aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/mtd/nand/raw/marvell_nand.c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2022-10-18mtd: rawnand: marvell: Use correct logic for nand-keep-configTony O'Brien1-1/+1
Originally the absence of the marvell,nand-keep-config property caused the setup_data_interface function to be provided. However when setup_data_interface was moved into nand_controller_ops the logic was unintentionally inverted. Update the logic so that only if the marvell,nand-keep-config property is present the bootloader NAND config kept. Cc: stable@vger.kernel.org Fixes: 7a08dbaedd36 ("mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops") Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220927024728.28447-1-chris.packham@alliedtelesis.co.nz
2022-09-21mtd: rawnand: marvell: Fix error handle regarding dma_map_sgJack Wang1-1/+7
dma_map_sg return 0 on error, in case of error return -EIO, also add the dma_unmap_sg as rollback on the following error. Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Richard Weinberger <richard@nod.at> Cc: Vignesh Raghavendra <vigneshr@ti.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Christophe Kerello <christophe.kerello@foss.st.com> Cc: Cai Huoqing <cai.huoqing@linux.dev> Cc: linux-mtd@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220819060801.10443-6-jinpu.wang@ionos.com
2021-06-18mtd: rawnand: marvell: Minor documentation correctionSouptick Joarder1-1/+1
Kernel test robot throws below warning -> drivers/mtd/nand/raw/marvell_nand.c:454: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst Minor documentation correction. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210607193736.4654-1-jrdr.linux@gmail.com
2021-06-18mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()Yang Yingliang1-1/+3
Add clk_disable_unprepare() on error path in marvell_nfc_resume(). Fixes: bd9c3f9b3c00 ("mtd: rawnand: marvell: add suspend and resume hooks") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210601125814.3260364-1-yangyingliang@huawei.com
2021-02-01mtd: rawnand: marvell: convert comma to semicolonZheng Yongjun1-1/+1
Replace a comma between expression statements by a semicolon. Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210108092314.18972-1-zhengyongjun3@huawei.com
2020-12-10mtd: rawnand: marvell: Drop useless lineMiquel Raynal1-6/+0
The raw NAND core now declares the on host ECC engine being the default if none is provided in the DT. Drop this line doing exactly the same from the Marvell driver. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201113124114.449-1-miquel.raynal@bootlin.com
2020-09-30mtd: rawnand: marvell: Fix and update kerneldocKrzysztof Kozlowski1-7/+16
Fix kerneldoc comments and add missing documentation for members to fix W=1 compile warnings like: drivers/mtd/nand/raw/marvell_nand.c:251: warning: cannot understand function prototype: 'struct marvell_hw_ecc_layout ' drivers/mtd/nand/raw/marvell_nand.c:342: warning: Function parameter or member 'layout' not described in 'marvell_nand_chip' Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-5-krzk@kernel.org
2020-09-30mtd: rawnand: marvell: Simplify with dev_err_probe()Krzysztof Kozlowski1-4/+1
Common pattern of handling deferred probe can be simplified with dev_err_probe(). Less code and the error value gets printed. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-4-krzk@kernel.org
2020-09-30mtd: rawnand: marvell: Support panic_write for mtdoopsChris Packham1-5/+33
Under a panic context we can't get an interrupt. Actively poll for the RB status when performing a panic_write. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200828011237.22066-1-chris.packham@alliedtelesis.co.nz
2020-09-28mtd: rawnand: Use nanddev_get/set_ecc_requirements() when relevantMiquel Raynal1-3/+5
Instead of accessing ->strength/step_size directly. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-15-miquel.raynal@bootlin.com
2020-09-28mtd: rawnand: Use the new ECC engine type enumerationMiquel Raynal1-8/+9
Mechanical switch from the legacy "mode" enumeration to the new "engine type" enumeration in drivers and board files. The device tree parsing is also updated to return the new enumeration from the old strings. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-11-miquel.raynal@bootlin.com
2020-08-27mtd: rawnand: Rename the ECC algorithm enumeration itemsMiquel Raynal1-5/+5
NAND_ECC_ is not a meaningful prefix, use NAND_ECC_ALGO_ instead. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-3-miquel.raynal@bootlin.com
2020-06-26mtd: rawnand: s/data_interface/interface_config/Miquel Raynal1-5/+4
The name/suffix data_interface is a bit misleading in that the field or functions actually represent a configuration that can be applied by the controller/chip. Let's rename all fields/functions/hooks that are worth renaming. Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2020-06-26mtd: rawnand: Hide the chip->data_interface indirectionMiquel Raynal1-3/+6
As a preparation for allocating the data interface structure dynamically (and rename it), let's avoid accessing chip->data_interface directly. Instead, we introduce a helper, nand_get_interface_config(), and use it to retrieve the current data interface configuration out of a nand_chip object. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-19-miquel.raynal@bootlin.com
2020-05-31mtd: rawnand: marvell: Stop using nand_release()Miquel Raynal1-1/+6
This helper is not very useful and very often people get confused: they use nand_release() instead of nand_cleanup(). Let's stop using nand_release() by calling mtd_device_unregister() and nand_cleanup() directly. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-26-miquel.raynal@bootlin.com
2020-05-11mtd: rawnand: Give the possibility to verify a read operation is supportedMiquel Raynal1-2/+2
This can be used to discriminate between two path in the parameter page detection: use data_in cycles (like before) if supported, use the CHANGE READ COLUMN command otherwise. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-9-miquel.raynal@bootlin.com
2020-05-11mtd: rawnand: marvell: Rename the ->correct() functionMiquel Raynal1-10/+9
There is no correction involved at this point, it is just a matter of reading registers and checking whether bitflips have occurred or not. Rename the function to clarify it. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-7-miquel.raynal@bootlin.com
2020-05-11mtd: rawnand: marvell: Rename a function to clarifyMiquel Raynal1-3/+3
Cosmetic change to clarify the purpose of the function. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-6-miquel.raynal@bootlin.com
2020-05-11mtd: rawnand: marvell: Fix probe error pathMiquel Raynal1-9/+14
Ensure all chips are deregistered and cleaned in case of error during the probe. Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-5-miquel.raynal@bootlin.com
2020-05-11mtd: rawnand: marvell: Use nand_cleanup() when the device is not yet registeredMiquel Raynal1-1/+1
Do not call nand_release() while the MTD device has not been registered, use nand_cleanup() instead. Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-4-miquel.raynal@bootlin.com
2020-05-11mtd: rawnand: marvell: Use devm_platform_ioremap_res()Miquel Raynal1-3/+1
Switch from the old platform_get_resource()/devm_ioremap_resource() couple to the newer devm_platform_ioremap_resource() helper. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-3-miquel.raynal@bootlin.com
2020-05-11mtd: rawnand: marvell: Fix the condition on a return codeMiquel Raynal1-1/+1
In a previous fix, I changed the condition on which the timeout of an IRQ is reached from: if (!ret) into: if (ret && !pending) While having a non-zero return code is usual in the Linux kernel, here ret comes from a wait_for_completion_timeout() which returns 0 when the waiting period is too long. Hence, the revised condition should be: if (!ret && !pending) The faulty patch did not produce any error because of the !pending condition so this change is finally purely cosmetic and does not change the actual driver behavior. Fixes: cafb56dd741e ("mtd: rawnand: marvell: prevent timeouts on a loaded machine") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-2-miquel.raynal@bootlin.com
2020-05-10mtd: rawnand: Take check_only into accountBoris Brezillon1-1/+2
->exec_op() is passed a check_only argument that encodes when the controller should just check whether the operation is supported or not without executing it. Some controllers simply ignore this arguments, others don't but keep modifying some of the registers before returning. Let's fix all those drivers. Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200418194217.1016060-1-boris.brezillon@collabora.com
2020-03-11mtd: rawnand: marvell: Use dma_request_chan() instead dma_request_slave_channel()Peter Ujfalusi1-5/+8
dma_request_slave_channel() is a wrapper on top of dma_request_chan() eating up the error code. Use using dma_request_chan() directly to return the real error code. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-4-peter.ujfalusi@ti.com
2020-03-11mtd: rawnand: marvell: Release DMA channel on errorPeter Ujfalusi1-6/+19
Release the DMA channel on errors after the channel has been successfully requested. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-3-peter.ujfalusi@ti.com
2020-03-11mtd: rawnand: Replace zero-length array with flexible-array memberGustavo A. R. Silva1-1/+1
The current codebase makes use of the zero-length array language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as these ones is a flexible array member[1][2], introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertently introduced[3] to the codebase from now on. Also, notice that, dynamic memory allocations won't be affected by this change: "Flexible array members have incomplete type, and so the sizeof operator may not be applied. As a quirk of the original implementation of zero-length arrays, sizeof evaluates to zero."[1] This issue was found with the help of Coccinelle. [1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [2] https://github.com/KSPP/linux/issues/21 [3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200226222722.GA18020@embeddedor
2019-10-08mtd: Remove dev_err() usage after platform_get_irq()Stephen Boyd1-3/+1
We don't need dev_err() messages when platform_get_irq() fails now that platform_get_irq() prints an error message itself when something goes wrong. Let's remove these prints with a simple semantic patch. // <smpl> @@ expression ret; struct platform_device *E; @@ ret = ( platform_get_irq(E, ...) | platform_get_irq_byname(E, ...) ); if ( \( ret < 0 \| ret <= 0 \) ) { ( -if (ret != -EPROBE_DEFER) -{ ... -dev_err(...); -... } | ... -dev_err(...); ) ... } // </smpl> While we're here, remove braces on if statements that only have one statement (manually). Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Richard Weinberger <richard@nod.at> Cc: Vignesh Raghavendra <vigneshr@ti.com> Cc: linux-mtd@lists.infradead.org Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-05-12Merge tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linuxLinus Torvalds1-30/+21
Pull MTD updates from Richard Weinberger: "MTD core changes: - New AFS partition parser - Update MAINTAINERS entry - Use of fall-throughs markers NAND core changes: - Support having the bad block markers in either the first, second or last page of a block. The combination of all three location is now possible. - Constification of NAND_OP_PARSER(_PATTERN) elements. - Generic NAND DT bindings changed to yaml format (can be used to check the proposed bindings. First platform to be fully supported: sunxi. - Stopped using several legacy hooks. - Preparation to use the generic NAND layer with the addition of several helpers and the removal of the struct nand_chip from generic functions. - Kconfig cleanup to prepare the introduction of external ECC engines support. - Fallthrough comments. - Introduction of the SPI-mem dirmap API for SPI-NAND devices. Raw NAND controller drivers changes: - nandsim: - Switch to ->exec-op(). - meson: - Misc cleanups and fixes. - New OOB layout. - Sunxi: - A23/A33 NAND DMA support. - Ingenic: - Full reorganization and cleanup. - Clear separation between NAND controller and ECC engine. - Support JZ4740 an JZ4725B. - Denali: - Clear controller/chip separation. - ->exec_op() migration. - Various cleanups. - fsl_elbc: - Enable software ECC support. - Atmel: - Sam9x60 support. - GPMI: - Introduce the GPMI_IS_MXS() macro. - Various trivial/spelling/coding style fixes. SPI NOR core changes: - Print all JEDEC ID bytes on error - Fix comment of spi_nor_find_best_erase_type() - Add region locking flags for s25fl512s SPI NOR controller drivers changes: - intel-spi: - Avoid crossing 4K address boundary on read/write - Add support for Intel Comet Lake SPI serial flash" * tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits) mtd: part: fix incorrect format specifier for an unsigned long long mtd: lpddr_cmds: Mark expected switch fall-through mtd: phram: Mark expected switch fall-throughs mtd: cfi_cmdset_0002: Mark expected switch fall-throughs mtd: cfi_util: mark expected switch fall-throughs MAINTAINERS: MTD Git repository is hosted on kernel.org MAINTAINERS: Update jffs2 entry mtd: afs: add v2 partition parsing mtd: afs: factor the IIS read into partition parser mtd: afs: factor footer parsing into the v1 part parsing mtd: factor out v1 partition parsing mtd: afs: simplify partition detection mtd: afs: simplify partition parsing mtd: partitions: Add OF support to AFS partitions mtd: partitions: Add AFS partitions DT bindings mtd: afs: Move AFS partition parser to parsers subdir mtd: maps: Make uclinux_ram_map static mtd: maps: Allow MTD_PHYSMAP with MTD_RAM MAINTAINERS: Add myself as MTD maintainer MAINTAINERS: Remove my name from the MTD and NAND entries ...
2019-04-25mtd: rawnand: marvell: Clean the controller state before each operationMiquel Raynal1-6/+6
Since the migration of the driver to stop using the legacy ->select_chip() hook, there is nothing deselecting the target anymore, thus the selection is not forced at the next access. Ensure the ND_RUN bit and the interrupts are always in a clean state. Cc: Daniel Mack <daniel@zonque.org> Cc: stable@vger.kernel.org Fixes: b25251414f6e00 ("mtd: rawnand: marvell: Stop implementing ->select_chip()") Suggested-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Daniel Mack <daniel@zonque.org> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Richard Weinberger <richard@nod.at>
2019-04-18mtd: rawnand: marvell: Fix helper name in commentMiquel Raynal1-1/+1
Since the migration of the driver to stop using the legacy ->select_chip() hook, the marvell_nfc_select_chip() helper has been 'renamed' to marvell_nfc_select_target(). Update a left-over reference to this helper in a comment in the ->resume() path. Fixes: b25251414f6e00 ("mtd: rawnand: marvell: Stop implementing ->select_chip()") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
2019-04-08mtd: rawnand: Get rid of chip->ecc_{strength,step}_dsBoris Brezillon1-3/+3
nand_device embeds a nand_ecc_req object which contains the minimum strength and step-size required by the NAND device. Drop the chip->ecc_{strength,step}_ds fields and use chip->base.eccreq.{strength,step_size} instead. Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2019-04-08mtd: rawnand: Provide a helper to get chip->data_bufBoris Brezillon1-26/+17
We plan to move cache related fields to a pagecache struct in nand_chip but some drivers access ->pagebuf directly to invalidate the cache before they start using ->data_buf. Let's provide an helper that returns a pointer to ->data_buf after invalidating the cache. Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2019-02-05mtd: rawnand: marvell: use struct_size() in devm_kzalloc()Gustavo A. R. Silva1-3/+2
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct foo { int stuff; void *entry[]; }; instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL); Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL); This code was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-12-15mtd: rawnand: marvell: prevent timeouts on a loaded machineMiquel Raynal1-3/+14
marvell_nfc_wait_op() waits for completion during 'timeout_ms' milliseconds before throwing an error. While the logic is fine, the value of 'timeout_ms' is given by the core and actually correspond to the maximum time the NAND chip will take to complete the operation. Assuming there is no overhead in the propagation of the interrupt signal to the the NAND controller (through the Ready/Busy line), this delay does not take into account the latency of the operating system. For instance, for a page write, the delay given by the core is rounded up to 1ms. Hence, when the machine is over loaded, there is chances that this timeout will be reached. There are two ways to solve this issue that are not incompatible: 1/ Enlarge the timeout value (if so, how much?). 2/ Check after the waiting method if we did not miss any interrupt because of the OS latency (an interrupt is still pending). In this case, we assume the operation exited successfully. We choose the second approach that is a must in all cases, with the possibility to also modify the timeout value to be, e.g. at least 1 second in all cases. Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver") Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-12-07mtd: rawnand: marvell: fix spelling mistake in kernel docMiquel Raynal1-1/+1
Correct the spelling mistake 'Regiters' -> 'Registers'. Fixes: 961ba15c48dd ("mtd: rawnand: marvell: Fix clock resource by adding a register clock") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-12-07mtd: rawnand: Move ->setup_data_interface() to nand_controller_opsBoris Brezillon1-1/+2
->setup_data_interface() is a controller specific method and should thus be placed in nand_controller_ops. In order to make that work with controllers that support keeping pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to inform the core it should skip the timings selection step. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-12-07mtd: rawnand: Move the ->exec_op() method to nand_controller_opsBoris Brezillon1-1/+1
->exec_op() is a controller method and has nothing to do in the nand_chip struct. Let's move it to the nand_controller_ops struct and adjust the core and drivers accordingly. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-12-07mtd: rawnand: marvell: Stop implementing ->select_chip()Boris Brezillon1-9/+18
Now that the CS to be selected is kept in chip->cur_cs and passed in nand_operation->cs, we can get rid of the ->select_chip() implementation and replace it by an internal function which is called from the chip->exec_op() and chip->ecc.read/write_xxx() hooks. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-23Merge tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtdLinus Torvalds1-88/+187
Pull mtd updates from Boris Brezillon: "SPI NOR core changes: - Support non-uniform erase size - Support controllers with limited TX fifo size Driver changes: - m25p80: Re-issue a WREN command after each write access - cadence: Pass a proper dir value to dma_[un]map_single() - fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B addressing opcodes are properly handled - intel-spi: Add a new PCI entry for Ice Lake Raw NAND core changes: - Two batchs of cleanups of the NAND API, including: * Deprecating a lot of interfaces (now replaced by ->exec_op()). * Moving code in separate drivers (JEDEC, ONFI), in private files (internals), in platform drivers, etc. * Functions/structures reordering. * Exclusive use of the nand_chip structure instead of the MTD one all across the subsystem. - Addition of the nand_wait_readrdy/rdy_op() helpers. Raw NAND controllers drivers changes: - Various coccinelle patches. - Marvell: * Use regmap_update_bits() for syscon access. * More documentation. * BCH failure path rework. * More layouts to be supported. * IRQ handler complete() condition fixed. - Fsl_ifc: * SRAM initialization fixed for newer controller versions. - Denali: * Fix licenses mismatch and use a SPDX tag. * Set SPARE_AREA_SKIP_BYTES register to 8 if unset. - Qualcomm: * Do not include dma-direct.h. - Docg4: * Removed. - Ams-delta: * Use of a GPIO lookup table * Internal machinery changes. Raw NAND chip drivers changes: - Toshiba: * Add support for Toshiba memory BENAND * Pass a single nand_chip object to the status helper. - ESMT: * New driver to retrieve the ECC requirements from the 5th ID byte. MTD changes: - physmap cleanups/fixe - gpio-addr-flash cleanups/fixes" * tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits) jffs2: free jffs2_sb_info through jffs2_kill_sb() mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash mtd: maps: gpio-addr-flash: Convert to gpiod mtd: maps: gpio-addr-flash: Replace array with an integer mtd: maps: gpio-addr-flash: Use order instead of size mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus mtd: devices: m25p80: Make sure WRITE_EN is issued before each write mtd: spi-nor: Support controllers with limited TX FIFO size mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single mtd: spi-nor: parse SFDP Sector Map Parameter Table mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories mtd: rawnand: marvell: fix the IRQ handler complete() condition mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered" mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper mtd: maps: gpio-addr-flash: Use devm_* functions mtd: maps: gpio-addr-flash: Fix ioremapped size mtd: maps: gpio-addr-flash: Replace custom printk mtd: physmap_of: Release resources on error ...
2018-10-08mtd: rawnand: marvell: fix the IRQ handler complete() conditionMiquel Raynal1-1/+1
With the current implementation, the complete() in the IRQ handler is supposed to be called only if the register status has one or the other RDY bit set. Other events might trigger an interrupt as well if enabled, but should not end-up with a complete() call. For this purpose, the code was checking if the other bits were set, in this case complete() was not called. This is wrong as two events might happen in a very tight time-frame and if the NDSR status read reports two bits set (eg. RDY(0) and RDDREQ) at the same time, complete() was not called. This logic would lead to timeouts in marvell_nfc_wait_op() and has been observed on PXA boards (NFCv1) in the Hamming write path. Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver") Cc: stable@vger.kernel.org Reported-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Daniel Mack <daniel@zonque.org>
2018-10-03mtd: rawnand: marvell: Add support for 8kiB pages NAND chips layoutKonstantin Porotchkin1-0/+2
Add support for two new layouts: 8kiB pages NAND chips, requesting either 4 or 8 bit of correctability per 512B step. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-03mtd: rawnand: marvell: support 8b/512B strength for 2kiB pages layoutMiquel Raynal1-3/+31
Add support for the layout used by 2kiB page NAND chips requesting at least 8-bit of correction per 512 bytes. This layout requires a bit of handling as: 1/ It can only fit if the NAND chip has at least 128 OOB bytes. 2/ The Bad Block Markers are located in the middle of the data bytes and shall not be used. 3/ It has been experimentally observed that, for certain layouts, the ECC engine tries to correct data while it should not because the errors are uncorrectable. While this is harmless for truly bad pages, it creates bitflips in empty pages. To avoid such scenario that augments artificially the number of bitflips we re-read in raw mode the entire page instead of just the ECC bytes. This is done only for this layout to avoid an unneeded penalty with other setups. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-03mtd: rawnand: marvell: rework BCH engine failure pathMiquel Raynal1-31/+42
We are about to support a new layout that triggers a faulty mechanism in BCH engine that creates bitflips in erased pages. Before adding the quirk that will workaround this issue, this patch just reworks a bit the section that handles ECC failures in BCH read path. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-03mtd: rawnand: Pass a nand_chip object to chip->setup_data_interface()Boris Brezillon1-2/+1
Let's make the raw NAND API consistent by patching all helpers and hooks to take a nand_chip object instead of an mtd_info one or remove the mtd_info object when both are passed. Let's tackle the chip->setup_data_interface() hook. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-03mtd: rawnand: Pass a nand_chip object to chip->select_chip()Boris Brezillon1-2/+1
Let's make the raw NAND API consistent by patching all helpers and hooks to take a nand_chip object instead of an mtd_info one or remove the mtd_info object when both are passed. Let's tackle the chip->select_chip() hook. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-03mtd: rawnand: Pass a nand_chip object to ecc->write_xxx() hooksBoris Brezillon1-16/+16
Let's make the raw NAND API consistent by patching all helpers and hooks to take a nand_chip object instead of an mtd_info one or remove the mtd_info object when both are passed. Let's tackle all ecc->write_xxx() hooks at once. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-03mtd: rawnand: Pass a nand_chip object to ecc->read_xxx() hooksBoris Brezillon1-18/+12
Let's make the raw NAND API consistent by patching all helpers and hooks to take a nand_chip object instead of an mtd_info one or remove the mtd_info object when both are passed. Let's tackle all ecc->read_xxx() hooks at once. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-03mtd: rawnand: Pass a nand_chip object to nand_release()Boris Brezillon1-2/+2
Let's make the raw NAND API consistent by patching all helpers to take a nand_chip object instead of an mtd_info one. Now is nand_release()'s turn. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-03mtd: rawnand: Pass a nand_chip object to nand_scan()Boris Brezillon1-1/+1
Let's make the raw NAND API consistent by patching all helpers to take a nand_chip object instead of an mtd_info one. We start with nand_scan(). Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-10mtd: rawnand: marvell: prevent harmless warningsMiquel Raynal1-1/+3
Since the addition of WARN_ON() in nand_subop_get_data/addr_len() helpers, this driver will produce harmless warnings (mostly at probe) just because it always calls the nand_subop_get_data_len() helper in the parsing function (even on non-data instructions, where this value is meaningless and unneeded). Fix these warnings by deriving the length only when it is relevant. Fixes: 760c435e0f85 ("mtd: rawnand: make subop helpers return unsigned values") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.