| Age | Commit message (Collapse) | Author | Files | Lines | |
|---|---|---|---|---|---|
| 2019-12-18 | staging: wfx: fix case of lack of tx_retry_policies |   Jérôme Pouiller | 1 | -2/+5 | |
| In some rare cases, driver may not have any available tx_retry_policies. In this case, the driver asks to mac80211 to stop sending data. However, it seems that a race is possible and a few frames can be sent to the driver. In this case, driver can't wait for free tx_retry_policies since wfx_tx() must be atomic. So, this patch fix this case by sending these frames with the special policy number 15. The firmware normally use policy 15 to send internal frames (PS-poll, beacons, etc...). So, it is not a so bad fallback. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-3-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: fix wrong error message | Jérôme Pouiller | 1 | -1/+3 | |
| The driver checks that the number of retries made by the device is coherent with the rate policy. However, this check make sense only if the device has returned RETRY_EXCEEDED. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-11-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: fix hif_set_mfp() with big endian hosts | Jérôme Pouiller | 1 | -1/+0 | |
| struct hif_mib_protected_mgmt_policy is an array of u8. There is no reason to swap its bytes. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-10-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: detect race condition in WEP authentication | Jérôme Pouiller | 1 | -0/+1 | |
| Current code has a special case to handle association with WEP. Before to rework the tx data handling, let's try to detect any possible misuse of this code. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-9-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: ensure that retry policy always fallbacks to MCS0 / 1Mbps | Jérôme Pouiller | 1 | -0/+11 | |
| When not using HT mode, minstrel always includes 1Mbps as fallback rate. But, when using HT mode, this fallback is not included. Yet, it seems that it could save some frames. So, this patch add it unconditionally. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-8-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: fix rate control handling | Jérôme Pouiller | 1 | -3/+3 | |
| A tx_retry_policy (the equivalent of a list of ieee80211_tx_rate in hardware API) is not able to include a rate multiple time. So currently, the driver merges the identical rates from the policy provided by minstrel (and it try to do the best choice it can in the associated flags) before to sent it to firmware. Until now, when rates are merged, field "count" is set to max(count1, count2). But, it means that the sum of retries for all rates could be far less than initial number of retries. So, this patch changes the value of field "count" to count1 + count2. Thus, sum of all retries for all rates stay the same. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-7-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: firmware does not support more than 32 total retries | Jérôme Pouiller | 1 | -1/+1 | |
| The sum of all retries for a Tx frame cannot be superior to 32. There are 4 rates at most. So this patch limits number of retries per rate to 8. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-6-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: use boolean appropriately | Jérôme Pouiller | 2 | -3/+3 | |
| The field 'uploaded' is used as a boolean, so call it a boolean. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-5-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: fix counter overflow | Jérôme Pouiller | 1 | -1/+1 | |
| Some weird behaviors were observed when connection is really good and packets are small. It appears that sometime, number of packets in queues can exceed 255 and generate an overflow in field usage_count. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-4-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: fix case of lack of tx_retry_policies | Jérôme Pouiller | 1 | -2/+5 | |
| In some rare cases, driver may not have any available tx_retry_policies. In this case, the driver asks to mac80211 to stop sending data. However, it seems that a race is possible and a few frames can be sent to the driver. In this case, driver can't wait for free tx_retry_policies since wfx_tx() must be atomic. So, this patch fix this case by sending these frames with the special policy number 15. The firmware normally use policy 15 to send internal frames (PS-poll, beacons, etc...). So, it is not a so bad fallback. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-3-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: fix the cache of rate policies on interface reset | Jérôme Pouiller | 3 | -3/+7 | |
| Device and driver maintain a cache of rate policies (aka. tx_retry_policy in hardware API). When hif_reset() is sent to hardware, device resets its cache of rate policies. In order to keep driver in sync, it is necessary to do the same on driver. Note, when driver tries to use a rate policy that has not been defined on device, data is sent at 1Mbps. So, this patch should fix abnormal throughput observed sometime after a reset of the interface. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-2-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-18 | staging: wfx: fix the cache of rate policies on interface reset | Jérôme Pouiller | 3 | -3/+7 | |
| Device and driver maintain a cache of rate policies (aka. tx_retry_policy in hardware API). When hif_reset() is sent to hardware, device resets its cache of rate policies. In order to keep driver in sync, it is necessary to do the same on driver. Note, when driver tries to use a rate policy that has not been defined on device, data is sent at 1Mbps. So, this patch should fix abnormal throughput observed sometime after a reset of the interface. Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Link: https://lore.kernel.org/r/20191217161318.31402-2-Jerome.Pouiller@silabs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: rtl8188eu: add spaces around operators in rtw_mlme_ext.c |   Michael Straube | 1 | -56/+57 | |
| Add missing spaces around operators to improve readability and clear checkpatch issues. Signed-off-by: Michael Straube <straube.linux@gmail.com> Link: https://lore.kernel.org/r/20191214100955.16670-2-straube.linux@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: rtl8188eu: cleanup comparsions to NULL in rtw_mlme_ext.c | Michael Straube | 1 | -19/+19 | |
| Cleanup comparsions to NULL reported by checkpatch. if (x == NULL) -> if (!x) if (x != NULL) -> if (x) Signed-off-by: Michael Straube <straube.linux@gmail.com> Link: https://lore.kernel.org/r/20191214100955.16670-1-straube.linux@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: most: use angle brackets in include path |   Christian Gromm | 6 | -6/+6 | |
| This patch replaces the double quotes in all include paths with angle brackets. Signed-off-by: Christian Gromm <christian.gromm@microchip.com> Link: https://lore.kernel.org/r/1576238662-16512-7-git-send-email-christian.gromm@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next |   Daniel Vetter | 1 | -14/+0 | |
| drm-misc-next for v5.6: UAPI Changes: - Add support for DMA-BUF HEAPS. Cross-subsystem Changes: - mipi dsi definition updates, pulled into drm-intel as well. - Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim. - Remove support for dma-buf kmap/kunmap. - Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well. Core Changes: - Small cleanups to ttm. - Fix SCDC definition. - Assorted cleanups to core. - Add todo to remove load/unload hooks, and use generic fbdev emulation. - Assorted documentation updates. - Use blocking ww lock in ttm fault handler. - Remove drm_fb_helper_fbdev_setup/teardown. - Warning fixes with W=1 for atomic. - Use drm_debug_enabled() instead of drm_debug flag testing in various drivers. - Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted) - Various kconfig indentation fixes in core and drivers. - Fix freeing transactions in dp-mst correctly. - Sean Paul is steping down as core maintainer. :-( - Add lockdep annotations for atomic locks vs dma-resv. - Prevent use-after-free for a bad job in drm_scheduler. - Fill out all block sizes in the P01x and P210 definitions. - Avoid division by zero in drm/rect, and fix bounds. - Add drm/rect selftests. - Add aspect ratio and alternate clocks for HDMI 4k modes. - Add todo for drm_framebuffer_funcs and fb_create cleanup. - Drop DRM_AUTH for prime import/export ioctls. - Clear DP-MST payload id tables downstream when initializating. - Fix for DSC throughput definition. - Add extra FEC definitions. - Fix fake offset in drm_gem_object_funs.mmap. - Stop using encoder->bridge in core directly - Handle bridge chaining slightly better. - Add backlight support to drm/panel, and use it in many panel drivers. - Increase max number of y420 modes from 128 to 256, as preparation to add the new modes. Driver Changes: - Small fixes all over. - Fix documentation in vkms. - Fix mmap_sem vs dma_resv in nouveau. - Small cleanup in komeda. - Add page flip support in gma500 for psb/cdv. - Add ddc symlink in the connector sysfs directory for many drivers. - Add support for analogic an6345, and fix small bugs in it. - Add atomic modesetting support to ast. - Fix radeon fault handler VMA race. - Switch udl to use generic shmem helpers. - Unconditional vblank handling for mcde. - Miscellaneous fixes to mcde. - Tweak debug output from komeda using debugfs. - Add gamma and color transform support to komeda for DOU-IPS. - Add support for sony acx424AKP panel. - Various small cleanups to gma500. - Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation. - Add support for Logic PD Type 28 panel. - Use drm_panel_* wrapper functions in exynos/tegra/msm. - Add devicetree bindings for generic DSI panels. - Don't include drm_pci.h directly in many drivers. - Add support for begin/end_cpu_access in udmabuf. - Stop using drm_get_pci_dev in gma500 and mga200. - Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access. - Add devfreq thermal support to panfrost. - Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager. - meson: Add support for OSD1 plane AFBC commit. - Stop displaying garbage when toggling ast primary plane on/off. - More cleanups and fixes to UDL. - Add D32 suport to komeda. - Remove globle copy of drm_dev in gma500. - Add support for Boe Himax8279d MIPI-DSI LCD panel. - Add support for ingenic JZ4770 panel. - Small null pointer deference fix in ingenic. - Remove support for the special tfp420 driver, as there is a generic way to do it. Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com | |||||
| 2019-12-17 | staging: most: configfs: reduce array size | Christian Gromm | 1 | -7/+9 | |
| This patch reduces the size of the arrays inside the mdev_link struct to a reasonable value. Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Christian Gromm <christian.gromm@microchip.com> Link: https://lore.kernel.org/r/1576238662-16512-6-git-send-email-christian.gromm@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: most: configfs: use strlcpy | Christian Gromm | 1 | -4/+6 | |
| This patch uses strlcpy to copy data provided by userspace in order to not overflow the allocated space. Signed-off-by: Christian Gromm <christian.gromm@microchip.com> Link: https://lore.kernel.org/r/1576238662-16512-5-git-send-email-christian.gromm@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: most: rename enum mbo_status_flags | Christian Gromm | 1 | -2/+2 | |
| The data structures of the most.h header file will be exposed to the kernel once the file is moved out of the staging area. This is why the name is prefixed with the string 'most'. Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Christian Gromm <christian.gromm@microchip.com> Link: https://lore.kernel.org/r/1576238662-16512-4-git-send-email-christian.gromm@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: most: rename struct core_component | Christian Gromm | 7 | -36/+36 | |
| The stuctures defined in the most.h header file will be exposed to the kernel once the file is moved out of the staging area. That's why the name is changed into something more descriptive. Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Christian Gromm <christian.gromm@microchip.com> Link: https://lore.kernel.org/r/1576238662-16512-3-git-send-email-christian.gromm@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: most: rename core.h to most.h | Christian Gromm | 10 | -9/+9 | |
| This patch renames the core header file core.h to most.h. The intention behind this is to have a meaningful name once this file is moved to the /include/linux directory. Signed-off-by: Christian Gromm <christian.gromm@microchip.com> Link: https://lore.kernel.org/r/1576238662-16512-2-git-send-email-christian.gromm@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: qlge: Fix CHECK: Alignment should match open parenthesis |   Scott Schafer | 4 | -130/+117 | |
| Fix CHECK: Alignment should match open parenthesis in qlge_dbg.c, qlge_ethtool.c, qlge_main.c, and qlge_mpi.c. Also made changes to the following lines: WARNING: quoted string split across lines FILE: drivers/staging/qlge/qlge_main.c:81 WARNING: quoted string split across lines FILE: drivers/staging/qlge/qlge_main.c:87 WARNING: quoted string split across lines FILE: drivers/staging/qlge/qlge_main.c:3528 WARNING: quoted string split across lines FILE: drivers/staging/qlge/qlge_main.c:3536 CHECK: spaces preferred around that '*' (ctx:VxV) drivers/staging/qlge/qlge_main.c:4102 I made these changes due to touching these lines in the original fix Signed-off-by: Scott Schafer <schaferjscott@gmail.com> Link: https://lore.kernel.org/r/27ec7ee0a3ba8c1ad946077aacfcc6e40b98c106.1576086080.git.schaferjscott@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: qlge: Fix CHECK extra blank lines in many files | Scott Schafer | 5 | -13/+0 | |
| Fix CHECK: Please don't use multiple blank lines in qlge.h, qlge_dbg.c, qlge_ethtool.c, qlge_main.c, and qlge_mpi.c Signed-off-by: Scott Schafer <schaferjscott@gmail.com> Link: https://lore.kernel.org/r/9387760ae35bdeb606dc03ca9dd167f5214cd3a8.1576086080.git.schaferjscott@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: octeon-usb: delete the octeon usb host controller driver |   Greg Kroah-Hartman | 7 | -5608/+0 | |
| This driver was merged back in 2013 and shows no progress toward every being merged into the "correct" part of the kernel. The code doesn't even build for anyone unless you have the specific hardware platform selected, so odds are it doesn't even work anymore. Remove it for now and is someone comes along that has the hardware and is willing to fix it up, it can be reverted. Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: David Daney <ddaney.cavm@gmail.com> Cc: Nishka Dasgupta <nishkadg.linux@gmail.com> Cc: Himadri Pandya <himadri18.07@gmail.com> Cc: "Frank A. Cancio Bello" <frank@generalsoftwareinc.com> Cc: Sumit Pundir <pundirsumit11@gmail.com> Cc: Laura Lazzati <laura.lazzati.15@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20191210091509.3546251-2-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: octeon: delete driver | Greg Kroah-Hartman | 21 | -4749/+0 | |
| This driver has been in the tree since 2009 with no real movement to get it out. Now it is starting to cause build issues and other problems for people who want to fix coding style problems, but can not actually build it. As nothing is happening here, just delete the module entirely. Reported-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Guenter Roeck <linux@roeck-us.net> Cc: David Daney <ddaney@caviumnetworks.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: YueHaibing <yuehaibing@huawei.com> Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Wambui Karuga <wambui.karugax@gmail.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Cc: Florian Westphal <fw@strlen.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Branden Bonaby <brandonbonaby94@gmail.com> Cc: "Petr Štetiar" <ynezz@true.cz> Cc: Sandro Volery <sandro@volery.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Giovanni Gherdovich <bobdc9664@seznam.cz> Cc: Valery Ivanov <ivalery111@gmail.com> Link: https://lore.kernel.org/r/20191210091509.3546251-1-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: axis-fifo: add unspecified HAS_IOMEM dependency |   Brendan Higgins | 1 | -1/+1 | |
| Currently CONFIG_XIL_AXIS_FIFO=y implicitly depends on CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get the following build error: ld: drivers/staging/axis-fifo/axis-fifo.o: in function `axis_fifo_probe': drivers/staging/axis-fifo/axis-fifo.c:809: undefined reference to `devm_ioremap_resource' Fix the build error by adding the unspecified dependency. Reported-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Brendan Higgins <brendanhiggins@google.com> Link: https://lore.kernel.org/r/20191211192742.95699-7-brendanhiggins@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-17 | staging: comedi: gsc_hpdi: check dma_alloc_coherent() return value |   Ian Abbott | 1 | -0/+10 | |
| The "auto-attach" handler function `gsc_hpdi_auto_attach()` calls `dma_alloc_coherent()` in a loop to allocate some DMA data buffers, and also calls it to allocate a buffer for a DMA descriptor chain. However, it does not check the return value of any of these calls. Change `gsc_hpdi_auto_attach()` to return `-ENOMEM` if any of these `dma_alloc_coherent()` calls fail. This will result in the comedi core calling the "detach" handler `gsc_hpdi_detach()` as part of the clean-up, which will call `gsc_hpdi_free_dma()` to free any allocated DMA coherent memory buffers. Cc: <stable@vger.kernel.org> #4.6+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20191216110823.216237-1-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-16 | media: hantro: Support color conversion via post-processing |   Ezequiel Garcia | 11 | -11/+343 | |
| The Hantro G1 decoder is able to enable a post-processor on the decoding pipeline, which can be used to perform scaling and color conversion. The post-processor is integrated to the decoder, and it's possible to use it in a way that is completely transparent to the user. This commit enables color conversion via post-processing, which means the driver now exposes YUV packed, in addition to NV12. Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | |||||
| 2019-12-16 | media: hantro: Rename {prepare,finish}_run to {start,end}_prepare_run | Ezequiel Garcia | 10 | -18/+18 | |
| hantro_prepare_run() and hantro_finish_run() are slightly misleading, so let's rename it to something a bit more clear. Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | |||||
| 2019-12-16 | media: hantro: Cleanup format negotiation helpers | Ezequiel Garcia | 1 | -33/+20 | |
| Format negotiation helpers, hantro_find_format() and hantro_get_default_fmt() can be simplified, making the code a little bit clearer. More importantly, this change is preparation work for the post-processor usage. Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | |||||
| 2019-12-16 | media: imx7-mipi-csis: remove subdev_notifier |   Rui Miguel Silva | 1 | -3/+0 | |
| It was defined a notifier in the csi_state structure that is never allocated. And besides that it's unregister in the remove, even though it is a no-op, just remove both. Fixes: 7807063b862b ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7") Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | |||||
| 2019-12-16 | media: meson: vdec: add sm1 platform |   Neil Armstrong | 4 | -7/+59 | |
| Add support for the Amlogic SM1 platform for the current MPEG1 & MPEG2 support. The SM1 family, very close to the G12A SoCs, has a slighly different power management control, thus needing a separate compatible and family id. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | |||||
| 2019-12-16 | media: meson: vdec: add g12a platform |   Maxime Jourdan | 4 | -2/+44 | |
| Add support for the G12A platform by: - adding the G12A codec support, here MPEG1 & MPEG2 - getting the new hevcf clock for the upcoming HEVC/VP9 decoding support Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | |||||
| 2019-12-16 | Merge 5.5-rc2 into staging-next | Greg Kroah-Hartman | 13 | -22/+39 | |
| We want the staging driver fixes in here, and this resolves merge issues with the isdn code that was pointed out in linux-next Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-15 | staging: iio: accel: adis16240: enforce SPI mode on probe function |   Rodrigo Carvalho | 1 | -0/+7 | |
| According to the datasheet, this driver supports only SPI mode 3, so we should enforce it on probe function. Signed-off-by: Rodrigo Carvalho <rodrigorsdc@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> | |||||
| 2019-12-14 | Merge tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging |   Linus Torvalds | 13 | -25/+56 | |
| Pull staging/IIO fixes from Greg KH: "Here are a number of small staging and IIO driver fixes for reported issues for 5.5-rc2 Nothing major, a bunch of tiny IIO driver issues resolved, and some staging driver fixes for things that people ran into with 5.5-rc1. Full details are in the shortlog. All of these have been in linux-next with no reported issues" * tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits) fbtft: Fix the initialization from property algorithm staging: rtl8712: fix interface sanity check staging: rtl8188eu: fix interface sanity check staging: gigaset: add endpoint-type sanity check staging: gigaset: fix illegal free on probe errors staging: gigaset: fix general protection fault on probe staging: vchiq: call unregister_chrdev_region() when driver registration fails staging: exfat: fix multiple definition error of `rename_file' staging/wlan-ng: add CRC32 dependency in Kconfig staging: hp100: Fix build error without ETHERNET staging: fbtft: Do not hardcode SPI CS polarity inversion staging: exfat: properly support discard in clr_alloc_bitmap() staging/octeon: Mark Ethernet driver as BROKEN iio: adc: max9611: Fix too short conversion time delay iio: ad7949: fix channels mixups iio: imu: st_lsm6dsx: do not power-off accel if events are enabled iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask iio: imu: st_lsm6dsx: fix decimation factor estimation iio: imu: inv_mpu6050: fix temperature reporting using bad unit iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting ... | |||||
| 2019-12-13 | media: meson: add missing allocation failure check on new_buf |   Colin Ian King | 1 | -0/+2 | |
| Currently if the allocation of new_buf fails then a null pointer dereference occurs when assiging new_buf->vb. Avoid this by returning early on a memory allocation failure as there is not much more can be done at this point. Addresses-Coverity: ("Dereference null return") Fixes: 3e7f51bd9607 ("media: meson: add v4l2 m2m video decoder driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | |||||
| 2019-12-12 | netdev: pass the stuck queue to the timeout handler |   Michael S. Tsirkin | 6 | -8/+8 | |
| This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-11 | staging: remove isdn capi drivers |   Arnd Bergmann | 45 | -22757/+0 | |
| As described in drivers/staging/isdn/TODO, the drivers are all assumed to be unmaintained and unused now, with gigaset being the last one to stop being maintained after Paul Bolle lost access to an ISDN network. The CAPI subsystem remains for now, as it is still required by bluetooth/cmtp. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20191210210455.3475361-1-arnd@arndb.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: rtl8723bs: Fix line length |   Andreas Hellmich | 3 | -29/+37 | |
| Fix some line length errors. Co-developed-by: Annika Knepper <av91obul@stud.informatik.uni-erlangen.de> Signed-off-by: Annika Knepper <av91obul@stud.informatik.uni-erlangen.de> Signed-off-by: Andreas Hellmich <dy26hofu@stud.informatik.uni-erlangen.de> Link: https://lore.kernel.org/r/20191129093939.2782-2-dy26hofu@stud.informatik.uni-erlangen.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: rtl8723bs: Fix spelling errors | Andreas Hellmich | 3 | -28/+28 | |
| Fix spelling errors. Co-developed-by: Annika Knepper <av91obul@stud.informatik.uni-erlangen.de> Signed-off-by: Annika Knepper <av91obul@stud.informatik.uni-erlangen.de> Signed-off-by: Andreas Hellmich <dy26hofu@stud.informatik.uni-erlangen.de> Link: https://lore.kernel.org/r/20191129093939.2782-1-dy26hofu@stud.informatik.uni-erlangen.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | fbtft: Fix the initialization from property algorithm |   Andy Shevchenko | 1 | -3/+3 | |
| When converting to device property API the commit 8b2d3aeeb7ec ("fbtft: Make use of device property API") mistakenly placed the reading of the first value inside the loop, that jumps over value after initialization sequence or sleep commands. Move the above mentioned reading outside of the loop to restore correct behaviour. Besides that, we are using pre-increment operation which may lead to out of the boundary access at the end of sequence. Thus, allocate buffer with an additional element at the end to prevent out of the boundary access. Fixes: 8b2d3aeeb7ec ("fbtft: Make use of device property API") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20191121140207.65089-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: bcm2835-audio: Drop superfluous ioctl PCM ops |   Takashi Iwai | 1 | -2/+0 | |
| PCM core deals the empty ioctl field now as default. Let's kill the redundant lines. Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20191210141356.18074-5-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: most: Drop superfluous ioctl PCM ops | Takashi Iwai | 1 | -1/+0 | |
| PCM core deals the empty ioctl field now as default. Let's kill the redundant lines. Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20191210141356.18074-4-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: bcm2835-audio: Use managed buffer allocation | Takashi Iwai | 1 | -16/+1 | |
| Clean up the driver with the new managed buffer allocation API. The hw_params and hw_free callbacks became superfluous and dropped. Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20191210141356.18074-3-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: most: Use managed buffer allocation | Takashi Iwai | 1 | -43/+1 | |
| Clean up the driver with the new managed buffer allocation API. Also remove the unnecessary checks of channels in hw_params callback as this is guaranteed by the hw constraints in anyway. After these cleanups, the hw_params and hw_free callbacks became empty, hence dropped. Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20191210141356.18074-2-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: rtl8712: fix interface sanity check |   Johan Hovold | 1 | -1/+1 | |
| Make sure to use the current alternate setting when verifying the interface descriptors to avoid binding to an invalid interface. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel") Cc: stable <stable@vger.kernel.org> # 2.6.37 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191210114751.5119-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: rtl8188eu: fix interface sanity check | Johan Hovold | 1 | -1/+1 | |
| Make sure to use the current alternate setting when verifying the interface descriptors to avoid binding to an invalid interface. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: c2478d39076b ("staging: r8188eu: Add files for new driver - part 20") Cc: stable <stable@vger.kernel.org> # 3.12 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191210114751.5119-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: gigaset: add endpoint-type sanity check | Johan Hovold | 1 | -0/+12 | |
| Add missing endpoint-type sanity checks to probe. This specifically prevents a warning in USB core on URB submission when fuzzing USB descriptors. Signed-off-by: Johan Hovold <johan@kernel.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191202085610.12719-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
| 2019-12-10 | staging: gigaset: fix illegal free on probe errors | Johan Hovold | 1 | -5/+1 | |
| The driver failed to initialise its receive-buffer pointer, something which could lead to an illegal free on late probe errors. Fix this by making sure to clear all driver data at allocation. Fixes: 2032e2c2309d ("usb_gigaset: code cleanup") Cc: stable <stable@vger.kernel.org> # 2.6.33 Cc: Tilman Schmidt <tilman@imap.cc> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191202085610.12719-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||||
 |
index : linux-dev | |
| Linux kernel development work - see feature branches | Jason A. Donenfeld |
| aboutsummaryrefslogtreecommitdiffstats |