| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This header file is private to the Intel IOMMU driver. Move it to the
driver folder.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lore.kernel.org/r/20220514014322.2927339-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The exported symbol intel_iommu_gfx_mapped is not used anywhere in the
tree. Remove it to avoid dead code.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lore.kernel.org/r/20220514014322.2927339-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The IOMMU driver shares the pasid table for PCI alias devices. When the
RID2PASID entry of the shared pasid table has been filled by the first
device, the subsequent device will encounter the "DMAR: Setup RID2PASID
failed" failure as the pasid entry has already been marked as present.
As the result, the IOMMU probing process will be aborted.
On the contrary, when any alias device is hot-removed from the system,
for example, by writing to /sys/bus/pci/devices/.../remove, the shared
RID2PASID will be cleared without any notifications to other devices.
As the result, any DMAs from those rest devices are blocked.
Sharing pasid table among PCI alias devices could save two memory pages
for devices underneath the PCIe-to-PCI bridges. Anyway, considering that
those devices are rare on modern platforms that support VT-d in scalable
mode and the saved memory is negligible, it's reasonable to remove this
part of immature code to make the driver feasible and stable.
Fixes: ef848b7e5a6a0 ("iommu/vt-d: Setup pasid entry for RID2PASID support")
Reported-by: Chenyi Qiang <chenyi.qiang@intel.com>
Reported-by: Ethan Zhao <haifeng.zhao@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Ethan Zhao <haifeng.zhao@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220623065720.727849-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20220625133430.2200315-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
As domain->force_snooping only impacts the devices attached with the
domain, there's no need to check against all IOMMU units. On the other
hand, force_snooping could be set on a domain no matter whether it has
been attached or not, and once set it is an immutable flag. If no
device attached, the operation always succeeds. Then this empty domain
can be only attached to a device of which the IOMMU supports snoop
control.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20220508123525.1973626-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20220510023407.2759143-7-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
IOMMU_CACHE means "normal DMA to this iommu_domain's IOVA should be cache
coherent" and is used by the DMA API. The definition allows for special
non-coherent DMA to exist - ie processing of the no-snoop flag in PCIe
TLPs - so long as this behavior is opt-in by the device driver.
The flag is mainly used by the DMA API to synchronize the IOMMU setting
with the expected cache behavior of the DMA master. eg based on
dev_is_dma_coherent() in some case.
For Intel IOMMU IOMMU_CACHE was redefined to mean 'force all DMA to be
cache coherent' which has the practical effect of causing the IOMMU to
ignore the no-snoop bit in a PCIe TLP.
x86 platforms are always IOMMU_CACHE, so Intel should ignore this flag.
Instead use the new domain op enforce_cache_coherency() which causes every
IOPTE created in the domain to have the no-snoop blocking behavior.
Reconfigure VFIO to always use IOMMU_CACHE and call
enforce_cache_coherency() to operate the special Intel behavior.
Remove the IOMMU_CACHE test from Intel IOMMU.
Ultimately VFIO plumbs the result of enforce_cache_coherency() back into
the x86 platform code through kvm_arch_register_noncoherent_dma() which
controls if the WBINVD instruction is available in the guest. No other
archs implement kvm_arch_register_noncoherent_dma() nor are there any
other known consumers of VFIO_DMA_CC_IOMMU that might be affected by the
user visible result change on non-x86 archs.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/2-v3-2cf356649677+a32-intel_no_snoop_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This new mechanism will replace using IOMMU_CAP_CACHE_COHERENCY and
IOMMU_CACHE to control the no-snoop blocking behavior of the IOMMU.
Currently only Intel and AMD IOMMUs are known to support this
feature. They both implement it as an IOPTE bit, that when set, will cause
PCIe TLPs to that IOVA with the no-snoop bit set to be treated as though
the no-snoop bit was clear.
The new API is triggered by calling enforce_cache_coherency() before
mapping any IOVA to the domain which globally switches on no-snoop
blocking. This allows other implementations that might block no-snoop
globally and outside the IOPTE - AMD also documents such a HW capability.
Leave AMD out of sync with Intel and have it block no-snoop even for
in-kernel users. This can be trivially resolved in a follow up patch.
Only VFIO needs to call this API because it does not have detailed control
over the device to avoid requesting no-snoop behavior at the device
level. Other places using domains with real kernel drivers should simply
avoid asking their devices to set the no-snoop bit.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/1-v3-2cf356649677+a32-intel_no_snoop_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Starting from Intel VT-d v3.2, Intel platform BIOS can provide additional
SATC table structure. SATC table includes a list of SoC integrated devices
that support ATC (Address translation cache).
Enabling ATC (via ATS capability) can be a functional requirement for SATC
device operation or optional to enhance device performance/functionality.
This is determined by the bit of ATC_REQUIRED in SATC table. When IOMMU is
working in scalable mode, software chooses to always enable ATS for every
device in SATC table because Intel SoC devices in SATC table are trusted to
use ATS.
On the other hand, if IOMMU is in legacy mode, ATS of SATC capable devices
can work transparently to software and be automatically enabled by IOMMU
hardware. As the result, there is no need for software to enable ATS on
these devices.
This also removes dmar_find_matched_atsr_unit() helper as it becomes dead
code now.
Signed-off-by: Yian Chen <yian.chen@intel.com>
Link: https://lore.kernel.org/r/20220222185416.1722611-1-yian.chen@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20220301020159.633356-13-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Compiler is not happy about hidden declaration of intel_iommu_ops.
.../iommu.c:414:24: warning: symbol 'intel_iommu_ops' was not declared. Should it be static?
Move declaration to header file to make compiler happy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220207141240.8253-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20220301020159.633356-10-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Allocate and set the per-device iommu private data during iommu device
probe. This makes the per-device iommu private data always available
during iommu_probe_device() and iommu_release_device(). With this changed,
the dummy DEFER_DEVICE_DOMAIN_INFO pointer could be removed. The wrappers
for getting the private data and domain are also cleaned.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20220214025704.3184654-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20220301020159.633356-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The "domains" field of the intel_iommu structure keeps the mapping of
domain_id to dmar_domain. This information is not used anywhere. Remove
and cleanup it to avoid unnecessary memory consumption.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20220214025704.3184654-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20220301020159.633356-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The aux-domain related callbacks are not called in the tree. Remove them
to avoid dead code.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20220216025249.3459465-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The guest pasid related callbacks are not called in the tree. Remove them
to avoid dead code.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20220216025249.3459465-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The __domain_mapping() always removes the pages in the range from
'iov_pfn' to 'end_pfn', but the 'end_pfn' is always the last pfn
of the range that the caller wants to map.
This would introduce too many duplicated removing and leads the
map operation take too long, for example:
Map iova=0x100000,nr_pages=0x7d61800
iov_pfn: 0x100000, end_pfn: 0x7e617ff
iov_pfn: 0x140000, end_pfn: 0x7e617ff
iov_pfn: 0x180000, end_pfn: 0x7e617ff
iov_pfn: 0x1c0000, end_pfn: 0x7e617ff
iov_pfn: 0x200000, end_pfn: 0x7e617ff
...
it takes about 50ms in total.
We can reduce the cost by recalculate the 'end_pfn' and limit it
to the boundary of the end of this pte page.
Map iova=0x100000,nr_pages=0x7d61800
iov_pfn: 0x100000, end_pfn: 0x13ffff
iov_pfn: 0x140000, end_pfn: 0x17ffff
iov_pfn: 0x180000, end_pfn: 0x1bffff
iov_pfn: 0x1c0000, end_pfn: 0x1fffff
iov_pfn: 0x200000, end_pfn: 0x23ffff
...
it only need 9ms now.
This also removes a meaningless BUG_ON() in __domain_mapping().
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Tested-by: Liujunjie <liujunjie23@huawei.com>
Link: https://lore.kernel.org/r/20211008000433.1115-1-longpeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-10-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The first_pte_in_page() returns true or false, so let's convert its
return type to bool. In addition, use 'IS_ALIGNED' to make the
code more readable and neater.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Link: https://lore.kernel.org/r/20211008000433.1115-1-longpeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-9-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The iommu_domain data structure already has the "type" field to keep the
type of a domain. It's unnecessary to have the DOMAIN_FLAG_STATIC_IDENTITY
flag in the vt-d implementation. This cleans it up with no functionality
change.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210926114535.923263-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The VT-d spec Revision 3.3 updated the virtual command registers, virtual
command opcode B register, virtual command response register and virtual
command capability register (Section 10.4.43, 10.4.44, 10.4.45, 10.4.46).
This updates the virtual command interface implementation in the Intel
IOMMU driver accordingly.
Fixes: 24f27d32ab6b7 ("iommu/vt-d: Enlightened PASID allocation")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Sanjay Kumar <sanjay.k.kumar@intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210713042649.3547403-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210818134852.1847070-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Avoid below checkpatch warning.
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
+ unsigned iommu_refcnt[DMAR_UNITS_SUPPORTED];
Fixes: 29a27719abaa ("iommu/vt-d: Replace iommu_bmp with a refcount")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210530075053.264218-1-parav@nvidia.com
Link: https://lore.kernel.org/r/20210610020115.1637656-23-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
DMAR domain uses per DMAR refcount. It is indexed by iommu seq_id.
Older iommu_count is only incremented and decremented but no decisions
are taken based on this refcount. This is not of much use.
Hence, remove iommu_count and further simplify domain_detach_iommu()
by returning void.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210530075053.264218-1-parav@nvidia.com
Link: https://lore.kernel.org/r/20210610020115.1637656-21-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
IOTLB device presence, iommu coherency and snooping are boolean
capabilities. Use them as bits and keep them adjacent.
Structure layout before the reorg.
$ pahole -C dmar_domain drivers/iommu/intel/dmar.o
struct dmar_domain {
int nid; /* 0 4 */
unsigned int iommu_refcnt[128]; /* 4 512 */
/* --- cacheline 8 boundary (512 bytes) was 4 bytes ago --- */
u16 iommu_did[128]; /* 516 256 */
/* --- cacheline 12 boundary (768 bytes) was 4 bytes ago --- */
bool has_iotlb_device; /* 772 1 */
/* XXX 3 bytes hole, try to pack */
struct list_head devices; /* 776 16 */
struct list_head subdevices; /* 792 16 */
struct iova_domain iovad __attribute__((__aligned__(8)));
/* 808 2320 */
/* --- cacheline 48 boundary (3072 bytes) was 56 bytes ago --- */
struct dma_pte * pgd; /* 3128 8 */
/* --- cacheline 49 boundary (3136 bytes) --- */
int gaw; /* 3136 4 */
int agaw; /* 3140 4 */
int flags; /* 3144 4 */
int iommu_coherency; /* 3148 4 */
int iommu_snooping; /* 3152 4 */
int iommu_count; /* 3156 4 */
int iommu_superpage; /* 3160 4 */
/* XXX 4 bytes hole, try to pack */
u64 max_addr; /* 3168 8 */
u32 default_pasid; /* 3176 4 */
/* XXX 4 bytes hole, try to pack */
struct iommu_domain domain; /* 3184 72 */
/* size: 3256, cachelines: 51, members: 18 */
/* sum members: 3245, holes: 3, sum holes: 11 */
/* forced alignments: 1 */
/* last cacheline: 56 bytes */
} __attribute__((__aligned__(8)));
After arranging it for natural padding and to make flags as u8 bits, it
saves 8 bytes for the struct.
struct dmar_domain {
int nid; /* 0 4 */
unsigned int iommu_refcnt[128]; /* 4 512 */
/* --- cacheline 8 boundary (512 bytes) was 4 bytes ago --- */
u16 iommu_did[128]; /* 516 256 */
/* --- cacheline 12 boundary (768 bytes) was 4 bytes ago --- */
u8 has_iotlb_device:1; /* 772: 0 1 */
u8 iommu_coherency:1; /* 772: 1 1 */
u8 iommu_snooping:1; /* 772: 2 1 */
/* XXX 5 bits hole, try to pack */
/* XXX 3 bytes hole, try to pack */
struct list_head devices; /* 776 16 */
struct list_head subdevices; /* 792 16 */
struct iova_domain iovad __attribute__((__aligned__(8)));
/* 808 2320 */
/* --- cacheline 48 boundary (3072 bytes) was 56 bytes ago --- */
struct dma_pte * pgd; /* 3128 8 */
/* --- cacheline 49 boundary (3136 bytes) --- */
int gaw; /* 3136 4 */
int agaw; /* 3140 4 */
int flags; /* 3144 4 */
int iommu_count; /* 3148 4 */
int iommu_superpage; /* 3152 4 */
/* XXX 4 bytes hole, try to pack */
u64 max_addr; /* 3160 8 */
u32 default_pasid; /* 3168 4 */
/* XXX 4 bytes hole, try to pack */
struct iommu_domain domain; /* 3176 72 */
/* size: 3248, cachelines: 51, members: 18 */
/* sum members: 3236, holes: 3, sum holes: 11 */
/* sum bitfield members: 3 bits, bit holes: 1, sum bit holes: 5 bits */
/* forced alignments: 1 */
/* last cacheline: 48 bytes */
} __attribute__((__aligned__(8)));
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210530075053.264218-1-parav@nvidia.com
Link: https://lore.kernel.org/r/20210610020115.1637656-20-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The execution time of some operations is very performance critical, such
as cache invalidation and PRQ processing time. This adds some common code
to monitor the execution time range of those operations. The interfaces
include enabling/disabling, checking status, updating sampling data and
providing a common string format for users.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210520031531.712333-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210610020115.1637656-14-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This adds a new trace event to track the page fault request report.
This event will provide almost all information defined in a page
request descriptor.
A sample output:
| prq_report: dmar0/0000:00:0a.0 seq# 1: rid=0x50 addr=0x559ef6f97 r---- pasid=0x2 index=0x1
| prq_report: dmar0/0000:00:0a.0 seq# 2: rid=0x50 addr=0x559ef6f9c rw--l pasid=0x2 index=0x1
| prq_report: dmar0/0000:00:0a.0 seq# 3: rid=0x50 addr=0x559ef6f98 r---- pasid=0x2 index=0x1
| prq_report: dmar0/0000:00:0a.0 seq# 4: rid=0x50 addr=0x559ef6f9d rw--l pasid=0x2 index=0x1
| prq_report: dmar0/0000:00:0a.0 seq# 5: rid=0x50 addr=0x559ef6f99 r---- pasid=0x2 index=0x1
| prq_report: dmar0/0000:00:0a.0 seq# 6: rid=0x50 addr=0x559ef6f9e rw--l pasid=0x2 index=0x1
| prq_report: dmar0/0000:00:0a.0 seq# 7: rid=0x50 addr=0x559ef6f9a r---- pasid=0x2 index=0x1
| prq_report: dmar0/0000:00:0a.0 seq# 8: rid=0x50 addr=0x559ef6f9f rw--l pasid=0x2 index=0x1
This will be helpful for I/O page fault related debugging.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210520031531.712333-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210610020115.1637656-13-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This allocates and registers the iopf queue infrastructure for devices
which want to support IO page fault for SVA.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210520031531.712333-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210610020115.1637656-11-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Align the pasid alloc/free code with the generic helpers defined in the
iommu core. This also refactored the SVA binding code to improve the
readability.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210520031531.712333-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210610020115.1637656-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When the Intel IOMMU is operating in the scalable mode, some information
from the root and context table may be used to tag entries in the PASID
cache. Software should invalidate the PASID-cache when changing root or
context table entries.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: 7373a8cc38197 ("iommu/vt-d: Setup context and enable RID2PASID support")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320025415.641201-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The svm_dev_ops has never been referenced in the tree, and there's no
plan to have anything to use it. Remove it to make the code neat.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210323010600.678627-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When the invalidation queue errors are encountered, dump the information
logged by the VT-d hardware together with the pending queue invalidation
descriptors.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Guo Kaijie <Kaijie.Guo@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210318005340.187311-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Audit IOMMU Capability/Extended Capability and check if the IOMMUs have
the consistent value for features. Report out or scale to the lowest
supported when IOMMU features have incompatibility among IOMMUs.
Report out features when below features are mismatched:
- First Level 5 Level Paging Support (FL5LP)
- First Level 1 GByte Page Support (FL1GP)
- Read Draining (DRD)
- Write Draining (DWD)
- Page Selective Invalidation (PSI)
- Zero Length Read (ZLR)
- Caching Mode (CM)
- Protected High/Low-Memory Region (PHMR/PLMR)
- Required Write-Buffer Flushing (RWBF)
- Advanced Fault Logging (AFL)
- RID-PASID Support (RPS)
- Scalable Mode Page Walk Coherency (SMPWC)
- First Level Translation Support (FLTS)
- Second Level Translation Support (SLTS)
- No Write Flag Support (NWFS)
- Second Level Accessed/Dirty Support (SLADS)
- Virtual Command Support (VCS)
- Scalable Mode Translation Support (SMTS)
- Device TLB Invalidation Throttle (DIT)
- Page Drain Support (PDS)
- Process Address Space ID Support (PASID)
- Extended Accessed Flag Support (EAFS)
- Supervisor Request Support (SRS)
- Execute Request Support (ERS)
- Page Request Support (PRS)
- Nested Translation Support (NEST)
- Snoop Control (SC)
- Pass Through (PT)
- Device TLB Support (DT)
- Queued Invalidation (QI)
- Page walk Coherency (C)
Set capability to the lowest supported when below features are mismatched:
- Maximum Address Mask Value (MAMV)
- Number of Fault Recording Registers (NFR)
- Second Level Large Page Support (SLLPS)
- Fault Recording Offset (FRO)
- Maximum Guest Address Width (MGAW)
- Supported Adjusted Guest Address Width (SAGAW)
- Number of Domains supported (NDOMS)
- Pasid Size Supported (PSS)
- Maximum Handle Mask Value (MHMV)
- IOTLB Register Offset (IRO)
Signed-off-by: Kyung Min Park <kyung.min.park@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210130184452.31711-1-kyung.min.park@intel.com
Link: https://lore.kernel.org/r/20210204014401.2846425-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Fix misspellings of "physical".
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/linux-iommu/20210126211738.2920789-1-helgaas@kernel.org
Link: https://lore.kernel.org/r/20210204014401.2846425-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The Access/Dirty bits in the first level page table entry will be set
whenever a page table entry was used for address translation or write
permission was successfully translated. This is always true when using
the first-level page table for kernel IOVA. Instead of wasting hardware
cycles to update the certain bits, it's better to set them up at the
beginning.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210115004202.953965-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The aux-domain attach/detach are not tracked, some data structures might
be used after free. This causes general protection faults when multiple
subdevices are created and assigned to a same guest machine:
| general protection fault, probably for non-canonical address 0xdead000000000100: 0000 [#1] SMP NOPTI
| RIP: 0010:intel_iommu_aux_detach_device+0x12a/0x1f0
| [...]
| Call Trace:
| iommu_aux_detach_device+0x24/0x70
| vfio_mdev_detach_domain+0x3b/0x60
| ? vfio_mdev_set_domain+0x50/0x50
| iommu_group_for_each_dev+0x4f/0x80
| vfio_iommu_detach_group.isra.0+0x22/0x30
| vfio_iommu_type1_detach_group.cold+0x71/0x211
| ? find_exported_symbol_in_section+0x4a/0xd0
| ? each_symbol_section+0x28/0x50
| __vfio_group_unset_container+0x4d/0x150
| vfio_group_try_dissolve_container+0x25/0x30
| vfio_group_put_external_user+0x13/0x20
| kvm_vfio_group_put_external_user+0x27/0x40 [kvm]
| kvm_vfio_destroy+0x45/0xb0 [kvm]
| kvm_put_kvm+0x1bb/0x2e0 [kvm]
| kvm_vm_release+0x22/0x30 [kvm]
| __fput+0xcc/0x260
| ____fput+0xe/0x10
| task_work_run+0x8f/0xb0
| do_exit+0x358/0xaf0
| ? wake_up_state+0x10/0x20
| ? signal_wake_up_state+0x1a/0x30
| do_group_exit+0x47/0xb0
| __x64_sys_exit_group+0x18/0x20
| do_syscall_64+0x57/0x1d0
| entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix the crash by tracking the subdevices when attaching and detaching
aux-domains.
Fixes: 67b8e02b5e76 ("iommu/vt-d: Aux-domain specific domain attach/detach")
Co-developed-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1609949037-25291-3-git-send-email-yi.l.liu@intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
'struct intel_svm' is shared by all devices bound to a give process,
but records only a single pointer to a 'struct intel_iommu'. Consequently,
cache invalidations may only be applied to a single DMAR unit, and are
erroneously skipped for the other devices.
In preparation for fixing this, rework the structures so that the iommu
pointer resides in 'struct intel_svm_dev', allowing 'struct intel_svm'
to track them in its device list.
Fixes: 1c4f88b7f1f9 ("iommu/vt-d: Shared virtual address in scalable mode")
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Raj Ashok <ashok.raj@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Reported-by: Guo Kaijie <Kaijie.Guo@intel.com>
Reported-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Guo Kaijie <Kaijie.Guo@intel.com>
Signed-off-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Tested-by: Guo Kaijie <Kaijie.Guo@intel.com>
Cc: stable@vger.kernel.org # v5.0+
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1609949037-25291-2-git-send-email-yi.l.liu@intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
"intel_iommu=off" command line is used to disable iommu but iommu is force
enabled in a tboot system for security reason.
However for better performance on high speed network device, a new option
"intel_iommu=tboot_noforce" is introduced to disable the force on.
By default kernel should panic if iommu init fail in tboot for security
reason, but it's unnecessory if we use "intel_iommu=tboot_noforce,off".
Fix the code setting force_on and move intel_iommu_tboot_noforce
from tboot code to intel iommu code.
Fixes: 7304e8f28bb2 ("iommu/vt-d: Correctly disable Intel IOMMU force on")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Tested-by: Lukasz Hawrylko <lukasz.hawrylko@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201110071908.3133-1-zhenzhong.duan@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Pull iommu updates from Joerg Roedel:
- ARM-SMMU Updates from Will:
- Continued SVM enablement, where page-table is shared with CPU
- Groundwork to support integrated SMMU with Adreno GPU
- Allow disabling of MSI-based polling on the kernel command-line
- Minor driver fixes and cleanups (octal permissions, error
messages, ...)
- Secure Nested Paging Support for AMD IOMMU. The IOMMU will fault when
a device tries DMA on memory owned by a guest. This needs new
fault-types as well as a rewrite of the IOMMU memory semaphore for
command completions.
- Allow broken Intel IOMMUs (wrong address widths reported) to still be
used for interrupt remapping.
- IOMMU UAPI updates for supporting vSVA, where the IOMMU can access
address spaces of processes running in a VM.
- Support for the MT8167 IOMMU in the Mediatek IOMMU driver.
- Device-tree updates for the Renesas driver to support r8a7742.
- Several smaller fixes and cleanups all over the place.
* tag 'iommu-updates-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (57 commits)
iommu/vt-d: Gracefully handle DMAR units with no supported address widths
iommu/vt-d: Check UAPI data processed by IOMMU core
iommu/uapi: Handle data and argsz filled by users
iommu/uapi: Rename uapi functions
iommu/uapi: Use named union for user data
iommu/uapi: Add argsz for user filled data
docs: IOMMU user API
iommu/qcom: add missing put_device() call in qcom_iommu_of_xlate()
iommu/arm-smmu-v3: Add SVA device feature
iommu/arm-smmu-v3: Check for SVA features
iommu/arm-smmu-v3: Seize private ASID
iommu/arm-smmu-v3: Share process page tables
iommu/arm-smmu-v3: Move definitions to a header
iommu/io-pgtable-arm: Move some definitions to a header
iommu/arm-smmu-v3: Ensure queue is read after updating prod pointer
iommu/amd: Re-purpose Exclusion range registers to support SNP CWWB
iommu/amd: Add support for RMP_PAGE_FAULT and RMP_HW_ERR
iommu/amd: Use 4K page for completion wait write-back semaphore
iommu/tegra-smmu: Allow to group clients in same swgroup
iommu/tegra-smmu: Fix iova->phys translation
...
|
|
Pull x86 irq updates from Thomas Gleixner:
"Surgery of the MSI interrupt handling to prepare the support of
upcoming devices which require non-PCI based MSI handling:
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which
allows to utilize the full functionality of hierarchical
irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the
irqdomain which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch
and let the last few users select it"
* tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
PCI: MSI: Fix Kconfig dependencies for PCI_MSI_ARCH_FALLBACKS
x86/apic/msi: Unbreak DMAR and HPET MSI
iommu/amd: Remove domain search for PCI/MSI
iommu/vt-d: Remove domain search for PCI/MSI[X]
x86/irq: Make most MSI ops XEN private
x86/irq: Cleanup the arch_*_msi_irqs() leftovers
PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable
x86/pci: Set default irq domain in pcibios_add_device()
iommm/amd: Store irq domain in struct device
iommm/vt-d: Store irq domain in struct device
x86/xen: Wrap XEN MSI management into irqdomain
irqdomain/msi: Allow to override msi_domain_alloc/free_irqs()
x86/xen: Consolidate XEN-MSI init
x86/xen: Rework MSI teardown
x86/xen: Make xen_msi_init() static and rename it to xen_hvm_msi_init()
PCI/MSI: Provide pci_dev_has_special_msi_domain() helper
PCI_vmd_Mark_VMD_irqdomain_with_DOMAIN_BUS_VMD_MSI
irqdomain/msi: Provide DOMAIN_BUS_VMD_MSI
x86/irq: Initialize PCI/MSI domain at PCI init time
x86/pci: Reducde #ifdeffery in PCI init code
...
|
|
"flags" passed to intel_svm_bind_mm() is a bit mask and should be
defined as "unsigned int" instead of "int".
Change its type to "unsigned int".
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/1600187413-163670-3-git-send-email-fenghua.yu@intel.com
|
|
PASID is defined as a few different types in iommu including "int",
"u32", and "unsigned int". To be consistent and to match with uapi
definitions, define PASID and its variations (e.g. max PASID) as "u32".
"u32" is also shorter and a little more explicit than "unsigned int".
No PASID type change in uapi although it defines PASID as __u64 in
some places.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/1600187413-163670-2-git-send-email-fenghua.yu@intel.com
|
|
As a first step to make X86 utilize the direct MSI irq domain operations
store the irq domain pointer in the device struct when a device is probed.
This is done from dmar_pci_bus_add_dev() because it has to work even when
DMA remapping is disabled. It only overrides the irqdomain of devices which
are handled by a regular PCI/MSI irq domain which protects PCI devices
behind special busses like VMD which have their own irq domain.
No functional change. It just avoids the redirection through
arch_*_msi_irqs() and allows the PCI/MSI core to directly invoke the irq
domain alloc/free functions instead of having to look up the irq domain for
every single MSI interupt.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112333.714566121@linutronix.de
|
|
Static analyzer is not happy about intel_iommu_gfx_mapped declaration:
.../drivers/iommu/intel/iommu.c:364:5: warning: symbol 'intel_iommu_gfx_mapped' was not declared. Should it be static?
Move its declaration to Intel IOMMU header file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200828161212.71294-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The VT-d spec requires (10.4.4 Global Command Register, TE field) that:
Hardware implementations supporting DMA draining must drain any in-flight
DMA read/write requests queued within the Root-Complex before completing
the translation enable command and reflecting the status of the command
through the TES field in the Global Status register.
Unfortunately, some integrated graphic devices fail to do so after some
kind of power state transition. As the result, the system might stuck in
iommu_disable_translation(), waiting for the completion of TE transition.
This provides a quirk list for those devices and skips TE disabling if
the qurik hits.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=208363
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=206571
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Koba Ko <koba.ko@canonical.com>
Tested-by: Jun Miao <jun.miao@windriver.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200723013437.2268-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
After page requests are handled, software must respond to the device
which raised the page request with the result. This is done through
the iommu ops.page_response if the request was reported to outside of
vendor iommu driver through iommu_report_device_fault(). This adds the
VT-d implementation of page_response ops.
Co-developed-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Co-developed-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200724014925.15523-12-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
It is refactored in two ways:
- Make it global so that it could be used in other files.
- Make bus/devfn optional so that callers could ignore these two returned
values when they only want to get the coresponding iommu pointer.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200724014925.15523-9-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Global pages support is removed from VT-d spec 3.0 for dev TLB
invalidation. This patch is to remove the bits for vSVA. Similar change
already made for the native SVA. See the link below.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/linux-iommu/20190830142919.GE11578@8bytes.org/T/
Link: https://lore.kernel.org/r/20200724014925.15523-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Set proper masks to avoid invalid input spillover to reserved bits.
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200724014925.15523-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When using first-level translation for IOVA, currently the U/S bit in the
page table is cleared which implies DMA requests with user privilege are
blocked. As the result, following error messages might be observed when
passing through a device to user level:
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Read] Request device [41:00.0] PASID 1 fault addr 7ecdcd000
[fault reason 129] SM: U/S set 0 for first-level translation
with user privilege
This fixes it by setting U/S bit in the first level page table and makes
IOVA over first level compatible with previous second-level translation.
Fixes: b802d070a52a1 ("iommu/vt-d: Use iova over first level")
Reported-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200622231345.29722-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Sub-devices of a real DMA device might exist on a separate segment than
the real DMA device and its IOMMU. These devices should still have a
valid device_domain_info, but the current dma alias model won't
allocate info for the subdevice.
This patch adds a segment member to struct device_domain_info and uses
the sub-device's BDF so that these sub-devices won't alias to other
devices.
Fixes: 2b0140c69637e ("iommu/vt-d: Use pci_real_dma_dev() for mapping")
Cc: stable@vger.kernel.org # v5.6+
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200527165617.297470-3-jonathan.derrick@intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When a PASID is stopped or terminated, there can be pending PRQs
(requests that haven't received responses) in remapping hardware.
This adds the interface to drain page requests and call it when a
PASID is terminated.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-16-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Current qi_submit_sync() only supports single invalidation descriptor
per submission and appends wait descriptor after each submission to
poll the hardware completion. This extends the qi_submit_sync() helper
to support multiple descriptors, and add an option so that the caller
could specify the Page-request Drain (PD) bit in the wait descriptor.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-13-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch is an initial step to replace Intel SVM code with the
following IOMMU SVA ops:
intel_svm_bind_mm() => iommu_sva_bind_device()
intel_svm_unbind_mm() => iommu_sva_unbind_device()
intel_svm_is_pasid_valid() => iommu_sva_get_pasid()
The features below will continue to work but are not included in this patch
in that they are handled mostly within the IOMMU subsystem.
- IO page fault
- mmu notifier
Consolidation of the above will come after merging generic IOMMU sva
code[1]. There should not be any changes needed for SVA users such as
accelerator device drivers during this time.
[1] http://jpbrucker.net/sva/
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-12-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Add a get_domain_info() helper to retrieve the valid per-device
iommu private data.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-10-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When VT-d driver runs in the guest, PASID allocation must be
performed via virtual command interface. This patch registers a
custom IOASID allocator which takes precedence over the default
XArray based allocator. The resulting IOASID allocation will always
come from the host. This ensures that PASID namespace is system-
wide.
Virtual command registers are used in the guest only, to prevent
vmexit cost, we cache the capability and store it during initialization.
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200516062101.29541-9-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
Lu Baolu
Jason Gunthorpe
Yian Chen
Andy Shevchenko
Longpeng(Mike)
Parav Pandit
Kyung Min Park
Bjorn Helgaas
Liu Yi L
Zhenzhong Duan
Linus Torvalds
Fenghua Yu
Thomas Gleixner
Jacob Pan
Jon Derrick