| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
- When MSI is enabled but iMSI-RX is not used, configure AXIINTC to allow
GIT ITS to handle MSI (Marek Vasut)
- Refactor GIC600 implementation to make it easier to add platforms that
only support 32-bit addressing (Marek Vasut)
- Add Renesas R-Car Gen4 S4/V4H/V4M to the list of GIC600 integrations that
only support 32-bit addressing (Marek Vasut)
* pci/controller/dwc-rcar-gen4:
irqchip/gic-v3: Add Renesas R-Car Gen4 erratum workaround
irqchip/gic-v3: Refactor GIC600 limited to 32bit PA erratum handling
PCI: rcar-gen4: Configure AXIINTC if iMSI-RX is not used
PCI: dwc: Move iMSI-RX check before calling 'pp->ops->init()'
|
|
- Remove PERST# checking from pci_host_common_parse_port() so callers can
decide whether to fall back to legacy DT binding with PERST# in the host
bridge (Sherry Sun)
- Fix build issues when PCI_PWRCTRL_GENERIC or PCI_HOST_COMMON is a module
(Arnd Bergmann)
- Create pwrctrl devices only once by doing it from imx_pcie_probe()
instead of imx_pcie_host_init(), which is used during both probe and
resume (Sherry Sun)
- Use 'dw_pcie_rp->skip_pwrctrl_off' to avoid powering off devices during
suspend to preserve wakeup capability (Sherry Sun)
- Add runtime PM support for i.MX95 to allow dynamic power management when
the link is idle (Richard Zhu)
* pci/controller/dwc-imx6:
PCI: imx6: Add runtime PM support for i.MX95
PCI: imx6: Add 'skip_pwrctrl_off' flag support
PCI: imx6: Move pci_pwrctrl_create_devices() to imx_pcie_probe()
PCI: imx6: Fix building against PCI_PWRCTRL_GENERIC
PCI: imx6: Fix building against PCI_HOST_COMMON
PCI: host-generic: Move legacy DT binding fallback decision to caller of pci_host_common_parse_ports()
|
|
The PCIe link may go down in cases like firmware crashes or unstable
connections. When this occurs, the Root Port must be reset to restore the
functionality. However, the current driver lacks link down handling,
forcing users to reboot the system to recover.
Implement the .reset_root_port() callback for link down handling for the
Rockchip DWC PCIe host controller. The RC is reset, reconfigured, and link
training initiated to recover from the link down event.
This also by extension fixes issues with sysfs-initiated bus resets.
Currently, the endpoint device is non-functional after a sysfs initiated
bus reset (it may link up with downgraded link status). With the link down
handling support, a sysfs initiated bus reset works as intended. Testing
conducted on a ROCK5B board with an M.2 NVMe drive.
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
[bhelgaas: subject]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260727172654.605988-4-cassel@kernel.org
|
|
When MSI is enabled but the DWC built-in iMSI-RX is not used, MSI must
be handled via the GIC ITS. Configure all controller MSI registers
accordingly.
Set or clear the MSICAP0 MSIE bit and the PCIEINTSTS0EN MSI_CTRL_INT
bit based on the MSI enable state. Set both bits when MSI is enabled.
Clear both bits when MSI is disabled.
When MSI is disabled, or when MSI is enabled together with iMSI-RX,
clear AXIINTCADDR and AXIINTCCONT to disable any pass through of MSI
TLPs onto the AXI bus and further into the GIC ITS translation
registers.
When MSI is enabled and iMSI-RX is not used, program AXIINTCADDR with
the target address of the GIC ITS translation register, and program
AXIINTCCONT to enable MSI TLP pass through onto the AXI bus and into
the GIC ITS. This configuration allows the GIC ITS to handle MSI
instead of the integrated iMSI-RX.
The driver includes linux/irqchip/arm-gic-v3.h which pulls in headers
which are available only on ARM and ARM64, on other architectures the
headers are not present and the driver fails to build. This driver is
used only on ARM64 hardware, so isolate its build only to ARM64 to avoid
build failures on other architectures.
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[mani: commit log and squashed the Kconfig fix:
https://patch.msgid.link/20260714131957.38067-1-marek.vasut+renesas@mailbox.org]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260707203743.88299-3-marek.vasut+renesas@mailbox.org
|
|
When endpoint mode is built-in, but pwrctrl support is in a loadable
module, the imx driver fails to build because the unused host
support still tries to link against pwrctrl:
ld.lld: error: undefined symbol: pci_pwrctrl_power_off_devices
>>> referenced by pci-imx6.c:1988 (drivers/pci/controller/dwc/pci-imx6.c:1988)
>>> drivers/pci/controller/dwc/pci-imx6.o:(imx_pcie_shutdown) in archive vmlinux.a
Add one more select for this.
Fixes: 85c1fcfa740d ("PCI: imx6: Integrate new pwrctrl API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://patch.msgid.link/20260618143629.2035247-1-arnd@kernel.org
|
|
When CONFIG_PCI_HOST_COMMON is set to =m, the i.MX6 PCIe driver
fails to link. This can happen when only i.MX endpoint mode is
enabled but not host mode, which would indirectly enable the
host-common driver itself.
ld.lld: error: undefined symbol: pci_host_common_parse_ports
>>> referenced by pci-imx6.c
>>> drivers/pci/controller/dwc/pci-imx6.o:(imx_pcie_host_init) in archive vmlinux.a
ld.lld: error: undefined symbol: pci_host_common_delete_ports
>>> referenced by pci-imx6.c
>>> drivers/pci/controller/dwc/pci-imx6.o:(imx_pcie_host_init) in archive vmlinux.a
>>> referenced by pci-imx6.c
>>> drivers/pci/controller/dwc/pci-imx6.o:(imx_pcie_host_init) in archive vmlinux.a
Select the common module from the endpoint support directly.
Fixes: 250eea5c06f5 ("PCI: imx6: Parse 'reset-gpios' in Root Port nodes")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260616164049.3656435-1-arnd@kernel.org
|
|
- Add UltraRISC DP1000 PCIe controller DT binding and driver (Jia Wang)
* pci/controller/dwc-ultrarisc:
PCI: ultrarisc: Add UltraRISC DP1000 PCIe Root Complex driver
dt-bindings: PCI: Add UltraRISC DP1000 PCIe controller
|
|
Integrate the PCI pwrctrl framework into the pci-imx6 driver to provide
standardized power management for PCI devices.
Legacy regulator handling (vpcie-supply at controller level) is maintained
for backward compatibility with existing device trees. New device trees
should specify power supplies at the Root Port level to utilize the pwrctrl
framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260520084904.2424253-2-sherry.sun@oss.nxp.com
|
|
Add DP1000 SoC PCIe Root Complex driver.
The controller only supports 32-bit aligned configuration space accesses.
Signed-off-by: Xincheng Zhang <zhangxincheng@ultrarisc.com>
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
[mani: changed to builtin_platform_driver() to prevent irqchip removal]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: squash MAINTAINERS update here]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260427-ultrarisc-pcie-v4-3-98935f6cdfb5@ultrarisc.com
|
|
- Allow Layerscape host controller driver to be build as a removable module
(Sascha Hauer)
* pci/controller/dwc-layerscape:
PCI: layerscape: Allow to compile as module
|
|
- Add DT binding and driver for ESWIN PCIe Root Complex (Senchuan Zhang)
* pci/controller/dwc-eswin:
PCI: eswin: Add ESWIN PCIe Root Complex driver
dt-bindings: PCI: eswin: Add ESWIN PCIe Root Complex
# Conflicts:
# drivers/pci/controller/dwc/Kconfig
# drivers/pci/controller/dwc/Makefile
|
|
- Add Andes QiLai SoC PCIe host driver support (Randolph Lin)
* pci/controller/dwc-andes-qilai:
PCI: qilai: Add Andes QiLai SoC PCIe host driver support
dt-bindings: PCI: Add Andes QiLai PCIe support
# Conflicts:
# drivers/pci/controller/dwc/Makefile
|
|
- Continue with system suspend even if an Endpoint doesn't respond with
PME_TO_Ack message (Manivannan Sadhasivam)
- Remove the Baikal-T1 controller driver since it never quite became usable
(Andy Shevchenko)
- Set Endpoint MSI-X Table Size in the correct function of a multi-function
device when configuring MSI-X, not in Function 0 (Aksh Garg)
- Set Max Link Width and Max Link Speed for all functions of a
multi-function device, not just Function 0 (Aksh Garg)
- Clean up in the dw_pcie_resume_noirq() error path (Manivannan Sadhasivam)
- Expose PCIe event counters in groups 5-7 in debugfs (Hans Zhang)
- Fix type mismatch for kstrtou32_from_user() in debugfs write functions
(Hans Zhang)
* pci/controller/dwc:
PCI: dwc: Fix type mismatch for kstrtou32_from_user() return value
PCI: dwc: Expose PCIe event counters for groups 5 to 7 over debugfs
PCI: dwc: Perform cleanup in the error path of dw_pcie_resume_noirq()
PCI: dwc: ep: Mirror the max link width and speed fields to all functions
PCI: dwc: ep: Fix MSI-X Table Size configuration in dw_pcie_ep_set_msix()
PCI: dwc: Remove not-going-to-be-supported code for Baikal SoC
PCI: dwc: Proceed with system suspend even if the endpoint doesn't respond with PME_TO_Ack message
|
|
Add driver for the ESWIN PCIe Root Complex based on the DesignWare PCIe
core, IP revision 5.96a. The PCIe Gen.3 Root Complex supports data rate of
8 GT/s and x4 lanes, with INTx and MSI interrupt capability.
Signed-off-by: Yu Ning <ningyu@eswincomputing.com>
Signed-off-by: Yanghui Ou <ouyanghui@eswincomputing.com>
Signed-off-by: Senchuan Zhang <zhangsenchuan@eswincomputing.com>
[mani: renamed "EIC7700" to "ESWIN", added maintainers entry, removed async probe]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: add driver tag in subject]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260227111808.1996-1-zhangsenchuan@eswincomputing.com
|
|
The driver is pretty generic and would fit for either PCI Slots or
endpoints connected to PCI ports, so rename the driver and module as
pci-pwrctrl-generic.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260220-topic-sm8650-ayaneo-pocket-s2-base-v5-3-1ad79caa1efa@linaro.org
|
|
Add driver support for DesignWare based PCIe controller in Andes
QiLai SoC. The driver only supports the Root Complex mode.
Signed-off-by: Randolph Lin <randolph@andestech.com>
[mani: squashed the MAINTAINERS change]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260225085504.3757601-4-randolph@andestech.com
|
|
As noticed in the discussion [1] the Baikal SoC and platforms
are not going to be finalized, hence remove stale code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/lkml/22b92ddf-6321-41b5-8073-f9c7064d3432@infradead.org/ [1]
Link: https://patch.msgid.link/20260220142600.2397070-1-andriy.shevchenko@linux.intel.com
|
|
The layerscape pcie host controller could also be compiled as module.
Add the necessary infrastructure to allow building as module instead of
only as builtin driver.
Since the driver doesn't expose an irqchip controller, it is also safe to
be removed during runtime.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[mani: added a note about driver removability]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Link: https://patch.msgid.link/20260112-v6-19-topic-layerscape-pcie-v1-1-1cd863fce50e@pengutronix.de
|
|
Replace ARCH_TEGRA_194_SOC dependency with a more generic ARCH_TEGRA check
for the Tegra194 PCIe controller, allowing it to be built on Tegra
platforms beyond Tegra194. Additionally, ensure compatibility by requiring
ARM64 or COMPILE_TEST since this driver works only for ARM64 Tegra SoCs.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[mani: moved ARM64 dependency to ARCH_TEGRA]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Acked-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20250508051922.4134041-1-vidyas@nvidia.com
|
|
- Add DT binding and driver for SpacemiT K1 (Alex Elder)
* pci/controller/spacemit-k1:
PCI: spacemit: Add SpacemiT PCIe host driver
dt-bindings: pci: spacemit: Introduce PCIe host controller
|
|
- Add NXP S32G host controller DT binding and driver (Vincent Guittot)
* pci/controller/s32g:
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
|
|
Add initial support of the PCIe controller for the NXP S32G SoC family.
Only host mode is supported.
Co-developed-by: Ionut Vicovan <Ionut.Vicovan@nxp.com>
Signed-off-by: Ionut Vicovan <Ionut.Vicovan@nxp.com>
Co-developed-by: Ciprian Marian Costea <ciprianmarian.costea@nxp.com>
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@nxp.com>
Co-developed-by: Ghennadi Procopciuc <Ghennadi.Procopciuc@nxp.com>
Signed-off-by: Ghennadi Procopciuc <Ghennadi.Procopciuc@nxp.com>
Co-developed-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
[mani: replaced memblock_start_of_DRAM with hardcoded boundary addr]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251121164920.2008569-4-vincent.guittot@linaro.org
|
|
Introduce a driver for the PCIe host controller found in the SpacemiT K1
SoC. The hardware is derived from the Synopsys DesignWare PCIe IP. The
driver supports up to three PCIe ports operating at PCIe link speed up to
5 GT/s. The first port uses a combo PHY, which may be configured for use
for USB3 instead.
Signed-off-by: Alex Elder <elder@riscstar.com>
[mani: added FIXME to the comment on disabling ASPM L1]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Jason Montleon <jmontleo@redhat.com>
Tested-by: Johannes Erdfelt <johannes@erdfelt.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Link: https://patch.msgid.link/20251113214540.2623070-6-elder@riscstar.com
|
|
The 'pci-keystone.c' driver is the application/glue/wrapper driver for the
Designware PCIe Controllers on TI SoCs. Now that all of the helper APIs
that the 'pci-keystone.c' driver depends upon have been exported for use,
enable support to build the driver as a loadable module.
When building the driver as a module, the functions marked by the '__init'
keyword may be invoked after the init memory has been freed by the kernel.
This results will result in an exception of the form:
Unable to handle kernel paging request at virtual address ...
Mem abort info:
...
pc : ks_pcie_host_init+0x0/0x540
lr : dw_pcie_host_init+0x170/0x498
...
ks_pcie_host_init+0x0/0x540 (P)
ks_pcie_probe+0x728/0x84c
platform_probe+0x5c/0x98
really_probe+0xbc/0x29c
__driver_probe_device+0x78/0x12c
driver_probe_device+0xd8/0x15c
To address this, introduce a new function namely 'ks_pcie_init()' to
register the 'fault handler' while removing the '__init' keyword from
existing functions.
Note that hook_fault_code() is defined as '__init' function. Since the init
functions should never be called during runtime (after init memory freeing
stage), the driver is made as a built-in if CONFIG_ARM (where
hook_fault_code() is used) is selected.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[mani: added a note about hook_fault_code()]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251029080547.1253757-5-s-vadapalli@ti.com
|
|
- Update pinctrl documentation of initial states and use in runtime
suspend/resume (Christian Bruel)
- Add pinctrl_pm_select_init_state() for use by stm32 driver, which needs
it during resume (Christian Bruel)
- Add devicetree bindings and drivers for the STMicroelectronics STM32MP25
in host and endpoint modes (Christian Bruel)
* pci/controller/stm32:
MAINTAINERS: Add entry for ST STM32MP25 PCIe drivers
PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
PCI: stm32: Add PCIe host support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Root Complex bindings
pinctrl: Add pinctrl_pm_select_init_state helper function
Documentation: pinctrl: Describe PM helper functions for standard states.
|
|
Add driver to configure the STM32MP25 SoC PCIe controller based on the
DesignWare PCIe core in endpoint mode. Controller support 2.5 and 5 GT/s
data rates and uses the common reference clock provided by the host.
The PCIe core_clk receives the pipe0_clk from the ComboPHY as input,
and the ComboPHY PLL must be locked for pipe0_clk to be ready.
Consequently, PCIe core registers cannot be accessed until the ComboPHY is
fully initialised and REFCLK is enabled and ready.
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
[mani: reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: squash in https://patch.msgid.link/20250902122641.269725-1-christian.bruel@foss.st.com
to remove redundant link_status checks]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250820075411.1178729-7-christian.bruel@foss.st.com
|
|
Add driver for the STM32MP25 SoC PCIe controller based on the DesignWare
PCIe core. Controller supports 2.5 and 5 GT/s data rates, MSI via GICv2m,
Single Virtual Channel, Single Function and WAKE# GPIO.
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
[mani: reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: squash error handling cleanup from Christophe JAILLET
<christophe.jaillet@wanadoo.fr>:
https://patch.msgid.link/e69ade3edcec4da2d5bfc66e0d03bbcb5a857021.1759169956.git.christophe.jaillet@wanadoo.fr]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250820075411.1178729-5-christian.bruel@foss.st.com
|
|
In order to enable PCIe ECAM mechanism in DWC driver as per the 'CFG Shift
Feature' documented in Designware databook r5.20a, sec 3.10.10.3, prepare
the driver to handle the one time iATU setup and creating ECAM window.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: splitted the preparatory code into a separate commit for bisectability]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250923-controller-dwc-ecam-v10-2-e84390ba75fa@kernel.org
|
|
Select the pwrctrl driver, which is utilized to manage the power supplies
of the devices connected to the standard PCI slots conforming to
specification like PCIe CEM. This ensures that the voltage rails of the
standard PCI slots on some platforms eg. X1E80100-QCP can be correctly
turned on/off if they are described in PCIe Root Port device tree node.
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250722091151.1423332-2-quic_wenbyao@quicinc.com
|
|
- Add DT binding and driver for Sophgo SG2044 PCIe controller driver in
Root Complex mode (Inochi Amaoto)
* pci/controller/sophgo:
PCI: dwc: Add Sophgo SG2044 PCIe controller driver in Root Complex mode
dt-bindings: pci: Add Sophgo SG2044 PCIe host
|
|
- Export DWC MSI controller related APIs for use by upcoming DWC-based ECAM
implementation (Mayank Rana)
- Rename gen_pci_init() to pci_host_common_ecam_create() and export for use
by controller drivers (Mayank Rana)
- Add DT binding and driver support for SA8255p, which supports ECAM for
Configuration Space access (Mayank Rana)
- Update DT binding and driver to describe PHYs and per-Root Port resets in
a Root Port stanza and deprecate describing them in the host bridge; this
makes it possible to support multiple Root Ports in the future (Krishna
Chaitanya Chundru)
* pci/controller/qcom:
PCI: qcom: Add support for parsing the new Root Port binding
dt-bindings: PCI: qcom: Move PHY & reset GPIO to Root Port node
PCI: qcom: Add support for Qualcomm SA8255p based PCIe Root Complex
dt-bindings: PCI: qcom,pcie-sa8255p: Document ECAM compliant PCIe root complex
PCI: host-generic: Rename and export gen_pci_init() for PCIe controller drivers
PCI: dwc: Export DWC MSI controller related APIs
|
|
Add driver support for DesignWare based PCIe controller in SG2044 SoC. The
driver currently supports the Root Complex mode.
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
[mani: renamed the driver to 'pcie-sophgo.c' and Kconfig fix]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: whitespace]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250504004420.202685-3-inochiama@gmail.com
|
|
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/04d4a96046490e50139826c16423954e033cdf89.1750858083.git.namcao@linutronix.de
|
|
Add functionality to enable resource management (like clocks, regulators,
PHY) through firmware and enumerate ECAM compliant Root Complex on SA8255p
SoC, where the PCIe Root Complex is firmware managed and configured into
ECAM compliant mode.
Signed-off-by: Mayank Rana <mayank.rana@oss.qualcomm.com>
[mani: minor code cleanups and commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: add "ECAM" in comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250616224259.3549811-5-mayank.rana@oss.qualcomm.com
|
|
- Move struct dwc_pcie_vsec_id to include/linux/pcie-dwc.h, where it can be
shared by debugfs, perf, sysfs, etc (Manivannan Sadhasivam)
- Add dw_pcie_find_vsec_capability() to locate Vendor Specific Extended
Capabilities (Shradha Todi)
- Add debugfs-based Silicon Debug, Error Injection, Statistical Counter
support for DWC (Shradha Todi)
- Add debugfs property to expose LTSSM status of DWC PCIe link (Hans Zhang)
- Add Rockchip Vendor ID and Vendor Specific ID of RAS DES Capability so
the DWC debugfs features work for Rockchip as well (Niklas Cassel)
* pci/controller/dwc:
PCI: dw-rockchip: Hide broken ATS capability for RK3588 running in EP mode
PCI: dwc: ep: Add dw_pcie_ep_hide_ext_capability()
PCI: dwc: ep: Return -ENOMEM for allocation failures
PCI: dwc: Add Rockchip to the RAS DES allowed vendor list
PCI: Add Rockchip Vendor ID
PCI: dwc: Add debugfs property to provide LTSSM status of the PCIe link
PCI: dwc: Add debugfs based Statistical Counter support for DWC
PCI: dwc: Add debugfs based Error Injection support for DWC
PCI: dwc: Add debugfs based Silicon Debug support for DWC
PCI: dwc: Add helper to find the Vendor Specific Extended Capability (VSEC)
perf/dwc_pcie: Move common DWC struct definitions to 'pcie-dwc.h'
|
|
Add support for AMD MDB (Multimedia DMA Bridge) IP core as Root Port.
The Versal2 devices include MDB Module. The integrated block for MDB
along with the integrated bridge can function as PCIe Root Port
controller at Gen5 32-GT/s operation per lane.
Bridge supports error and INTx interrupts and are handled using platform
specific interrupt line in Versal2.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250228093351.923615-4-thippeswamy.havalige@amd.com
[bhelgaas: only present on ARM64-based SoCs; squash Kconfig dependency on
ARM64 from Geert Uytterhoeven <geert+renesas@glider.be>:
https://lore.kernel.org/r/eaef1dea7edcf146aa377d5e5c5c85a76ff56bae.1742306383.git.geert+renesas@glider.be]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: commit log, code comments and error messages clean-up,
drop redundant "depends on PCI" from Kconfig, expose the error code
as part of error messages where appropriatie, change "depends on"
expression to match existing style from other drivers]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Add support to provide Silicon Debug interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-4-shradha.t@samsung.com
[kwilczynski: commit log, tidy up Kconfig and drop "default y", tidy up
code comments, squashed patch that fixes a NULL pointer dereference when
debugfs is already unavailable during clean-up from
https://lore.kernel.org/linux-pci/20250225171239.19574-2-manivannan.sadhasivam@linaro.org,
refactor dwc_pcie_debugfs_init() to not return errors, squashed patch that
changes how lack of the RAS DES capability is handled from
https://lore.kernel.org/linux-pci/20250304151814.6xu7cbpwpqrvcad5@thinkpad]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
During high data transmission rates such as 16.0 GT/s, there is an
increased risk of signal loss due to poor channel quality and
interference. This can impact receiver's ability to capture signals
accurately.
Hence, as signal compensation is achieved through appropriate lane
equalization, apply lane equalization settings at both transmitter
and receiver which results in an increase in the PCIe signal strength.
While at it, modify the pcie-tegra194 driver to make use of the
common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The PCIe controller in rk3568 and rk3588 can operate in endpoint mode.
This endpoint mode support heavily leverages the existing code in
pcie-designware-ep.c.
Add support for endpoint mode to the existing pcie-dw-rockchip glue
driver.
[kwilczynski: squash with patch adding the PCI_ENDPOINT dependency]
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-10-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive PCI
drivers to use the newer symbol.
Link: https://lore.kernel.org/linux-pci/20230918-safeness-cornflake-62278bc3aaaa@wendy
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Add R-Car Gen4 PCIe controller for endpoint mode. This controller is based
on Synopsys DesignWare PCIe.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-14-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
Add R-Car Gen4 PCIe controller support for host mode.
This controller is based on Synopsys DesignWare PCIe. However, this
particular controller has a number of vendor-specific registers, and as
such, requires initialization code like mode setting and retraining and
so on.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-13-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
Sort Kconfig entries by vendor so they appear in alphabetical order in
menuconfig.
Link: https://lore.kernel.org/r/20230418174336.145585-7-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use "PCIe controller" consistently instead of "host bridge", "bus driver",
etc. Annotate with "(host mode)" or "(endpoint mode)" as needed.
Link: https://lore.kernel.org/r/20230418174336.145585-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add the "Amlogic" vendor name to the CONFIG_PCI_MESON Kconfig prompt to
match other PCIe drivers. Capitalize "Meson" to match other Meson Kconfig
prompts.
Link: https://lore.kernel.org/r/20230418174336.145585-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
|
|
pcie-kirin uses regmaps, and needs to pull them in; otherwise, with
CONFIG_PCIE_KIRIN=y and without CONFIG_REGMAP_MMIO pcie-kirin produces
a linker failure looking for __devm_regmap_init_mmio_clk().
Fixes: d19afe7be126 ("PCI: kirin: Use regmap for APB registers")
Link: https://lore.kernel.org/r/04636141da1d6d592174eefb56760511468d035d.1668410580.git.josh@joshtriplett.org
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
[lpieralisi@kernel.org: commit log and removed REGMAP select]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org # 5.16+
|
|
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...
|
|
i.MX PCIe is one dual mode PCIe controller.
Add i.MX PCIe EP mode support here, and split the PCIe modes to the Root
Complex mode and Endpoint mode.
Link: https://lore.kernel.org/r/1673847684-31893-12-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
a474d3fbe287 ("PCI/MSI: Get rid of PCI_MSI_IRQ_DOMAIN") removed
PCI_MSI_IRQ_DOMAIN and changed all references to refer to PCI_MSI instead.
ba6ed462dcf4 ("PCI: dwc: Add Baikal-T1 PCIe controller support")
independently added PCIE_BT1, depending on PCI_MSI_IRQ_DOMAIN.
Both commits appeared in v6.2-rc1, so the latter missed the conversion from
PCI_MSI_IRQ_DOMAIN to PCI_MSI. Update PCIE_BT1 to depend on PCI_MSI
instead.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20221215103452.23131-1-lukas.bulwahn@gmail.com
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Squash portdrv_{core,pci}.c into portdrv.c to ease maintenance and
make more things static.
- Make portdrv bind to Switch Ports that have AER. Previously, if
these Ports lacked MSI/MSI-X, portdrv failed to bind, which meant
the Ports couldn't be suspended to low-power states. AER on these
Ports doesn't use interrupts, and the AER driver doesn't need to
claim them.
- Assign PCI domain IDs using ida_alloc(), which makes host bridge
add/remove work better.
Resource management:
- To work better with recent BIOSes that use EfiMemoryMappedIO for
PCI host bridge apertures, remove those regions from the E820 map
(E820 entries normally prevent us from allocating BARs). In v5.19,
we added some quirks to disable E820 checking, but that's not very
maintainable. EfiMemoryMappedIO means the OS needs to map the
region for use by EFI runtime services; it shouldn't prevent OS
from using it.
PCIe native device hotplug:
- Build pciehp by default if USB4 is enabled, since Thunderbolt/USB4
PCIe tunneling depends on native PCIe hotplug.
- Enable Command Completed Interrupt only if supported to avoid user
confusion from lspci output that says this is enabled but not
supported.
- Prevent pciehp from binding to Switch Upstream Ports; this happened
because of interaction with acpiphp and caused devices below the
Upstream Port to disappear.
Power management:
- Convert AGP drivers to generic power management. We hope to remove
legacy power management from the PCI core eventually.
Virtualization:
- Fix pci_device_is_present(), which previously always returned
"false" for VFs, causing virtio hangs when unbinding the driver.
Miscellaneous:
- Convert drivers to gpiod API to prepare for dropping some legacy
code.
- Fix DOE fencepost error for the maximum data object length.
Baikal-T1 PCIe controller driver:
- Add driver and DT bindings.
Broadcom STB PCIe controller driver:
- Enable Multi-MSI.
- Delay 100ms after PERST# deassert to allow power and clocks to
stabilize.
- Configure Read Completion Boundary to 64 bytes.
Freescale i.MX6 PCIe controller driver:
- Initialize PHY before deasserting core reset to fix a regression in
v6.0 on boards where the PHY provides the reference.
- Fix imx6sx and imx8mq clock names in DT schema.
Intel VMD host bridge driver:
- Fix Secondary Bus Reset on VMD bridges, which allows reset of NVMe
SSDs in VT-d pass-through scenarios.
- Disable MSI remapping, which gets re-enabled by firmware during
suspend/resume.
MediaTek PCIe Gen3 controller driver:
- Add MT7986 and MT8195 support.
Qualcomm PCIe controller driver:
- Add SC8280XP/SA8540P basic interconnect support.
Rockchip DesignWare PCIe controller driver:
- Base DT schema on common Synopsys schema.
Synopsys DesignWare PCIe core:
- Collect DT items shared between Root Port and Endpoint (PERST GPIO,
PHY info, clocks, resets, link speed, number of lanes, number of
iATU windows, interrupt info, etc) to snps,dw-pcie-common.yaml.
- Add dma-ranges support for Root Ports and Endpoints.
- Consolidate DT resource retrieval for "dbi", "dbi2", "atu", etc. to
reduce code duplication.
- Add generic names for clocks and resets to encourage more
consistent naming across drivers using DesignWare IP.
- Stop advertising PTM Responder role for Endpoints, which aren't
allowed to be responders.
TI J721E PCIe driver:
- Add j721s2 host mode ID to DT schema.
- Add interrupt properties to DT schema.
Toshiba Visconti PCIe controller driver:
- Fix interrupts array max constraints in DT schema"
* tag 'pci-v6.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (95 commits)
x86/PCI: Use pr_info() when possible
x86/PCI: Fix log message typo
x86/PCI: Tidy E820 removal messages
PCI: Skip allocate_resource() if too little space available
efi/x86: Remove EfiMemoryMappedIO from E820 map
PCI/portdrv: Allow AER service only for Root Ports & RCECs
PCI: xilinx-nwl: Fix coding style violations
PCI: mvebu: Switch to using gpiod API
PCI: pciehp: Enable Command Completed Interrupt only if supported
PCI: aardvark: Switch to using devm_gpiod_get_optional()
dt-bindings: PCI: mediatek-gen3: add support for mt7986
dt-bindings: PCI: mediatek-gen3: add SoC based clock config
dt-bindings: PCI: qcom: Allow 'dma-coherent' property
PCI: mt7621: Add sentinel to quirks table
PCI: vmd: Fix secondary bus reset for Intel bridges
PCI: endpoint: pci-epf-vntb: Fix sparse ntb->reg build warning
PCI: endpoint: pci-epf-vntb: Fix sparse build warning for epf_db
PCI: endpoint: pci-epf-vntb: Replace hardcoded 4 with sizeof(u32)
PCI: endpoint: pci-epf-vntb: Remove unused epf_db_phy struct member
PCI: endpoint: pci-epf-vntb: Fix call pci_epc_mem_free_addr() in error path
...
|
Bjorn Helgaas
Wilfred Mallawa
Marek Vasut
Arnd Bergmann
Sherry Sun
Xincheng Zhang
Senchuan Zhang
Neil Armstrong
Randolph Lin
Andy Shevchenko
Sascha Hauer
Vidya Sagar
Vincent Guittot
Alex Elder
Siddharth Vadapalli
Christian Bruel
Krishna Chaitanya Chundru
Qiang Yu
Inochi Amaoto
Nam Cao
Mayank Rana
Thippeswamy Havalige
Shradha Todi
Shashank Babu Chinta Venkata
Niklas Cassel
Conor Dooley
Yoshihiro Shimoda
Josh Triplett
Linus Torvalds
Richard Zhu
Lukas Bulwahn