| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is no point in failing the tests when RTC is not present.
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Daniel Diaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Some problems with reading the RTC time may happen rarely, for example
while the RTC is updating. So read the RTC many times to catch these
problems. For example, a previous attempt for my
commit ea6fa4961aab ("rtc: mc146818-lib: fix RTC presence check")
was incorrect and would have triggered this selftest.
To avoid the risk of damaging the hardware, wait 11ms before consecutive
reads.
In rtc_time_to_timestamp I copied values manually instead of casting -
just to be on the safe side. The 11ms wait period was chosen so that it is
not a divisor of 1000ms.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The timeout setting for the rtc kselftest is currently 90 seconds. This
setting is used by the kselftest runner to stop running a test if it
takes longer than the assigned value.
However, two of the test cases inside rtc set alarms. These alarms are
set to the next beginning of the minute, so each of these test cases may
take up to, in the worst case, 60 seconds.
In order to allow for all test cases in rtc to run, even in the worst
case, when using the kselftest runner, the timeout value should be
increased to at least 120. Set it to 180, so there's some additional
slack.
Correct operation can be tested by running the following command right
after the start of a minute (low second count), and checking that all
test cases run:
./run_kselftest.sh -c rtc
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Add SPDX License Identifier to all .gitignore files.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 852c8cbf34d3 ("selftests/kselftest/runner.sh: Add 45 second
timeout per test") added a 45 second timeout for tests, and also added
a way for tests to customise the timeout via a settings file.
For example the ftrace tests take multiple minutes to run, so they
were given longer in commit b43e78f65b1d ("tracing/selftests: Turn off
timeout setting").
This works when the tests are run from the source tree. However if the
tests are installed with "make -C tools/testing/selftests install",
the settings files are not copied into the install directory. When the
tests are then run from the install directory the longer timeouts are
not applied and the tests timeout incorrectly.
So add the settings files to TEST_FILES of the appropriate Makefiles
to cause the settings files to be installed using the existing install
logic.
Fixes: 852c8cbf34d3 ("selftests/kselftest/runner.sh: Add 45 second timeout per test")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
While building selftests, the following errors were observed:
> tools/testing/selftests/timens'
> gcc -Wall -Werror -pthread -lrt -ldl timens.c -o tools/testing/selftests/timens/timens
> /usr/bin/ld: /tmp/ccGy5CST.o: in function `check_config_posix_timers':
> timens.c:(.text+0x65a): undefined reference to `timer_create'
> collect2: error: ld returned 1 exit status
Quoting commit 870f193d48c2 ("selftests: net: use LDLIBS instead of
LDFLAGS"):
The default Makefile rule looks like:
$(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS)
When linking is done by gcc itself, no issue, but when it needs to be passed
to proper ld, only LDLIBS follows and then ld cannot know what libs to link
with.
More detail:
https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html
LDFLAGS
Extra flags to give to compilers when they are supposed to invoke the linker,
‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable
instead.
LDLIBS
Library flags or names given to compilers when they are supposed to invoke the
linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to
LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS
variable.
While at here, correct other selftests, not only timens ones.
Reported-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Commit a745f7af3cbd ("selftests/harness: Add 30 second timeout per
test") solves the problem of kselftest_harness.h-using binary tests
possibly hanging forever. However, scripts and other binaries can still
hang forever. This adds a global timeout to each test script run.
To make this configurable (e.g. as needed in the "rtc" test case),
include a new per-test-directory "settings" file (similar to "config")
that can contain kselftest-specific settings. The first recognized field
is "timeout".
Additionally, this splits the reporting for timeouts into a specific
"TIMEOUT" not-ok (and adds exit code reporting in the remaining case).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
|
|
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uie_read is a commonly failing test that will block forever on buggy rtc
drivers. Shorten its timeout so it fails earlier. Also increase the timeout
for the two alarm test on a minute boundary.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Unfortunately, some RTC don't have a second resolution for alarm so also
test for alarm on a minute boundary.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
|
|
Return values for select are not checked properly and timeouts may not be
detected.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
|
|
Rework rtctest to use the test harness to better handle skipping tests
(e.g. when alarms are not available). Also, it now handles timeout so it
will not block expecting an alarm that never comes.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
|
|
Move the RTC tests out of the timers folder as they are mostly unrelated.
Keep rtcpie in timers as it only test hrtimers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
|
Alexandre Belloni
Mateusz Jończyk
Nícolas F. R. A. Prado
Masahiro Yamada
Michael Ellerman
Dmitry Safonov
Kees Cook
Linus Torvalds
Thomas Gleixner