aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath/ath9k/mac.c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2018-01-16ath9k: add MSI supportRussell Hu1-0/+47
On new Intel platforms like ApolloLake, legacy interrupt mechanism (INTx) is not supported, so WLAN modules are not working because interrupts are missing, therefore this patch is to add MSI support to ath9k. With module paremeter "use_msi=1", ath9k driver would try to use MSI instead of INTx. Signed-off-by: Russell Hu <rhu@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-05-08mac80211: properly remove RX_ENC_FLAG_40MHZJohannes Berg1-2/+2
Somehow I missed this in my RX rate cleanup series, causing some drivers to not report correct bandwidth since this flag isn't used by mac80211 anymore. Fix this, and make hwsim also report higher bandwidths appropriately. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: separate encoding/bandwidth from flagsJohannes Berg1-0/+1
We currently use a lot of flags that are mutually incompatible, separate this out into actual encoding and bandwidth enum values. Much of this again done with spatch, with manual post-editing, mostly to add the switch statements and get rid of the conversions. @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_80MHZ +status->bw = RATE_INFO_BW_80 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_40MHZ +status->bw = RATE_INFO_BW_40 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_20MHZ +status->bw = RATE_INFO_BW_20 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_160MHZ +status->bw = RATE_INFO_BW_160 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_5MHZ +status->bw = RATE_INFO_BW_5 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_10MHZ +status->bw = RATE_INFO_BW_10 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_VHT +status->encoding = RX_ENC_VHT @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_HT +status->encoding = RX_ENC_HT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_VHT +status.encoding = RX_ENC_VHT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_HT +status.encoding = RX_ENC_HT @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_HT) +(status->encoding == RX_ENC_HT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_VHT) +(status->encoding == RX_ENC_VHT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_5MHZ) +(status->bw == RATE_INFO_BW_5) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_10MHZ) +(status->bw == RATE_INFO_BW_10) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_40MHZ) +(status->bw == RATE_INFO_BW_40) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_80MHZ) +(status->bw == RATE_INFO_BW_80) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_160MHZ) +(status->bw == RATE_INFO_BW_160) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: clean up rate encoding bits in RX statusJohannes Berg1-7/+7
In preparation for adding support for HE rates, clean up the driver report encoding for rate/bandwidth reporting on RX frames. Much of this patch was done with the following spatch: @@ expression status; @@ -status->flag & (RX_FLAG_HT | RX_FLAG_VHT) +status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT) @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORTPRE +status->enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status->flag & RX_FLAG_SHORTPRE +status->enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT +status->enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status->flag & RX_FLAG_HT +status->enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_40MHZ +status->enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status->flag & RX_FLAG_40MHZ +status->enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORT_GI +status->enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status->flag & RX_FLAG_SHORT_GI +status->enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT_GF +status->enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status->flag & RX_FLAG_HT_GF +status->enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_VHT +status->enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status->flag & RX_FLAG_VHT +status->enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_STBC_MASK +status->enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status->flag & RX_FLAG_STBC_MASK +status->enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_LDPC +status->enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status->flag & RX_FLAG_LDPC +status->enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_10MHZ +status->enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status->flag & RX_FLAG_10MHZ +status->enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_5MHZ +status->enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status->flag & RX_FLAG_5MHZ +status->enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_80MHZ +status->enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_80MHZ +status->enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_160MHZ +status->enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_160MHZ +status->enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_BF +status->enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_BF +status->enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status->flag op STBC << RX_FLAG_STBC_SHIFT +status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORTPRE +status.enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status.flag & RX_FLAG_SHORTPRE +status.enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT +status.enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status.flag & RX_FLAG_HT +status.enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_40MHZ +status.enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status.flag & RX_FLAG_40MHZ +status.enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORT_GI +status.enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status.flag & RX_FLAG_SHORT_GI +status.enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT_GF +status.enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status.flag & RX_FLAG_HT_GF +status.enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_VHT +status.enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status.flag & RX_FLAG_VHT +status.enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_STBC_MASK +status.enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status.flag & RX_FLAG_STBC_MASK +status.enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_LDPC +status.enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status.flag & RX_FLAG_LDPC +status.enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_10MHZ +status.enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status.flag & RX_FLAG_10MHZ +status.enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_5MHZ +status.enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status.flag & RX_FLAG_5MHZ +status.enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_80MHZ +status.enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_80MHZ +status.enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_160MHZ +status.enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_160MHZ +status.enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_BF +status.enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_BF +status.enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status.flag op STBC << RX_FLAG_STBC_SHIFT +status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ @@ -RX_FLAG_STBC_SHIFT +RX_ENC_FLAG_STBC_SHIFT Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-02-07ath9k: fix race condition in enabling/disabling IRQsFelix Fietkau1-10/+34
The code currently relies on refcounting to disable IRQs from within the IRQ handler and re-enabling them again after the tasklet has run. However, due to race conditions sometimes the IRQ handler might be called twice, or the tasklet may not run at all (if interrupted in the middle of a reset). This can cause nasty imbalances in the irq-disable refcount which will get the driver permanently stuck until the entire radio has been stopped and started again (ath_reset will not recover from this). Instead of using this fragile logic, change the code to ensure that running the irq handler during tasklet processing is safe, and leave the refcount untouched. Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-01-15ath9k: Add QCA956x HW supportMiaoqing Pan1-1/+2
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2014-12-01ath9k_hw: fix hardware queue allocationFelix Fietkau1-8/+1
The driver passes the desired hardware queue index for a WMM data queue in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which instead relied on the order in which the function is called. Cc: stable@vger.kernel.org Reported-by: Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-19ath9k_hw: Abort transmission for sleeping stationRajkumar Manoharan1-0/+22
The data transmission to the power save station should be aborted immediately, whenever the station informs sleep state. Right now the frames queued into into hardware are being transmitted until the hardware detects the power save station based excessive retries of the data frames due to unacknowlegdement. Then remaining frames are returned with filetered status and might be retried later by driver or mac80211. Per WFA certification testing, AP should not send out more than two frames after processing nullfunc with PM bit set from associated station. To speed up tx filtering, the pending frames in hardware queues for given station will be aborted immediately via tx filter registers. This transmit filters can be ignored if the descriptor is having invalid destination index or clear destination mask set. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: Disable AR_INTR_SYNC_HOST1_FATAL for QCA953xSujith Manoharan1-1/+1
Along with AR9340 and AR955x, this is also needed for the QCA953x SoC. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-03ath9k: Fix baseband watchdog interruptsSujith Manoharan1-3/+21
Program the required baseband watchdog interrupt mask to ensure that the correct watchdog interrupts are raised when the BB is hung for some reason. Also, use the capability HW_BB_WATCHDOG instead of relying on other flags. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k_hw: remove additional_swba_backoffFelix Fietkau1-2/+1
It is unused Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k: add support for reporting per-chain signal strengthFelix Fietkau1-12/+12
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14ath9k_hw: remove IS_CHAN_B()Felix Fietkau1-5/+1
Hardware 802.11b-only mode isn't supported by the driver (the device is configured for 802.11n/g instead). Simplify the code by removing checks for it. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-15ath9k: Identify first subframe in an A-MPDUSujith Manoharan1-2/+2
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-11Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davemJohn W. Linville1-4/+12
Conflicts: drivers/net/wireless/ath/ath9k/debug.c net/mac80211/iface.c
2013-05-30ath9k: check for Rx-STBC flag and pass it to ieee80211Oleksij Rempel1-0/+5
This patch make use of STBC flag in DMA RX descriptor. Only devices after ar9280 can provide this information. If card support it we will set HAVE_STBC flag, to show clint programm thet STBC is supported but not received. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-30ath9k: remove useless flag conversation.Oleksij Rempel1-4/+7
some flags used only outside of ath9k - In this case we can use "enum mac80211_rx_flags" and pass it upstream without extra conversation. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-24ath9k_hw: improve performance for AR934x v1.3+Felix Fietkau1-1/+1
AR934x v1.3 no longer needs the DCU backoff reduction workaround for preventing rx overruns, but in turn needs the number of usable Tx buffers to be reduced slightly. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-04-10ath9k: detect more kinds of invalid descriptorsFelix Fietkau1-0/+8
If AR_CRCErr, AR_PHYErr, AR_DecryptCRCErr or AR_MichaelErr is indicated in the rx status word, but AR_RxFrameOK is also set, the descriptor contents are typically invalid. This can show up as a warning about invalid MCS rates in a frame. Even with those checks in place, a descriptor with invalid MCS rates can still sometimes make it through to the driver (mostly on older hardware like AR91xx). Detect such errors in the last descriptor of a frame and discard the whole frame if present. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30ath9k: reorder error codes for spectralSimon Wunderlich1-4/+4
When using the spectral scan feature, frames with phy errors are returned for further processing to the driver. However, if the frames also have an invalid CRC (which seems to happen quite often), the frame is marked with bad CRC and not with the PHY error bit. The FFT processing function will thus miss the frames. Fix this by changing the precedence in error marking. Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-10ath9k: fix interrupt storms on queued hardware resetFelix Fietkau1-6/+12
commit b74713d04effbacd3d126ce94cec18742187b6ce "ath9k: Handle fatal interrupts properly" introduced a race condition, where IRQs are being left enabled, however the irq handler returns IRQ_HANDLED while the reset is still queued without addressing the IRQ cause. This leads to an IRQ storm that prevents the system from even getting to the reset code. Fix this by disabling IRQs in the handler without touching intr_ref_cnt. Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09ath9k: disable SYNC_HOST1_FATAL interrupts for AR9550Gabor Juhos1-1/+1
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23ath9k_hw: increase tx abort timeout for half/quarter channelsFelix Fietkau1-1/+9
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: remove ath9k_hw_gettxintrtxqsFelix Fietkau1-7/+0
The driver can just check the mask directly Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: clean up tx completion interrupt handlingFelix Fietkau1-4/+3
TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and used together, and they share the same bitmask in enum ath9k_tx_queue_flags. Simplify the code that tests for these flags. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: simplify tx queue interrupt mask handlingFelix Fietkau1-15/+11
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05ath9k_hw: enable interrupts for beacon tx completion eventsFelix Fietkau1-1/+5
Not doing so could cause the tx status queue to overflow during longer periods of time without non-beacon tx. These events are also required for proper drv_tx_last_beacon handling. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-16ath9k_hw: fix interpretation of the rx KeyMiss flagFelix Fietkau1-2/+3
Documentation states that the KeyMiss flag is only valid if RxFrameOK is unset, however empirical evidence has shown that this is false. When KeyMiss is set (and RxFrameOK is 1), the hardware passes a valid frame which has not been decrypted. The driver then falsely marks the frame as decrypted, and when using CCMP this corrupts the rx CCMP PN, leading to connection hangs. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-19ath: Convert ath_dbg(bar, ATH_DBG_<FOO>, to ath_dbg(bar, FOOJoe Perches1-20/+16
Add ATH_DBG_ to macros to shorten the uses and reduce the line count. Coalesce ath_dbg formats. Add missing spaces to coalesced formats. Add missing newline terminations to ath_dbg formats. Align ath_dbg arguments where appropriate. Standardize ath_dbg formats without periods. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: check for asynchronous MCI interrupt pendingMohammed Shafi Shajakhan1-1/+4
MCI interrupt is an asynchronous one, so take care of it by having a check in ath9k_hw_intrpend, which actually decides whether the interrupt is really for the driver from ath_isr Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: take care of enabling MCI interruptsMohammed Shafi Shajakhan1-4/+8
enable MCI interrupt when ath9k_hw_enable_interrupts is called, like during the completion of chip_reset before which the interrupts are disabled Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-31drivers/net: Add export.h to files using EXPORT_SYMBOL/THIS_MODULEPaul Gortmaker1-0/+1
These were getting the macros from an implicit module.h include via device.h, but we are planning to clean that up. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c This relatively recently added file uses EXPORT_SYMBOL and hence needs export.h included so that it is compatible with the module.h split up work. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-11ath9k_hw: fix a regression in key miss handlingFelix Fietkau1-2/+2
The commit "ath9k_hw: Fix incorrect key_miss handling" changed the code to only report key miss errors if a MIC error wasn't reported. When checking the flags in that order in the MAC code, it might miss some real events, because the value of the MIC error flag is undefined under some conditions. The primary issue addressed by the previous commit is making sure that MIC errors are properly reported on the STA side. This can be fixed in a better way by adding a separate rx status flag for key miss and ignoring it for multicast frames. This fix slightly improves stability in AP mode on some older hardware, like AR9132. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-11ath9k_hw: make ath9k_hw_set_interrupts use ah->imask by defaultFelix Fietkau1-3/+3
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-19ath9k_hw: clean up hardware revision checksFelix Fietkau1-1/+1
- AR_SREV_5416_20_OR_LATER is always true, remove it - AR_SREV_9280_20_OR_LATER is always true within eeprom_4k.c and eeprom_9287.c - (AR_SREV_9271 || AR_SREV_9285) is always true in eeprom_4k.c Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-16ath9k_hw: remove the old tx descriptor APIFelix Fietkau1-12/+0
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24ath9k: qinfo never be NULL in setuptxqueueRajkumar Manoharan1-15/+2
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24ath9k: Remove unused argument tsf from ath9k_hw_rxprocdescRajkumar Manoharan1-1/+1
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k: Use atomic reference count for interrupt opsRajkumar Manoharan1-1/+12
Let us enable/disable interrupts based on reference count. By doing this we can ensure that interrupts are never be enabled in the middle of tasklet processing. Instead of addressing corner cases like "ath9k: avoid enabling interrupts while processing rx", this approach handles it in generic manner. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k: do not enable interrupt on set interrupt maskRajkumar Manoharan1-3/+0
At preset set_interrupt also enables interrupt after changing mask. This is not necessary in all cases and also sometime it breaks the assumption that interrupt was disabled. So let us enable the interrupt explicity if it was disabled earlier. This could also avoid unnecessary register ops and also helps the follow up patch to have global ref count for interrupts ops. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-13ath9k_hw: Fix incorrect key_miss handlingSenthil Balasubramanian1-2/+1
Decryping frames on key_miss handling shouldn't be done for Michael MIC failed frames as h/w would have already decrypted such frames successfully anyway. Also leaving CRC and PHY error(where the frame is going to be dropped anyway), we are left to prcoess Decrypt error for which s/w decrypt is selected anway and so having key_miss as a separate check doesn't serve anything. So making key_miss handling mutually exlusive with other RX status handling makes much more sense. This patch addresses an issue with STA not reporting MIC failure events resulting in STA being disconnected immediately. Cc: stable@kernel.org Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19ath9k: Drag the driver to the year 2011Sujith Manoharan1-1/+1
The Times They Are a-Changin'. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-10ath9k_hw: Change DCU backoff thresh for AR9340Rajkumar Manoharan1-2/+7
By changing DCU backoff threshold for AR9340 to 1, helps to reduce rx overrurns seen while running bidirectional traffic. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-28ath9k_hw: Enable generic timer interrupt.Vivek Natarajan1-0/+3
Generic timer interrupt was not triggered unless autosleep was disabled. Since autosleep is enabled in the newer chipsets, enable generic timer for using with bt coex logic. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6John W. Linville1-3/+22
2011-04-25ath9k_hw: Disable INTR_HOST1_FATAL to avoid interrupt strom with ar9430Vasanthakumar Thiagarajan1-4/+6
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-12ath9k_hw: fix stopping rx DMA during resetsFelix Fietkau1-3/+22
During PHY errors, the MAC can sometimes fail to enter an idle state on older hardware (before AR9380) after an rx stop has been requested. This typically shows up in the kernel log with messages like these: ath: Could not stop RX, we could be confusing the DMA engine when we start RX up ------------[ cut here ]------------ WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]() Call Trace: [<8023f0e8>] dump_stack+0x8/0x34 [<80075050>] warn_slowpath_common+0x78/0xa4 [<80075094>] warn_slowpath_null+0x18/0x24 [<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k] [<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k] [<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k] When this happens, the state that the MAC enters is easy to identify and does not result in bogus DMA traffic, however to ensure a working state after a channel change, the hardware should still be reset. This patch adds detection for this specific MAC state, after which the above warnings completely disappear in my tests. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-04ath9k: cleanup few redundant macrosMohammed Shafi Shajakhan1-2/+0
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-30ath9k_hw: remove pCap->total_queuesFelix Fietkau1-33/+5
The EEPROM contains a field that can restrict the number of hardware queues, however this is not only useless (all the known chips contain the same number of hardware queues), but also potentially dangerous in case of a misprogrammed EEPROM (could trigger driver crashes), so let's just ignore it completely. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-30ath9k_hw: replace REG_READ+REG_WRITE with REG_RMWFelix Fietkau1-43/+30
It's easier to read and it slightly decreases code size Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.