
- Let the mtk-sysirq driver advertise IRQCHIP_SKIP_SET_WAKE
Link: https://lore.kernel.org/r/20210828121013.2647964-1-maz@kernel.org
|
|
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
This reverts commit 3d5bfbd9716318b1ca5c38488aa69f64d38a9aa5.
When booting with threadirqs, it causes a splat
WARNING: CPU: 0 PID: 29 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1ec/0x27c
irq 66 handler irq_default_primary_handler+0x0/0x1c enabled interrupts
That splat later went away with commit 81e2073c175b ("genirq: Disable
interrupts for force threaded handlers"), which got backported to
-stable. However, when running an -rt kernel, the splat still
exists. Moreover, quoting Thomas Gleixner [1]
But 3d5bfbd97163 ("gpio: mpc8xxx: change the gpio interrupt flags.")
has nothing to do with that:
"Delete the interrupt IRQF_NO_THREAD flags in order to gpio interrupts
can be threaded to allow high-priority processes to preempt."
This changelog is blatantly wrong. In mainline forced irq threads
have always been invoked with softirqs disabled, which obviously
makes them non-preemptible.
So the patch didn't even do what its commit log said.
[1] https://lore.kernel.org/lkml/871r8zey88.ffs@nanos.tec.linutronix.de/
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Current implementation only supports DT, now add ACPI support.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Some Layerscape/QoriQ SoCs have input buffers which needs to be enabled
first. This was done in two different ways in the driver. Unify it.
This was tested on a LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Delete the interrupt IRQF_NO_THREAD flags in order to gpio interrupts
can be threaded to allow high-priority processes to preempt.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Linux 5.5-rc6
|
|
On these boards, the irq_set_type must point one valid function pointer
that can correctly set both edge and falling edge.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20191122061839.24904-1-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Dear Linus Walleij,
In old kernels, some APIs still try to use parent->of_node from struct gpio_chip,
and it could be resulted in kernel panic because parent is NULL. Adding platform
device to gpiochip->parent can fix this problem.
Signed-off-by: Johnson Chen <johnsonch.chen@moxa.com>
Link: https://patchwork.kernel.org/patch/11234609
Link: https://lore.kernel.org/r/HK0PR01MB3521489269F76467DFD7843FFA450@HK0PR01MB3521.apcprd01.prod.exchangelabs.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Qoriq requires the IBE register to be set to enable GPIO inputs to be
read. Set it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iX3HC-00069N-0T@rmk-PC.armlinux.org.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The per-SoC devtype structures can contain their own callbacks that
overwrite mpc8xxx_gpio_devtype_default.
The clear intention is that mpc8xxx_irq_set_type is used in case the SoC
does not specify a more specific callback. But what happens is that if
the SoC doesn't specify one, its .irq_set_type is de-facto NULL, and
this overwrites mpc8xxx_irq_set_type to a no-op. This means that the
following SoCs are affected:
- fsl,mpc8572-gpio
- fsl,ls1028a-gpio
- fsl,ls1088a-gpio
On these boards, the irq_set_type does exactly nothing, and the GPIO
controller keeps its GPICR register in the hardware-default state. On
the LS1028A, that is ACTIVE_BOTH, which means 2 interrupts are raised
even if the IRQ client requests LEVEL_HIGH. Another implication is that
the IRQs are not checked (e.g. level-triggered interrupts are not
rejected, although they are not supported).
Fixes: 82e39b0d8566 ("gpio: mpc8xxx: handle differences between incarnations at a single place")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20191115125551.31061-1-olteanv@gmail.com
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
More than one gpio controllers can share one interrupt, change the
driver to request shared irq.
While this will work, it will mess up userspace accounting of the number
of interrupts per second in tools such as vmstat. The reason is that
for every GPIO interrupt, /proc/interrupts records the count against GIC
interrupt 68 or 69, as well as the GPIO itself. So, for every GPIO
interrupt, the total number of interrupts that the system has seen
increments by two.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20191011005643.41007-1-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ls1028a and ls1088a platform share common special function.
The gpio hardware what they use is the same version.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20190808101628.36782-3-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is a device specify register(named GPIO_IBE)
on ls1028a need to enable in initial stage.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20190718094902.15562-2-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The MPC8xxx driver is always instantiating its generic GPIO functions
with the flag BGPIOF_BIG_ENDIAN. This means "big-endian bit order"
and means the bits representing the GPIO lines in the registers are
reversed around 31 bits so line 0 is at bit 31 and so forth down to
line 31 in bit 0.
Instead of looping into the generic MMIO gpio to do the simple
calculation of a bitmask, through a vtable call with two parameters
likely using stack frames etc (unless the compiler optimize it)
and obscuring the view for the programmer, let's just open-code
what the call does. This likely executes faster, saves space and
makes the code easier to read.
Cc: Liu Gang <Gang.Liu@nxp.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tien Hock Loh <thloh@altera.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
From the beginning of the gpio-mpc8xxx.c, the "handle_level_irq"
has being used to handle GPIO interrupts in the PowerPC/Layerscape
platforms. But actually, almost all PowerPC/Layerscape platforms
assert an interrupt request upon either a high-to-low change or
any change on the state of the signal.
So the "handle_level_irq" is not reasonable for PowerPC/Layerscape
GPIO interrupt, it should be "handle_edge_irq". Otherwise the system
may lost some interrupts from the PIN's state changes.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Setting gc->direction_output to gc->direction_output looks strange.
I think this change makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
*read_reg and *write_reg can be removed because at all the places to call
them, we can just use gc->read_reg/gc->write_reg instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For devtype with specific gpio_dir_out implementation, current code is
wrong because below code sets both gc->direction_output and
mpc8xxx_gc->direction_output to the same function.
gc->direction_output = devtype->gpio_dir_out ?: gc->direction_output;
mpc8xxx_gc->direction_output = gc->direction_output;
Set mpc8xxx_gc->direction_output = gc->direction_output first to fix it.
This way mpc8xxx_gc->direction_output actually calls the standard
bgpio_dir_out() to update register.
Fixes: commit 42178e2a1e42 ("drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The new Layerscape platforms has the same ip block/controller
as GPIO on PowerPC platforms(MPC8XXX), but the GPIO registers
may be big or little endian. So the code needs to get the
endian property from DTB, then make additional functions to
fit all the PowerPC/Layerscape GPIO register read/write
operations.
gpio-generic.c provides an universal infrastructure for both
big and little endian register operations. So switch the
gpio-mpc8xxx to use gpio-generic can simplify the driver and
reduce a lot of code.
The IRQ and some workaround parts in gpio-mpc8xxx.c will be
updated with the new API interfaces but following the
original functionalities.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 709d71a17c33 ("gpio: mpc8xxx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.
Fixes: 709d71a17c33 ("gpio: mpc8xxx: use gpiochip data pointer")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
|
|
mpc8xxx_gpio_chip.lock needs to be a real spinlock in preempt-rt.
Especially the interrupt related functions can not be converted to a
sleeping lock.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio controller on MPC5125 is identical to the MPC5121 register
wise, the only difference is that the lines 0..3 are input only instead
of 28..31 on MPC5121.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio controllers that are handled by the mpc8xxx driver differ
slightly. Up to now some differences were handled by use of
of_device_is_compatible, others by use of struct of_device_id's data.
To make this consistent and easily extendable handle the differences at
a single place.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This variable is not modified in the driver and all functions it it
passed to don't change it either. So it can and should be marked const.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
|
|
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit 98686d9a52ee ("gpio: mpc8xxx: Convert to platform device
interface"), we get the following section mismatch warning. Remove the
__initdata annotation to fix it.
WARNING: vmlinux.o(.data+0xbc28): Section mismatch in reference from the variable mpc8xxx_plat_driver to the variable .init.data:mpc8xxx_gpio_ids
The variable mpc8xxx_plat_driver references
the variable __initdata mpc8xxx_gpio_ids
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since d621e8bae5ac9c67 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This way we do not need to transverse the device tree manually.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a set_multiple function to the MPC8xxx GPIO chip driver and thereby allow
for actual performance improvements when setting multiple outputs
simultaneously. In my case the time needed to configure an FPGA goes down from
48 s to 20 s.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - no change
v4: - change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
v3: - change commit message
v2: - add this patch (v1 included only changes to gpiolib)
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:
1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.
The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.
The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.
Cc: stable@vger.kernel.org
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
|
|
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
|
|
Exporting gpios over sysfs GPIO interface throws genirq
error messages, i.e. on an mpc5121 based board exporting
GPIO 5 triggers it:
# echo 229 > /sys/class/gpio/export
genirq: Setting trigger mode 0 for irq 44 failed
(mpc512x_irq_set_type+0x0/0x18c)
Similar error messages appear in the kernel boot log since the
board specifies GPIOs for matrix keypad and also SD Card write
protect and card detect GPIOs in its device tree. For all these
GPIOs there is an error message in the log.
The issue is triggered by setting the irq type to IRQ_TYPE_NONE
in the driver's irq_domain map function mpc8xxx_gpio_irq_map().
...
mpc8xxx_gpio_irq_map
irq_set_irq_type
__irq_set_trigger
__irq_set_trigger() calls irq_set_type() callback of the mpc8xxx gpio
irq chip with the IRQ_TYPE_NONE in its 'flags' argument. This callback
is either mpc8xxx_irq_set_type() or mpc512x_irq_set_type(). Both these
functions return -EINVAL in the case if IRQ_TYPE_NONE is passed in the
flow_type argument. This return value triggers the observed error
message in __irq_set_trigger(). Modifying these callbacks to not
return an error in IRQ_TYPE_NONE case doesn't make any sense to me.
The line setting IRQ_TYPE_NONE type has been originally added by
commit 345e5c8a "powerpc: Add interrupt support to mpc8xxx_gpio".
At this time set_irq_type() checked its type argument and returned 0
if the type argument didn't specify any meaningful type in its type
sense bits (and thus was equal to IRQ_TYPE_NONE). Effectively this
line was a nop and I wonder what was the point of adding it.
Remove IRQ_TYPE_NONE setting in the irq_domain mapping function.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/gpio/gpio-mpc8xxx.c: In function 'mpc8xxx_add_controller':
drivers/gpio/gpio-mpc8xxx.c:360:30: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
commit cfadd838(powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO
driver) added an unconditional call of chip->irq_eoi() to the demux
handler.
This leads to a NULL pointer derefernce on MPC512x platforms which use
this driver as well.
Make it conditional.
Reported-by: Thomas Wucher <thwucher@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Felix Radensky <felix@embedded-sol.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
Pali Rohár
Thomas Gleixner
Yang Li
Miaoqian Lin
Linus Torvalds
Christophe JAILLET
Marc Zyngier
Rasmus Villemoes
Ran Wang
Michael Walle
Song Hui
Linus Walleij
Johnson CH Chen (陳昭勳)
Russell King
Vladimir Oltean
Rob Herring
Liu Gang
Axel Lin
Guenter Roeck
Alexander Stein
Uwe Kleine-König
Krzysztof Kozlowski
Kevin Hao
Ricardo Ribalda Delgado
Rojhalat Ibrahim
Liu Gang
Rob Herring
Anatolij Gustschin