| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
None of these registers is relevant for the userspace API.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the XR17V352 manual, bit 4 is IrDA control and bit 5 for
485. Fortunately, no driver used them so far.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds a new UART port type for TI DA8xx/OMAPL13x/AM17xx/AM18xx/66AK2x.
These SoCs have standard 8250 registers plus some extra non-standard
registers.
The UART will not function unless the non-standard Power and Emulation
Management Register (PWREMU_MGMT) is configured correctly. This is
currently handled in arch/arm/mach-davinci/serial.c for non-device-tree
boards. Making this part of the UART driver will allow UART to work on
device-tree boards as well and the mach code can eventually be removed.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Altera 16550 soft IP UART requires 2 additional registers for
TX FIFO threshold support. These 2 registers enable the TX FIFO
Low Watermark and set the TX FIFO Low Watermark.
Set the TX FIFO threshold to the FIFO size - tx_loadsz.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These have been indirectly included via asm/irqs.h that
has included mach/hardware.h unless SPARSE_IRQ is specified.
Let's move them to where the other OMAP serial defines for
8250 are.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since we have a native 8250 driver carrying the Intel MID serial devices the
specific support is not needed anymore. This patch removes it for Intel MID.
Note that the console device name is changed from ttyMFDx to ttySx.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
-FCR[RTL] = 00 1 byte
-FCR[RTL] = 01 16 bytes
-FCR[RTL] = 10 32 bytes
-FCR[RTL] = 11 56 bytes
-tx_loadsz is set to 63-bytes instead of 64-bytes to implement
workaround of errata A-008006 which states that tx_loadsz should
be configured less than Maximum supported fifo bytes
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch provides mostly a copy of serial8250_tx_dma() +
__dma_tx_complete() with the following extensions:
- DMA bug
At least on AM335x the following problem exists: Even if the TX FIFO is
empty and a TX transfer is programmed (and started) the UART does not
trigger the DMA transfer.
After $TRESHOLD number of bytes have been written to the FIFO manually the
UART reevaluates the whole situation and decides that now there is enough
room in the FIFO and so the transfer begins.
This problem has not been seen on DRA7 or beagle board xm (OMAP3). I am not
sure if this is UART-IP core specific or DMA engine.
The workaround is to use a threshold of one byte, program the DMA
transfer minus one byte and then to put the first byte into the FIFO to
kick start the transfer.
- support for runtime PM
RPM is enabled on start_tx(). We can't disable RPM on DMA complete callback
because there is still data in the FIFO which is being sent. We have to wait
until the FIFO is empty before we disable it.
For this to happen we fake a TX sent error and enable THRI. Once the
FIFO is empty we receive an interrupt and since the TTY-buffer is still
empty we "put RPM" via __stop_tx(). Should it been filed then in the
start_tx() path we should program the DMA transfer and remove the error
flag and the THRI bit.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add tunable RX interrupt trigger I/F of FIFO buffers.
Serial devices are used as not only message communication devices but control
or sending communication devices. For the latter uses, normally small data
will be exchanged, so user applications want to receive data unit as soon as
possible for real-time tendency. If we have a sensor which sends a 1 byte data
each time and must control a device based on the sensor feedback, the RX
interrupt should be triggered for each data.
According to HW specification of serial UART devices, RX interrupt trigger
can be changed, but the trigger is hard-coded. For example, RX interrupt trigger
in 16550A can be set to 1, 4, 8, or 14 bytes for HW, but current driver sets
the trigger to only 8bytes.
This patch makes some devices change RX interrupt trigger from userland.
<How to use>
- Read current setting
# cat /sys/class/tty/ttyS0/rx_trig_bytes
8
- Write user setting
# echo 1 > /sys/class/tty/ttyS0/rx_trig_bytes
# cat /sys/class/tty/ttyS0/rx_trig_bytes
1
<Support uart devices>
- 16550A and Tegra (1, 4, 8, or 14 bytes)
- 16650V2 (8, 16, 24, or 28 bytes)
- 16654 (8, 16, 56, or 60 bytes)
- 16750 (1, 16, 32, or 56 bytes)
<Change log>
Changes in V9:
- Use attr_group instead of dev_spec_attr_group of uart_port structure
Changes in V8:
- Divide this patch from V7's patch based on Greg's comment
Changes in V7:
- Add Documentation
- Change I/F name from rx_int_trig to rx_trig_bytes because the name
rx_int_trig is hard to understand how users specify the value
Changes in V6:
- Move FCR_RX_TRIG_* definition in 8250.h to include/uapi/linux/serial_reg.h,
rename those to UART_FCR_R_TRIG_*, and use UART_FCR_TRIGGER_MASK to
UART_FCR_R_TRIG_BITS()
- Change following function names:
convert_fcr2val() => fcr_get_rxtrig_bytes()
convert_val2rxtrig() => bytes_to_fcr_rxtrig()
- Fix typo in serial8250_do_set_termios()
- Delete the verbose error message pr_info() in bytes_to_fcr_rxtrig()
- Rename *rx_int_trig/rx_trig* to *rxtrig* for several functions or variables
(but UI remains rx_int_trig)
- Change the meaningless variable name 'val' to 'bytes' following functions:
fcr_get_rxtrig_bytes(), bytes_to_fcr_rxtrig(), do_set_rxtrig(),
do_serial8250_set_rxtrig(), and serial8250_set_attr_rxtrig()
- Use up->fcr in order to get rxtrig_bytes instead of rx_trig_raw in
fcr_get_rxtrig_bytes()
- Use conf_type->rxtrig_bytes[0] instead of switch statement for support check
in register_dev_spec_attr_grp()
- Delete the checking whether a user changed FCR or not when minimum buffer
is needed in serial8250_do_set_termios()
Changes in V5.1:
- Fix FCR_RX_TRIG_MAX_STATE definition
Changes in V5:
- Support Tegra, 16650V2, 16654, and 16750
- Store default FCR value to up->fcr when the port is first created
- Add rx_trig_byte[] in uart_config[] for each device and use rx_trig_byte[]
in convert_fcr2val() and convert_val2rxtrig()
Changes in V4:
- Introduce fifo_bug flag in uart_8250_port structure
This is enabled only when parity is enabled and UART_BUG_PARITY is enabled
for up->bugs. If this flag is enabled, user cannot set RX trigger.
- Return -EOPNOTSUPP when it does not support device at convert_fcr2val() and
at convert_val2rxtrig()
- Set the nearest lower RX trigger when users input a meaningless value at
convert_val2rxtrig()
- Check whether p->fcr is existing at serial8250_clear_and_reinit_fifos()
- Set fcr = up->fcr in the begging of serial8250_do_set_termios()
Changes in V3:
- Change I/F from ioctl(2) to sysfs(rx_int_trig)
Changed in V2:
- Use _IOW for TIOCSFIFORTRIG definition
- Pass the interrupt trigger value itself
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UART IRQ Identification bitfield is 3
bits long (bits 3:1) but current mask only
masks 2 bits. Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add register definitions used in several Exar PCI/PCIe UARTs
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for new devices: Exar's XR17V35x family of multi-port PCIe UARTs.
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
|
Jan Kiszka
David Lechner
Thor Thayer
Tony Lindgren
Andy Shevchenko
Vijay Rai
Sebastian Andrzej Siewior
Yoshihiro YUNOMAE
Felipe Balbi
Matt Schulte
David Howells