mlxsw: spectrum: Add support for PAUSE frames

When a packet ingress the switch it's placed in its assigned priority
group (PG) buffer in the port's headroom buffer while it goes through
the switch's pipeline. After going through the pipeline - which
determines its egress port(s) and traffic class - it's moved to the
switch's shared buffer awaiting transmission.

However, some packets are not eligible to enter the shared buffer due to
exceeded quotas or insufficient space. Marking their associated PGs as
lossless will cause the packets to accumulate in the PG buffer. Another
reason for packets accumulation are complicated pipelines (e.g.
involving a lot of ACLs).

To prevent packets from being dropped a user can enable PAUSE frames on
the port. This will mark all the active PGs as lossless and set their
size according to the maximum delay, as it's not configured by user.

                         +----------------+   +
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   | Delay
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   |
    Xon/Xoff threshold   +----------------+   +
                         |                |   |
                         |                |   | 2 * MTU
                         |                |   |
                         +----------------+   +

The delay (612 [Cells]) was calculated according to worst-case scenario
involving maximum MTU and 100m cables.

After marking the PGs as lossless the device is configured to respect
incoming PAUSE frames (Rx PAUSE) and generate PAUSE frames (Tx PAUSE)
according to user's settings.

Whenever the port's headroom configuration changes we take into account
the PAUSE configuration, so that we correctly set the PG's type (lossy /
lossless), size and threshold. This can happen when:

a) The port's MTU changes, as it directly affects the PG's size.

b) A PG is created following user configuration, by binding a priority
to it.

Note that the relevant SUPPORTED flags were already mistakenly set by
the driver before this commit.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 2 insertions, 1 deletions

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_dcb.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_dcb.c
index 257e2d427cab..8786424f6191 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_dcb.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_dcb.c
@@ -142,6 +142,7 @@ static int mlxsw_sp_port_pg_destroy(struct mlxsw_sp_port *mlxsw_sp_port,
 static int mlxsw_sp_port_headroom_set(struct mlxsw_sp_port *mlxsw_sp_port,
 				      struct ieee_ets *ets)
 {
+	bool pause_en = mlxsw_sp_port_is_pause_en(mlxsw_sp_port);
 	struct ieee_ets *my_ets = mlxsw_sp_port->dcb.ets;
 	struct net_device *dev = mlxsw_sp_port->dev;
 	int err;
@@ -150,7 +151,7 @@ static int mlxsw_sp_port_headroom_set(struct mlxsw_sp_port *mlxsw_sp_port,
 	 * traffic is still directed to them.
 	 */
 	err = __mlxsw_sp_port_headroom_set(mlxsw_sp_port, dev->mtu,
-					   ets->prio_tc);
+					   ets->prio_tc, pause_en);
 	if (err) {
 		netdev_err(dev, "Failed to configure port's headroom\n");
 		return err;