Age | Commit message (Collapse) | Author | Files | Lines |
|
According to the Realtek propritary driver and the rtw88 driver, the
tx rates of the ack (includes block ack) are initialized with lower
tx rates (no HT rates) which is set by the RRSR register value. In
real cases, ack rate higher than current tx rate could lead to
difficulty for the receiving end to receive management/control frames.
The retransmission rate would be higher then expected when the driver
is acting as receiver and the RSSI is not good.
Cross out higer rates for ack packet before implementing dynamic rrsr
configuration like the commit 4830872685f8 ("rtw88: add dynamic rrsr
configuration").
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211001040044.1028708-1-chris.chiu@canonical.com
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 64 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.894819585@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update copyright year and email address.
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This powers down the 8192e correctly, or at least to the point where
the firmware will load again, when reloading the driver module.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These are primarily needed for SDIO/PCI parts, but the vendor driver
still sets them for some USB devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This adds TX antenna selection bit defines for OFDM mode.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This also renames REG_USB_AGG_{TO,TH} to REG_USB_AGG_{TIMEOUT,THRESH}
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Documentation for enabling USB aggregation and whether to select
interrupt or bulk delivery of interrupt events.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This reduce the use of magic values a little.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Longer term we should switch all the chips over to use this function
instead of the random chip specific ifdef hacks.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Adjust AFE before enabling PLL on 8192eu, probably also needed for
8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
8192eu has it's own IQK calibration procedure, and notably uses
undocumented RF register 0x56 in the process.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Set REG_QUEUE_CTRL and REG_ACLK_MON for 8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The vendor driver set register 0xfe58 REG_USB_HWPWM in it's init
sequence for 8192eu. Do the same here.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Improve descriptive names of some registers and add some additional
registers only found on nextgen chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This should help when reloading the driver for 8723bu devices
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implment 8723bu specific device power down, and make power_off() a
fileops function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use the bit define rather than hard code the value for REG_PWR_DATA bits.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Provide RF_T_METER register location for nextgen chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Vendor driver implements this for 8723b and 8821 series
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This initializes RX DMA aggregation on 8723bu. We should do this for
all parts eventually, and also init TX aggregation.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
List yet another new register found on the 8723b.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implement burst parameter sequence for 8723bu parts. Eventually this
should be moved into device specific sections.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This implements the 8723bu specific power on sequence as it is
different from that of the 8723au chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implement additional init sequence code for the 8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This should initialize the antennas on the 8723bu, but so far I am
still not receiving anything :( More work is needed.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a first stab of implementing rtl8723bu_config_channel(). For
now this will only do 20MHz channels.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The 8723bu also has it's own IQK calibration process. This is similar
in flow, but still different enough to warrent it's own
implementation, at least for now.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This adds some additional register definitions for 8723bu, as well as
a bit define for USB RXDMA aggregation in REG_RXDMA_AGG_PG_TH.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This introduces additional register definitions for newer generation
chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The newer generation chips have different interrupt registers.
Initialize this correct registers on 8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The 8192eu (and some other parts) will report an incorrect USB OUT
EP. This tells the chip to drop it - as per the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Newer chips can auto load the LLT table, it is no longer necessary to
build it manually in the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This implements the rtl8192eu power on sequence, and splits it off
from the rtl8192cu/rtl8723au power on sequence.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This identifies the chip vendors correctly and also picks the correct
firmware for rtl8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add comments describing how REG_RXFLTMAP0, REG_RXFLTMAP1 and REG_RXFLTMAP2
work.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is needed for chips with IOL support.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is an alternate driver for a number of Realtek WiFi USB devices,
including RTL8723AU, RTL8188CU, RTL8188RU, RTL8191CU, and RTL8192CU.
It was written from scratch utilizing the Linux mac80211 stack.
After spending months cleaning up the vendor provided rtl8723au
driver, which comes with it's own 802.11 stack included, I decided to
rewrite this driver from the bottom up.
Many thanks to Johannes Berg for 802.11 insights and help and Larry
Finger for help with the vendor driver.
The full git log for the development of this driver can be found here:
git git://git.kernel.org/pub/scm/linux/kernel/git/jes/linux.git
branch rtl8723au-mac80211
This driver is still under development, but has proven to be very
stable for me. It currently supports station mode only. It has support
for OFDM and CCK rates. It does lack certain features found in the
staging driver, such as power management, AMPDU, and 40MHz channel
support. In addition it does not support AD-HOC, AP, and monitor mode
support at this point.
The driver is known to work with the following devices:
Lenovo Yoga (rtl8723au)
TP-Link TL-WN823N (rtl8192cu)
Etekcity 6R (rtl8188cu)
Daffodil LAN03 (rtl8188cu)
Alfa AWUS036NHR (rtl8188ru)
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|