ath10k: add support for hardware rfkill

When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath10k will check the capability, and if it is enabled then
ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio
and also notifies cfg80211.

We can't power off the device when rfkill is enabled, as otherwise the
firmware would not be able to detect GPIO changes and report them to the
host. So when rfkill is enabled, we need to keep the firmware running.

Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1.

Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

1 files changed, 49 insertions, 0 deletions

diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
index 2432a7434289..69a1ec53df29 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -409,6 +409,49 @@ static int ath10k_wmi_tlv_event_tx_pause(struct ath10k *ar,
 	return 0;
 }
 
+static void ath10k_wmi_tlv_event_rfkill_state_change(struct ath10k *ar,
+						     struct sk_buff *skb)
+{
+	const struct wmi_tlv_rfkill_state_change_ev *ev;
+	const void **tb;
+	bool radio;
+	int ret;
+
+	tb = ath10k_wmi_tlv_parse_alloc(ar, skb->data, skb->len, GFP_ATOMIC);
+	if (IS_ERR(tb)) {
+		ret = PTR_ERR(tb);
+		ath10k_warn(ar,
+			    "failed to parse rfkill state change event: %d\n",
+			    ret);
+		return;
+	}
+
+	ev = tb[WMI_TLV_TAG_STRUCT_RFKILL_EVENT];
+	if (!ev) {
+		kfree(tb);
+		return;
+	}
+
+	ath10k_dbg(ar, ATH10K_DBG_MAC,
+		   "wmi tlv rfkill state change gpio %d type %d radio_state %d\n",
+		   __le32_to_cpu(ev->gpio_pin_num),
+		   __le32_to_cpu(ev->int_type),
+		   __le32_to_cpu(ev->radio_state));
+
+	radio = (__le32_to_cpu(ev->radio_state) == WMI_TLV_RFKILL_RADIO_STATE_ON);
+
+	spin_lock_bh(&ar->data_lock);
+
+	if (!radio)
+		ar->hw_rfkill_on = true;
+
+	spin_unlock_bh(&ar->data_lock);
+
+	/* notify cfg80211 radio state change */
+	ath10k_mac_rfkill_enable_radio(ar, radio);
+	wiphy_rfkill_set_hw_state(ar->hw->wiphy, !radio);
+}
+
 static int ath10k_wmi_tlv_event_temperature(struct ath10k *ar,
 					    struct sk_buff *skb)
 {
@@ -629,6 +672,9 @@ static void ath10k_wmi_tlv_op_rx(struct ath10k *ar, struct sk_buff *skb)
 	case WMI_TLV_TX_PAUSE_EVENTID:
 		ath10k_wmi_tlv_event_tx_pause(ar, skb);
 		break;
+	case WMI_TLV_RFKILL_STATE_CHANGE_EVENTID:
+		ath10k_wmi_tlv_event_rfkill_state_change(ar, skb);
+		break;
 	case WMI_TLV_PDEV_TEMPERATURE_EVENTID:
 		ath10k_wmi_tlv_event_temperature(ar, skb);
 		break;
@@ -1215,6 +1261,7 @@ static int ath10k_wmi_tlv_op_pull_svc_rdy_ev(struct ath10k *ar,
 	arg->num_mem_reqs = ev->num_mem_reqs;
 	arg->service_map = svc_bmap;
 	arg->service_map_len = ath10k_wmi_tlv_len(svc_bmap);
+	arg->sys_cap_info = ev->sys_cap_info;
 
 	ret = ath10k_wmi_tlv_iter(ar, mem_reqs, ath10k_wmi_tlv_len(mem_reqs),
 				  ath10k_wmi_tlv_parse_mem_reqs, arg);
@@ -4214,6 +4261,8 @@ static struct wmi_pdev_param_map wmi_tlv_pdev_param_map = {
 	.wapi_mbssid_offset = WMI_PDEV_PARAM_UNSUPPORTED,
 	.arp_srcaddr = WMI_PDEV_PARAM_UNSUPPORTED,
 	.arp_dstaddr = WMI_PDEV_PARAM_UNSUPPORTED,
+	.rfkill_config = WMI_TLV_PDEV_PARAM_HW_RFKILL_CONFIG,
+	.rfkill_enable = WMI_TLV_PDEV_PARAM_RFKILL_ENABLE,
 };
 
 static struct wmi_peer_param_map wmi_tlv_peer_param_map = {