| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Merge in late fixes to prepare for the 6.16 net-next PR.
No conflicts nor adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove lan743x_phy_init from lan743x_hardware_init as it resets the PHY
registers, causing WOL to fail on subsequent attempts. Add a call to
lan743x_hw_reset_phy in the probe function to ensure the PHY is reset
during device initialization.
Fixes: 23f0703c125be ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250526053048.287095-3-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rename the function to lan743x_hw_reset_phy to better describe it
operation.
Fixes: 23f0703c125be ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250526053048.287095-2-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.15-rc8).
Conflicts:
80f2ab46c2ee ("irdma: free iwdev->rf after removing MSI-X")
4bcc063939a5 ("ice, irdma: fix an off by one in error handling code")
c24a65b6a27c ("iidc/ice/irdma: Update IDC to support multiple consumers")
https://lore.kernel.org/20250513130630.280ee6c5@canb.auug.org.au
No extra adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SGMII_CTRL register, which specifies the active interface, was not
properly restored when resuming from suspend. This led to incorrect
interface selection after resume particularly in scenarios involving
the FPGA.
To fix this:
- Move the SGMII_CTRL setup out of the probe function.
- Initialize the register in the hardware initialization helper function,
which is called during both device initialization and resume.
This ensures the interface configuration is consistently restored after
suspend/resume cycles.
Fixes: a46d9d37c4f4f ("net: lan743x: Add support for SGMII interface")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Link: https://patch.msgid.link/20250516035719.117960-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Permit programs such as "hwtstamp_ctl -i eth0" to retrieve the current
timestamping configuration of the NIC, rather than returning "Device
driver does not have support for non-destructive SIOCGHWTSTAMP."
The driver configures all channels with the same timestamping settings.
On TX, retrieve the settings of the first channel, those should be
representative for the entire NIC. On RX, save the filter settings in a
new adapter field.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250514151931.1988047-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
New timestamping API was introduced in commit 66f7223039c0 ("net: add
NDOs for configuring hardware timestamping") from kernel v6.6.
It is time to convert the lan743x driver to the new API, so that
timestamping configuration can be removed from the ndo_eth_ioctl()
path completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250514151931.1988047-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.15-rc5).
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver allocates ring elements using GFP_DMA flags. There is
no dependency from LAN743x hardware on memory allocation should be
in DMA_ZONE. Hence modifying the flags to use only GFP_ATOMIC. This
is consistent with other callers of lan743x_rx_init_ring_element().
Reported-by: Zhang, Liyin(CN) <Liyin.Zhang.CN@windriver.com>
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250415044509.6695-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert lan743x to phylink managed EEE:
- Set the lpi_capabilties.
- Move the call to lan743x_mac_eee_enable() into the enable/disable
tx_lpi functions.
- Ensure that EEEEN is clear during probe.
- Move the setting of the LPI timer into mac_enable_tx_lpi().
- Move reading of LPI timer to phylink initialisation to set the
default timer value.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYAEB-0014QB-4s@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the netdev that we already have in lan743x_phylink_mac_link_down().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYAE5-0014Q5-Up@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to ethtool phylink functions:
- get/set settings like speed, duplex etc
- get/set the wake-on-lan (WOL)
- get/set the energy-efficient ethernet (EEE)
- get/set the pause
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Migrate phy support from phylib to phylink.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create separate Link Speed Duplex (LSD) update state function from
lan743x_sgmii_config () to use as subroutine.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create separate PCS power reset function from lan743x_sgmii_config () to use
as subroutine.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent options not supported by the PHY from being requested to it by the MAC
Whenever a WOL option is supported by both, the PHY is given priority
since that usually leads to better power savings.
Fixes: e9e13b6adc33 ("lan743x: fix for potential NULL pointer dereference with bare card")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When Wake-on-LAN (WoL) is active and the system is in suspend mode, triggering
a system event can wake the system from sleep, which may block the data path.
To restore normal data path functionality after waking, disable all wake-up
events. Furthermore, clear all Write 1 to Clear (W1C) status bits by writing
1's to them.
Fixes: 4d94282afd95 ("lan743x: Add power management support")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c94510 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct spelling in comments, as flagged by codespell.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/20240424-lan743x-confirm-v2-1-f0480542e39f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enabling/disabling of EEE in the MAC should happen as a result of
auto negotiation. So move the enable/disable into
lan743x_phy_link_status_change() which gets called by phylib when
there is a change in link status.
lan743x_ethtool_set_eee() now just programs the hardware with the LTI
timer value, and passed everything else to phylib, so it can correctly
setup the PHY.
lan743x_ethtool_get_eee() relies on phylib doing most of the work, the
MAC driver just adds the LTI timer value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PCI11x1x Rev B0 devices might drop packets when receiving back to back frames
at 2.5G link speed. Change the B0 Rev device's Receive filtering Engine FIFO
threshold parameter from its hardware default of 4 to 3 dwords to prevent the
problem. Rev C0 and later hardware already defaults to 3 dwords.
Fixes: bb4f6bffe33c ("net: lan743x: Add PCI11010 / PCI11414 device IDs")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326065805.686128-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is a spelling mistake in a netif_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220091737.2676984-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently all RX frames are timestamped which results in a performance
penalty when timestamping is not needed. The default is now being
changed to not timestamp any Rx frames (HWTSTAMP_FILTER_NONE), but
support has been added to allow changing the desired RX timestamping
mode (HWTSTAMP_FILTER_ALL - which was the previous setting and
HWTSTAMP_FILTER_PTP_V2_EVENT are now supported) using
SIOCSHWTSTAMP. All settings were tested using the hwstamp_ctl application.
It is also noted that ptp4l, when started, preconfigures the device to
timestamp using HWTSTAMP_FILTER_PTP_V2_EVENT, so this driver continues
to work properly "out of the box".
Test setup: x64 PC with LAN7430 ---> x64 PC as partner
iperf3 with - Timestamp all incoming packets:
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.05 sec 517 MBytes 859 Mbits/sec 0 sender
[ 5] 0.00-5.00 sec 515 MBytes 864 Mbits/sec receiver
iperf Done.
iperf3 with - Timestamp only PTP packets:
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.04 sec 563 MBytes 937 Mbits/sec 0 sender
[ 5] 0.00-5.00 sec 561 MBytes 941 Mbits/sec receiver
Signed-off-by: Vishvambar Panth S <vishvambarpanth.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231020185801.25649-1-vishvambarpanth.s@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When operating in fixed phy mode and if there is repeated open/close
phy test cases, everytime the fixed phy is registered as a new phy
which leads to overrun after 32 iterations. It is solved by adding
fixed_phy_unregister() in the phy_close path.
In phy_close path, netdev->phydev cannot be used directly in
fixed_phy_unregister() due to two reasons,
- netdev->phydev is set to NULL in phy_disconnect()
- fixed_phy_unregister() can be called only after phy_disconnect()
So saving the netdev->phydev in local variable 'phydev' and
passing it to phy_disconnect().
Signed-off-by: Pavithra Sathyanarayanan <Pavithra.Sathyanarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fixed_phy_register() returns -EPROBE_DEFER, -EINVAL and -EBUSY,
etc, in addition to -EIO. The Best practice is to return these
error codes with PTR_ERR().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_set_rx_mode() grabs a spin_lock, and the lan743x implementation
proceeds subsequently to go to sleep using readx_poll_timeout().
Introduce a helper wrapping the readx_poll_timeout_atomic() function
and use it to replace the calls to readx_polL_timeout().
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Cc: stable@vger.kernel.org
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230627035000.1295254-1-moritzf@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Simplify comparison, no functional changes.
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Moritz Fischer <moritzf@google.com>
Link: https://lore.kernel.org/r/20230627035432.1296760-1-moritzf@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The gotos for cleanup aren't required, the function
might as well just return the actual error code.
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_disconnect() calls phy_detach() which already clears 'phydev' if it
is attached to a struct net_device.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230321131745.27688-1-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Deciding if to probe of PHYs using C45 is now determine by if the bus
provides the C45 read method. This makes probe_capabilities redundant
so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add fixed_phy support at 1Gbps full duplex for the lan7431 device
if a phy not found over MDIO. Tested with a MAC to MAC connection
from LAN7431 to a KSZ9893 switch. This avoids the Driver open error
in LAN743x. TX delay and internal CLK125 generation is already
enabled in EEPROM.
Signed-off-by: Pavithra Sathyanarayanan <Pavithra.Sathyanarayanan@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add logic to read the Phy interface from MAC_CR register for LAN743x
driver.
Checks for the LAN7430/31 or pci11x1x devices and the adapter
interface is updated accordingly. For LAN7431, adapter interface is set
based on Bit 19 of MAC_CR register as MII or RGMII which removes the
forced RGMII/GMII configurations in lan743x_phy_open().
Signed-off-by: Pavithra Sathyanarayanan <Pavithra.Sathyanarayanan@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove the MII/RGMII Selection settings in driver as it is preset
by the EEPROM and has the required configurations before the driver
loads for LAN743x.
Signed-off-by: Pavithra Sathyanarayanan <Pavithra.Sathyanarayanan@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The microchip lan743x MDIO bus driver can perform both C22 and C45
transfers in some variants. Create separate functions for each and
register the C45 versions using the new API calls where appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to SGMII register dump
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add pause get and set functions
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add Rx IP and TCP checksum offload
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Fix to use multiqueue start/stop APIs
- Change to return NETDEV_TX_BUSY instead of holding the TX skb when busy
- Increase Tx ring size to 128 to address performance issues in some platforms
- Use NAPI_POLL_WEIGHT for Tx Napi handler instead of ring dependent value
- Use multiqueue to register 4 Rx channels
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a copy and paste bug in lan743x_sgmii_config() so it checks
if (ret < 0) instead of if (mii_ctl < 0).
Fixes: 46b777ad9a8c ("net: lan743x: Add support to SGMII 1G and 2.5G")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/YrRry7K66BzKezl8@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add SGMII access read and write functions
Add support to SGMII 1G and 2.5G for PCI11010/PCI11414 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to Magic Packet Detection with Secure-ON for PCI11010/PCI11414 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the MDIO interface declarations to reflect what is currently supported by
the PCI11010 / PCI11414 devices (C22 for RGMII and C22_C45 for SGMII)
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the drivers with custom tx napi weight call netif_napi_add_tx_weight().
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220504163725.550782-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add new the EEPROM read and write access functions and system lock
protection to access by devices for PCI11010/PCI11414 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx 4 queue statistics display through ethtool application
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for Clause-45 MDIO PHY management
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change facilitates the selection between SGMII and (R)GIII
interfaces
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase MSI / MSI-X vectors supported from 8 to 16 and
Interrupt De-assertion timers from 8 to 10
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Paolo Abeni
Thangaraj Samynathan
Jakub Kicinski
Vladimir Oltean
Russell King (Oracle)
Raju Lakkaraju
Eric Dumazet
Simon Horman
Andrew Lunn
Colin Ian King
Vishvambar Panth S
Pavithra Sathyanarayanan
Ruan Jinjie
Moritz Fischer
Wolfram Sang
Dan Carpenter