| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
ASPEED device tree updates for 6.1
- New machines
* AMD's DaytonaX AST2600 BMC, for the amd64 server
* Ampre's Mt. Mitchell AST2600 BMC, for the AmpereOne arm64 server
- Fixes and updates for bletchley, mtjade, yosemitev2 and the ast2600-evb
* tag 'aspeed-6.1-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: ast2600-evb-a1: Add compatible
ARM: dts: aspeed: ast2600evb: Fix compatible string
ARM: dts: aspeed: ast2600-evb: Enable Quad SPI RX tranfers
ARM: dts: aspeed-g6: Enable more UART controllers
ARM: dts: aspeed: yosemitev2: Disable the EEPROM driver
ARM: dts: aspeed: Add AMD DaytonaX BMC
dt-bindings: arm: aspeed: document AMD DaytonaX
ARM: dts: aspeed: Yosemite V2: Enable OCP debug card
ARM: dts: aspeed: mtjade: Remove gpio-keys entries
ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC
dt-bindings: arm: aspeed: document Ampere Mt.Mitchell BMC compatibles
ARM: dts: aspeed: bletchley: Remove hdc1080 node
ARM: dts: aspeed: bletchley: Add USB debug card IPMB node
ARM: dts: aspeed: ast2600-evb: Update I2C devices
Link: https://lore.kernel.org/r/CACPK8Xepnci+f+7Pi1jtXod8Jmt+OnJYfDRENjiP-xDBQwFCVg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add initial version of device tree for the BMC in the AMD DaytonaX
platform.
AMD DaytonaX platform is a customer reference board (CRB) with an
Aspeed ast2500 BMC manufactured by AMD.
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220921210950.10568-3-aladyshev22@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
hardware reference platform with AmpereOne(TM) processor.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220817071539.176110-3-quan@os.amperecomputing.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Qualcomm ARM64 DTS updates for 6.1
Support for Samsung Galaxy E5, E7 and Grand Max is added, with support
for both 32-bit and 64-bit variants. The Samsung Galaxy S4 Mini Value
Edition gains magnetometer support.
MSM8996-based Xiaomi devices gains descriptions of the LPG-based LEDs.
On SA8295P ADP problems arising from regulators being switched into
low-power mode is worked around by removing this ability, for now.
The onboard USB Hub on SC7180 Trogdor is finally described and a few ADC
related updates are introduced.
On SC7280 support for the CPU and LLC bwmon instances are introduced.
Soundwire, audio codecs and sound introduced for a variety of boards.
Using required-opps the USB controllers votes for a minimum corner on
VDD_CX.
The onboard USB Hub Herobrine is described. A new board, the Google
Evoker is added, as is another revision of Herobrine Villager.
On SC8280XP the USB controllers are marked as wakeup-sources, to keep
them powered during suspend. The CRD has HID devices marked as
wakeup-sources to enable resuming the system. In addition to these
changes the alternative touchpad is introduced on the Lenovo ThinkPad
X13s.
SDM845 gains RPMh stats support and the LLCC BWMON is added. For SM6350
interconnect providers and GPI DMA is introduced. A description of the
PM7280b PMIC is added to Fairphone FP4 on SM7225.
With the multi-MSI support added in the PCIe controller, SM8250 gets all
its MSI interrupts added.
UFS ICE and the second SDHCI controller is introduced on SM8450. Support
for the Sony Xperia 1 IV is introduced.
Throughout a variety of platforms the TCSR mutex syscon is replaced with
the MMIO-based binding. TCSR nodes gained proper compatibles and halt
syscon nodes are split out from the mutex ranges.
A range of fixes to align with DT bindings are introduced. Among these
are the changes to the follow the TLMM binding and suffix pinctrl states
with -state and subnodes thereof with -pins, another is a number of
changes transitioning to use -gpios and introduction of proper parent
clock references in various clock providers.
* tag 'qcom-arm64-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (136 commits)
arm64: dts: qcom: sc7280: Add required-opps for USB
arm64: dts: qcom: sm8450: fix UFS PHY serdes size
arm64: dts: qcom: ipq8074: fix PCIe PHY serdes size
arm64: dts: qcom: sa8295p-adp: add missing gpio-ranges in PMIC GPIOs
arm64: dts: qcom: sa8295p-adp: add fallback compatible to PMIC GPIOs
arm64: dts: qcom: msm8996-xiaomi: align PMIC GPIO pin configuration with DT schema
arm64: dts: qcom: msm8994-msft-lumia-octagon: align resin node name with bindings
arm64: dts: qcom: pmi8994: add missing MPP compatible fallback
dt-bindings: pci: QCOM Add missing sc7280 aggre0, aggre1 clocks
arm64: dts: qcom: sc7280: Add missing aggre0, aggre1 clocks
arm64: dts: qcom: sc7280-villager: Adjust LTE SKUs
dt-bindings: arm: qcom: Adjust LTE SKUs for sc7280-villager
arm64: dts: qcom: sc7280-herobrine: Add nodes for onboard USB hub
arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub
arm64: dts: qcom: align SDHCI reg-names with DT schema
arm64: dts: qcom: sm8250: provide additional MSI interrupts
arm64: dts: qcom: msm8996: add #clock-cells and XO clock to the HDMI PHY node
arm64: dts: qcom: Use WCD9335 DT bindings
arm64: dts: qcom: msm8994: switch TCSR mutex to MMIO
arm64: dts: qcom: ipq6018: switch TCSR mutex to MMIO
...
Link: https://lore.kernel.org/r/20220921234854.1343238-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX device tree change for 6.1
- A series from Alexander Stein to add missing properties for i.MX6 SRAM.
- Drop 'interrupts' property when 'interrupts-extended' is present. This
fixes a dtbs_check warning with i.MX6 DT.
- Update device trees to use generic name 'dma-controller' for SDMA.
- A set of changes from Krzysztof Kozlowski to align SPI, LED and
gpio-keys node name with dtschema.
- A series of indentation and white-space cleanups from Marcel Ziswiler
to address various checkpatch warnings.
- Add DDR pinmux defines to VF610 DT header.
- A couple of changes from Peng Fan to update clock-names and add IPG
clock for i.MX7ULP LPI2C devices.
- Improve device tree structure for Kontron i.MX6UL/ULL based boards.
- A series of changes from Tim Harvey to add CAN regulator for Gateworks
i.MX6QDL boards.
- Various small and random board specific updates.
* tag 'imx-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (40 commits)
ARM: dts: imx6qdl-gw54xx: add CAN regulator
ARM: dts: imx6qdl-gw53xx: add CAN regulator
ARM: dts: imx6qdl-gw52xx: add CAN regulator
ARM: dts: imx: update sdma node name format
ARM: dts: imx6: skov: migrate to resistive-adc-touch
ARM: dts: imx6sx-udoo-neo: don't use multiple blank lines
ARM: dts: imx6sl: use tabs for code indent
ARM: dts: imx6sx: add missing properties for sram
ARM: dts: imx6sll: add missing properties for sram
ARM: dts: imx6sl: add missing properties for sram
ARM: dts: imx6qp: add missing properties for sram
ARM: dts: imx6dl: add missing properties for sram
ARM: dts: imx6q: add missing properties for sram
ARM: dts: imx7ulp: Add IPG clock for lpi2c
ARM: dts: imx7ulp: update the LPI2C clock-names
ARM: dts: vf610: ddr pinmux
ARM: dts: imx6qdl-dhcom: Move IPU iomux node from PDK2 to SoM file
ARM: dts: imx6ul-kontron: Add imx6ull-kontron-bl to Makefile
ARM: dts: imx6ul-kontron: Simplify devicetree structure
ARM: dts: vf610: align SPI node name with dtschema
...
Link: https://lore.kernel.org/r/20220918092806.2152700-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The SAMA5D3-EDS board is an Ethernet Development Platform allowing for
evaluating many Microchip ethernet switch and PHY products. Various
daughter cards can connect via an RGMII connector or an RMII connector.
The EDS board is not intended for stand-alone use and has no ethernet
capabilities when no daughter board is connected. As such, this device
tree is intended to be used with a DT overlay defining the add-on board.
To better ensure consistency, some items are defined here as a form of
documentation so that all add-on overlays will use the same terms.
Link: https://www.microchip.com/en-us/development-tool/SAMA5D3-ETHERNET-DEVELOPMENT-SYSTEM
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
[claudiu.beznea: s/gpio-inputs/gpio-keys in at91-sama5d3_eds.dts]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220909163022.13022-2-jerry.ray@microchip.com
|
|
After adding all necessary support for MSM8916 SMP/cpuidle without PSCI
on ARM32, build the Samsung Galaxy E5/E7/Grand Max device trees from the
arm64 tree together with the ARM32 include to allow booting this device on
ARM32.
The approach to include device tree files from other architectures is
inspired from e.g. the Raspberry Pi (bcm2711-rpi-4-b.dts) where this is
used to build the device tree for both ARM32 and ARM64.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724095413.14135-1-linmengbo0689@protonmail.com
|
|
Add basic support for pcb8290. It has 2 lan8814 phys(each phy is a
quad-port) on the external MDIO bus and no SFP ports.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220825065135.1075049-1-horatiu.vultur@microchip.com
|
|
The imx6ull-kontron-bl.dtb wasn't build as part of the
CONFIG_SOC_IMX6UL option. Add it to the list.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is no need in differentiating between the different SoM versions
that only differ in memory size, etc. It's much cleaner to simplify
the devicetrees and let them be more generic.
If necessary the bootloader will update the devicetree dynamically
to contain the correct size of the memory.
We also get rid of the N6xxx notation in the compatibles and file
names, as they are not really used anymore and often result in
confusion.
This is a breaking change, but the impact shouldn't be too big and it
makes usage and maintenance easier in the future.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull ARM new SoC support from Arnd Bergmann:
"This adds initial support for two SoC families that have been under
review for a while. In both cases, the origonal idea was to have a
minimally functional version, but we ended up leaving out the clk
drivers that are still under review and will be merged through the
corresponding subsystem tree.
The Nuvoton NPCM8xx is a 64-bit Baseboard Management Controller and
based on the 32-bit NPCM7xx family but is now getting added to
arch/arm64 as well.
Sunplus SP7021, also known as Plus1, is a general-purpose
System-in-Package design based on the 32-bit Cortex-A7 SoC on the main
chip, plus an I/O chip and memory in the same"
* tag 'arm-newsoc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
MAINTAINERS: rectify entry for ARM/NUVOTON NPCM ARCHITECTURE
arm64: defconfig: Add Nuvoton NPCM family support
arm64: dts: nuvoton: Add initial NPCM845 EVB device tree
arm64: dts: nuvoton: Add initial NPCM8XX device tree
arm64: npcm: Add support for Nuvoton NPCM8XX BMC SoC
dt-bindings: arm: npcm: Add nuvoton,npcm845 GCR compatible string
dt-bindings: arm: npcm: Add nuvoton,npcm845 compatible string
dt-bindings: arm: npcm: Add maintainer
reset: npcm: Add NPCM8XX support
dt-bindings: reset: npcm: Add support for NPCM8XX
reset: npcm: using syscon instead of device data
ARM: dts: nuvoton: add reset syscon property
dt-bindings: reset: npcm: add GCR syscon property
dt-binding: clk: npcm845: Add binding for Nuvoton NPCM8XX Clock
dt-bindings: watchdog: npcm: Add npcm845 compatible string
dt-bindings: timer: npcm: Add npcm845 compatible string
ARM: dts: Add Sunplus SP7021-Demo-V3 board device tree
ARM: sp7021_defconfig: Add Sunplus SP7021 defconfig
ARM: sunplus: Add initial support for Sunplus SP7021 SoC
irqchip: Add Sunplus SP7021 interrupt controller driver
...
|
|
AT91 DT for v5.20 #4
It contains one new LAN966 based board, namely pcb8309, a cleanup
on Makefile to sort alphabetically LAN966 entries and 2 cleanups
on bindings.
* tag 'at91-dt-5.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
dt-bindings: soc: microchip: use absolute path to other schema
dt-bindings: soc: microchip: drop quotes when not needed
ARM: dts: lan966x: keep lan966 entries alphabetically sorted
ARM: dts: lan966x: add support for pcb8309
dt-bindings: arm: at91: add lan966 pcb8309 board
Link: https://lore.kernel.org/r/20220727075749.2445000-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Keep LAN966 entries alphabetically sorted.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220726084931.1789855-1-claudiu.beznea@microchip.com
|
|
Add basic support for pcb8309. It is similar with pcb8291 with one big
difference that is having 2 SFP cages. Therefore it has 4 network ports.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220722131836.2377720-3-horatiu.vultur@microchip.com
|
|
The board is unmaintained and unused, according to Joel, so simply let's
remove it.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/all/CACPK8XfxXi8kQr+vxta8rD6SBgxLf_oBjAH0UkPBacQta552YQ@mail.gmail.com/
Link: https://lore.kernel.org/r/20220623072428.33697-1-krzysztof.kozlowski@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.20, please pull the following:
- Stefan drops the unnecessary "#address-cells" and "#size-cells"
properties from the DPI node of BCM283x
- Anand documents and adds support for the 63178 and 6858 SoCs
- William migrates the 63138 platform over to ARCH_BCMBCA and ensures
that it is documented within the BCMBCA Device Tree binding documents.
He updates the 47622 DTS to remove unnecessary PSCI properties, fix
the GIC nodes and some minor cosmetic changes. He finally adds support
for the 63158, 4912, 6846, 6855, 6756, 63146, 6856, 63148, 6813, 6318
SoCs.
- Peter, Nicolas and Stefan adds the necessary Device Tree nodes to the
BCM2711 (Raspberry Pi 4) DTS to enable the use of the V3D GPU on these
platforms.
- Christian adds support for the BCM53015 based Cisco Meraki MR26
Wi-Fi access point.
- Krzysztof updates the Broadcom platforms DTS to add a missing
whitespace between the property name and its value.
* tag 'arm-soc/for-5.20/devicetree' of https://github.com/Broadcom/stblinux: (35 commits)
ARM: dts: Add BCM63138 generic board dts
ARM: dts: update dts files for bcmbca SoC BCM63138
ARM: dts: Move BCM963138DVT board dts to ARCH_BCMBCA
dt-bindings: arm: add BCM63138 SoC
ARM: dts: bcm2711: Use proper compatible in PM/Watchdog node
ARM: dts: bcm2835/bcm2711: Introduce reg-names in watchdog node
dt-bindings: soc: bcm: bcm2835-pm: Add support for bcm2711
dt-bindings: soc: bcm: bcm2835-pm: Introduce reg-names
dt-bindings: soc: bcm: bcm2835-pm: Convert bindings to DT schema
ARM: dts: BCM5301X: Add DT for Meraki MR26
dt-bindings: ARM: add bindings for the Meraki MR26
dt-bindings: arm64: Add BCM6813 SoC
ARM: dts: Add DTS files for bcmbca SoC BCM63148
dt-bindings: arm: Add BCM63148 SoC
dt-bindings: arm64: Add BCM6856 SoC
dt-bindings: arm64: Add BCM63146 SoC
ARM: dts: broadcom: correct gpio-keys properties
ARM: dts: broadcom: align gpio-key node names with dtschema
ARM: dts: Add DTS files for bcmbca SoC BCM6756
dt-bindings: arm: Add BCM6756 SoC
...
Link: https://lore.kernel.org/r/20220711164451.3542127-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX device tree change for 5.20:
- A series from Alexander Stein to fix some i.MX6UL dt_binding_check
warnings.
- Replace deprecated 'enable-sdio-wakeup' property with 'wakeup-source'
for a couple of boards.
- A set of imx7-colibri device tree updates from Marcel Ziswiler to
improve devices Display, Touch, Ethernet and SD/MMC, and also adds
Toradex Iris carrier board.
- A few improvements on imx6qdl-colibri board, correct SGTL5000 MCLK
handling, simplify handling of inverted PWM backlight.
- A series from Max Krummenacher (and Oleksandr Suvorov) to improve the
existing i.MX6 Apalis carrier board device trees and adds a new device
tree for the Ixora V1.2 carrier board.
- Add USB dual-role switching using extcon for imx7-colibri board.
- Add SFP node for TA 2.1 devices for LayerScape SoCs.
- Other small and random updates on various boards.
* tag 'imx-dt-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (61 commits)
ARM: dts: layerscape: Add SFP node for TA 2.1 devices
ARM: dts: imx6qdl-prti6q.dtsi: Add applicable properties to usdhc3
ARM: dts: imx6q-bosch-acc: Replace 'enable-sdio-wakeup'
ARM: dts: imx7d-smegw01: Replace 'enable-sdio-wakeup'
ARM: dts: imx6q-apalis: Cleanup
ARM: dts: imx6q-apalis: backlight pwm: Adapt brightness steps
ARM: dts: imx6q-apalis: backlight pwm: Simplify inverted backlight
ARM: dts: imx6q-apalis: Add support for Toradex Ixora V1.2 carrier boards
ARM: dts: imx6q-apalis: Clean-up sd card support
ARM: dts: imx6q-apalis: Add adv7280 video input
ARM: dts: imx6q-apalis: Add ov5640 mipi csi camera
ARM: dts: imx6q-apalis: Disable stmpe touchscreen
ARM: dts: imx6q-apalis: Disable HDMI
ARM: dts: imx6q-apalis: Add LVDS panel support
ARM: dts: imx6q-apalis: move gpio-keys to SoM dtsi
ARM: dts: imx6q-apalis: Move Atmel MXT touch ctrl to SoM dtsi
ARM: dts: imx6q-apalis: Move pinmux groups to SoM dtsi
ARM: dts: imx6q-apalis: Move parallel rgb interface to SoM dtsi
ARM: dts: imx6q-apalis: Command pmic to standby for poweroff
ARM: dts: imx6q-apalis: Add gpio-line-names
...
Link: https://lore.kernel.org/r/20220709082951.15123-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add generic bcm963138.dts file.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Use CONFIG_ARCH_BCMBCA to build all the BCMBCA SoC dts and remove
CONFIG_ARCH_BCM_63XX from the makefile
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add the basic support for Sunplus SP7021-Demo-V3 board.
Signed-off-by: Qin Jian <qinjian@cqplus1.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
STM32 DT for v5.20, round 1
Highlights:
----------
- MCU:
-Fix whitespace coding style. No functional changes.
- MPU:
- General:
- Remove specific IPCC wakeup interrupt on STM32MP15.
- Enable OPTEE firmware and scmi support (clock/reset) on
STM32MP13. It allows to enable RCC clock driver.
- Add new pins configurations groups.
- DH boards:
- Add DHCOR based DRC Compact board. It embeds: 2xETH, 1xCAN,
uSD, USB, eMMC and SDIO wifi.
- Add ST MIPID02 bindings to AV96 (not enabled by default)
- OSD32:
- Correct vcc-supply for eeprom.
- fix missing internally connected voltage regulator (ldo3
supplied by vdd_ddr).
* tag 'stm32-dt-for-v5.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (25 commits)
ARM: dts: stm32: Add ST MIPID02 bindings to AV96
ARM: dts: stm32: Add alternate pinmux for RCC pin
ARM: dts: stm32: Add alternate pinmux for DCMI pins
ARM: dts: stm32: Add DHCOR based DRC Compact board
ARM: dts: stm32: Add alternate pinmux for UART5 pins
ARM: dts: stm32: Add alternate pinmux for UART4 pins
ARM: dts: stm32: Add alternate pinmux for UART3 pins
ARM: dts: stm32: Add alternate pinmux for SPI2 pins
ARM: dts: stm32: Add alternate pinmux for CAN1 pins
dt-bindings: arm: stm32: Add compatible string for DH electronics DHCOR DRC Compact
ARM: dts: stm32: Fix SPI2 pinmux pin comments on stm32mp15
ARM: dts: stm32: add optee reserved memory on stm32mp135f-dk
ARM: dts: stm32: add RCC on STM32MP13x SoC family
ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP13
dt-bindings: rcc: stm32: select the "secure" path for stm32mp13
ARM: dts: stm32: correct vcc-supply for eeprom on stm32mp15xx-osd32
ARM: dts: stm32: fix missing internally connected voltage regulator for OSD32MP1
ARM: dts: stm32: adjust whitespace around '=' on MCU boards
ARM: dts: stm32: Move DHCOR BUCK3 VDD 2V9 adjustment to 1V8 DTSI
ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151
...
Link: https://lore.kernel.org/r/a250f32b-f67c-2922-0748-e39dc791e95c@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
SoCFPGA dts updates for v5.20
- Clean up the Mercury++ AA1 dts
- Add support the Google Chameleon v3 board
- Add defined GIC interrupt type for Agilex ECC
- Fix coding style around Stratix10 QSPI dts entry
- Add support for Stratix10 SW Virtual platform
- Move clocks entry out of the Stratix10 soc node
* tag 'socfpga_dts_updates_for_v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: altera: socfpga_stratix10: move clocks out of soc node
arm64: dts: Add support for Stratix 10 Software Virtual Platform
dt-bindings: altera: document Stratix 10 SWVP compatibles
arm64: dts: altera: adjust whitespace around '='
arm64: dts: intel: socfpga_agilex: use defined GIC interrupt type for ECC
dt-bindings: altera: Add Chameleon v3 board
ARM: dts: socfpga: Add Google Chameleon v3 devicetree
ARM: dts: socfpga: Add atsha204a node to Mercury+ AA1 dts
ARM: dts: socfpga: Move sdmmc-ecc node to Arria 10 dts
ARM: dts: socfpga: Change Mercury+ AA1 dts to dtsi
Link: https://lore.kernel.org/r/20220626004437.1224820-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Nuvia has been acquired by Qualcomm and the vendor name 'nuvia' will
not be used anymore so rename aspeed-bmc-nuvia-dc-scm.dts to
aspeed-bmc-qcom-dc-scm-v1.dts and change 'nuvia' to 'qcom' as its vendor
name in the file.
Fixes: 7b46aa7c008d ("ARM: dts: aspeed: Add Nuvia DC-SCM BMC")
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220523175640.60155-1-quic_jaehyoo@quicinc.com
Link: https://lore.kernel.org/r/20220624070511.4070659-1-joel@jms.id.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM i2c
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.
Odd stuff:
- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
This causes the system to immediately shutdown! Looking at reported
"418 degree Celsius" suggests that this sensor is not working.
WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The Ixora V1.2 carrier board adds SW relevant new features compared to
the V1.1 version.
- An I2C EEPROM is added.
- The SD card slot got a switchable 3.3V supply.
- Pull ups on the SD card signals are not assembled to faciliate 1.8V
speed modes.
- The CAN transceivers got a switchable 3.3V supply.
Add a new device tree and, as the differences are so small rework the
device tree for V1.1 to include the V1.2 device tree and adjust as
needed.
Drop adding the toradex,apalis_imx6q-ixora to the dtb compatible to
adhere to the binding yaml document.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add DTS for ARMv7 based broadband SoC BCM63148. bcm63148.dtsi is the SoC
description DTS header and bcm963148.dts is a simple DTS file for
Broadcom BCM963148 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add DTS for ARMv7 based broadband SoC BCM6756. bcm6756.dtsi is the SoC
description DTS header and bcm96756.dts is a simple DTS file for
Broadcom BCM96756 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add DTS for ARMv7 based broadband SoC BCM6855. bcm6855.dtsi is the SoC
description DTS header and bcm96855.dts is a simple DTS file for
Broadcom BCM96855 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add devicetree for the Google Chameleon v3 board.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The Mercury+ AA1 is not a standalone board, rather it's a module
with an Arria 10 SoC. Remove status = "okay" and i2c aliases, as they
are routed to the base board and should be enabled from there.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add DTS for ARMv7 based broadband SoC BCM6846. bcm6846.dtsi is the
SoC description DTS header and bcm96846.dts is a simple DTS file for
Broadcom BCM96846 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add support for Toradex Iris, small form-factor Pico-ITX Colibri Arm
Computer Module family Carrier Board.
Additional details available at
https://www.toradex.com/products/carrier-board/iris-carrier-board
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add dts for ARMv7 based broadband SoC BCM6878. bcm6878.dtsi is the
SoC description dts header and bcm96878.dts is a simple dts file for
Broadcom BCM96878 Reference board that only enable the UART port.
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add dts for ARMv7 based broadband SoC BCM63178. bcm63178.dtsi is the
SoC description dts header and bcm963178.dts is a simple dts file for
Broadcom BCM963178 Reference board that only enable the UART port.
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
ASPEED device tree updates for 5.19
- New machine:
* Nuvia's DC-SCM BMC
- Enable AST2600 GFX, the BMC-driven graphics device
- Add a bunch of devices for the AST2600 EVB
- Updates to the AST2600 Bletchley machine
- Backwards compatible changes to support the new spi-mem based SPI NOR
driver
* tag 'aspeed-5.19-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: ast2600-evb: Enable GFX device
ARM: dts: aspeed: Add GFX node to AST2600
ARM: dts: aspeed: ast2600-evb: Enable virtual hub
ARM: dts: aspeed: ast2600-evb: Enable video engine
ARM: dts: aspeed: everest, rainier: Add power-ffs-sync-history GPIO
ARM: dts: aspeed: Add Nuvia DC-SCM BMC
ARM: dts: aspeed: bletchley: add sample averaging for ADM1278
ARM: dts: aspeed: bletchley: add eeprom node on each sled
ARM: dts: aspeed: bletchley: add pca9536 node on each sled
ARM: dts: aspeed: bletchley: update gpio0 line names
ARM: dts: aspeed: bletchley: Enable mdio0 bus
ARM: dts: aspeed: bletchley: switch spi2 driver to aspeed-smc
ARM: dts: aspeed: bletchley: enable ehci0 device node
ARM: dts: aspeed: Add USB2.0 device controller node
ARM: dts: aspeed-g4: Set spi-max-frequency for all flashes
ARM: dts: aspeed: Enable Dual SPI RX transfers
ARM: dts: aspeed: Adjust "reg" property of FMC/SPI controllers
ARM: dts: aspeed: ast2600-evb: Enable RX delay for MAC0/MAC1
Link: https://lore.kernel.org/r/CACPK8XfUmFxU8Y6C+aZ2+=dT7=fCfs2=2_aYqyRjoXCoeQaUWQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Patch series from Nick Hawkins:
"The GXP is the HPE BMC SoC that is used in the majority of HPE current
generation servers. Traditionally the asic will last multiple
generations of server before being replaced.
Info about SoC:
HPE GXP is the name of the HPE Soc. This SoC is used to implement many
BMC features at HPE. It supports ARMv7 architecture based on the Cortex
A9 core. It is capable of using an AXI bus to which a memory controller
is attached. It has multiple SPI interfaces to connect boot flash and
BIOS flash. It uses a 10/100/1000 MAC for network connectivity. It has
multiple i2c engines to drive connectivity with a host infrastructure.
The initial patches enable the watchdog and timer enabling the host to
be able to boot."
* hpe/gxp-soc:
MAINTAINERS: Introduce HPE GXP Architecture
ARM: dts: Introduce HPE GXP Device tree
dt-bindings: arm: hpe: add GXP Support
dt-bindings: timer: hpe,gxp-timer: Add HPE GXP Timer and Watchdog
clocksource/drivers/timer-gxp: Add HPE GXP Timer
watchdog: hpe-wdt: Introduce HPE GXP Watchdog
ARM: configs: multi_v7_defconfig: Add HPE GXP ARCH
ARM: hpe: Introduce the HPE GXP architecture
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add initial version of device tree for Nuvia DC-SCM BMC which is
equipped with Aspeed AST2600 BMC SoC.
Signed-off-by: Graeme Gregory <quic_ggregory@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Link: https://lore.kernel.org/r/20220325190247.468079-1-quic_jaehyoo@quicinc.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The HPE SoC is new to linux. A basic device tree layout with minimum
required for linux to boot including a timer and watchdog support has
been created.
The dts file is empty at this point but will be updated in subsequent
updates as board specific features are enabled.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
AT91 & LAN966 DT #1 for 5.19:
- at91: DT compliance updates to gic and dataflash nodes
- lan966: addition to many basic nodes for various peripherals
- lan966: Kontron KSwitch D10: support for this new board
and its network switch
* tag 'at91-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: kswitch-d10: enable networking
ARM: dts: lan966x: add switch node
ARM: dts: lan966x: add serdes node
ARM: dts: lan966x: add reset switch reset node
ARM: dts: lan966x: add MIIM nodes
ARM: dts: lan966x: add hwmon node
ARM: dts: lan966x: add basic Kontron KSwitch D10 support
ARM: dts: lan966x: add flexcom I2C nodes
ARM: dts: lan966x: add flexcom SPI nodes
ARM: dts: lan966x: add all flexcom usart nodes
ARM: dts: lan966x: add missing uart DMA channel
ARM: dts: lan966x: add sgpio node
ARM: dts: lan966x: swap dma channels for crypto node
ARM: dts: lan966x: rename pinctrl nodes
ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
ARM: dts: at91: use generic node name for dataflash
Link: https://lore.kernel.org/r/20220513162338.87717-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add basic support for the Kontron KSwitch D10 MMT. It comes in two
variants: "6G-2GS" which features 6 Gigabit copper ports and two SFP
cages and "8G" which features 6 Gigbabit copper ports (where two are
2.5G capable).
For now the following is supported and working:
- Kernel console
- SFP cages
- SPI
- SGPIO
- Watchdog
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
[claudiu.beznea: fixed conflict on Makefile]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220502224127.2604333-8-michael@walle.cc
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
|
|
i.MX ARM device tree update for 5.19:
- New board support: PHYTEC phyGATE-Tauri-S, TQ-Systems MBa6UL,
LS1021A IoT board, Toradex Iris and Aster carrier, i.MX7D SMEGW01,
i.MXRT1050 EVK, Bosch ACC board.
- A series from Alexander Stein to update i.MX51 based digi-connectcore
board, regarding to DMA of UART devices, PMIC voltages, USB
vbus-supply and usbphy.
- A series of changes from David Jander and Oleksij Rempel to remove
prototype specific deprecated code not used in production from
i.MX6Q/DL Vicut1 board, and unify Vicut1 and Victgo variants to reduce
maintaining overhead.
- Quite some changes from different people to update imx6ull-colibri board
on various aspects, touchscreen, device tree overlays, NAND BCH geometry,
GPIO line names, FEC phy-supply, etc.
- A couple of changes from Fabio Estevam to switch imx6dl-plybas and
imx6ul-kontron-n6x1x-s to use standard 'uart-has-rtscts' property.
- A couple of patches from Li Yang to update IFC device compatible and
node name for LayerScape SoCs.
- Disable USB host to work around boot issue on imx6qdl-udoo board.
- A series from Max Krummenacher to update Colibri i.MX6DL device trees,
drop dedicated v1.1 DT, disable add-on accessories, cleanups, etc.
- Various random and small updates on i.MX28 and i.MX6 boards.
* tag 'imx-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (77 commits)
ARM: dts: imx6ull-colibri: improve pinctrl node names
ARM: dts: imx6ull-colibri: move gpio-keys node to som dtsi
ARM: dts: imx6ull-colibri: add/update some comments
ARM: dts: imx6ull-colibri: fix nand bch geometry
ARM: dts: imx6ull-colibri: add support for toradex aster carrier boards
ARM: dts: imx6ull-colibri: add support for toradex iris carrier boards
ARM: dts: imx6ull-colibri: add gpio-line-names
ARM: dts: imx6ull-colibri: update device trees to support overlays
ARM: dts: imx6ull-colibri: update usdhc1 pixmux and signaling
ARM: dts: imx6ull-colibri: add touchscreen device nodes
ARM: dts: imx6ull-colibri: add phy-supply to fec
ARM: dts: imx6ull-colibri: change touch i2c parameters
ARM: dts: imx6ull-colibri: use pull-down for adc pins
ARM: dts: Add bosch acc board
ARM: dts: imx: Add i.MXRT1050-EVK support
ARM: dts: imx7d-smegw01: Add support for i.MX7D SMEGW01 board
ARM: dts: imx6qdl-udoo: Disable USB host to work around boot issues
ARM: dts: imx27: use new 'dma-channels' property
ARM: dts: imx6qdl-phytec: Add LED labels
ARM: dts: ls1021a: reduce the interrupt-map-mask
...
Link: https://lore.kernel.org/r/20220508033843.2773685-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Qualcomm ARM DT updates for v5.19
This contains a long overdue overhaul of the MSM8974 DeviceTrees,
aligning the style, structure and naming with what we've learned since
the introduction of this platform.
On top of this the Sony Rhine platform gained I2C masters, NFC and
pstore support and the Fairphone 2 gained touchscreen support.
For the new SDX65 platform reserved-memory nodes, rpmpd, SPMI, CPU
clocks, SDHCI controller, SMMU and TCSR mutex was added. As was the
initial DeviceTree for the related PMX65 PMIC.
MSM8226 gained VADC and RTC support and support for the ASUS ZenWatch 2
was added.
* tag 'qcom-dts-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (62 commits)
ARM: dts: qcom: msm8974-FP2: Add supplies for remoteprocs
ARM: dts: qcom: msm8974-FP2: Configure charger
ARM: dts: qcom: msm8974-FP2: Add support for touchscreen
ARM: dts: qcom: sdx55: Remove ipa interconnect node
ARM: dts: qcom: msm8974: Add missing license headers
ARM: dts: qcom: msm8974-FP2: Add mmc* aliases
ARM: dts: qcom: msm8974-FP2: We're msm8974pro
ARM: dts: qcom-msm8974*: Remove unnecessary include
ARM: dts: qcom-msm8974-rhine: Add pstore node
ARM: dts: qcom-msm8974-rhine: Add NFC and enable I2C hosts
ARM: dts: qcom-msm8974*: Clean up old GPIO declarations
ARM: dts: qcom-msm8974*: Consolidate I2C/UART/SDHCI
ARM: dts: qcom-msm8974*: Enable IMEM unconditionally
ARM: dts: qcom-msm8974: Sort and clean up nodes
ARM: dts: qcom-msm8974: Convert ADSP to a MMIO device
ARM: dts: qcom-msm8974pro-*: Use the 8974pro name in DT filenames
ARM: dts: qcom-msm8974pro: Use &labels
ARM: dts: qcom-msm8974-castor: Use &labels
ARM: dts: qcom-msm8974-{"hon","am"}ami: Commonize and modernize the DTs
ARM: dts: qcom-msm8974-klte: Use &labels
...
Link: https://lore.kernel.org/r/20220509172125.313259-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add support for Toradex Aster, small form-factor Colibri Arm
Computer Module family carrier board.
Aster Device Trees:
- imx6ull-colibri-aster.dtb
- imx6ull-colibri-emmc-aster.dtb
- imx6ull-colibri-wifi-aster.dtb
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for Toradex Iris, small form-factor Pico-ITX Colibri Arm
Computer Module family carrier boards.
Iris Device Trees:
- imx6ull-colibri-iris.dtb
- imx6ull-colibri-emmc-iris.dtb
- imx6ull-colibri-wifi-iris.dtb
Iris-V2 Device Trees:
- imx6ull-colibri-iris-v2.dtb
- imx6ull-colibri-emmc-iris-v2.dtb
- imx6ull-colibri-wifi-iris-v2.dtb
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add device tree for the Bosch ACC board, based on i.MX6 Dual.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The NXP i.MXRT1050 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 core.
The EVK provides 32 MB SDRAM, 64 MB Quad SPI flash, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
[Jesse: Add clock-parents, edma, usdhc, anatop, remove old pinctl]
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.19, please pull the following:
- Oleksij fixes the ethernet node name for the USB Ethernet adapter on
BCM283x (Raspberry Pi 1/2/3) platforms
- Kuldeep fixes the PL022 SPI controller clock names to conform to the
binding
- Rafal updates the various BCM5301X (Northstar) Device Tree include
files to be dtsschema conforming for pinctrl, NAND
- Arinc adds the Asus RT-AC88U binding, removes some unnecessary
properties of the Ethernet switch DT node, populates the correct PHY
interface for port 5 of the switch, adds support for fetching the MAC
address from the NVMEM provider and finally disables gmac0 on that
device which is unused
- Phil updates the Raspberry Pi 1/2/3 DTS files to have the latest gpio
line names conforming to the printed circuit board layout
- Krzysztof updates various Broadcom DTS files to have a conforming SPI
nor Device Tree node
- Takayoshi adds support for the Buffalo WZR-1166DHP/WZR-1166DHP2
wireless routers based on the BCM4708 SoC
- William adds support for the BCM47622 ARMv7 Broadband SoC and provides
a basic DTS to boot upstream Linux on such a system
* tag 'arm-soc/for-5.19/devicetree' of https://github.com/Broadcom/stblinux: (22 commits)
ARM: dts: BCM5301X: Add DT for WZR-1166DHP,DHP2
ARM: dts: add dts files for bcmbca soc 47622
dt-bindings: arm: add bcmbca device tree binding document
ARM: dts: bcm283x: Align ETH_CLK GPIO line name
ARM: dts: bcm283x: Remove gpio line name NC
ARM: dts: bcm2835-rpi-b: Fix GPIO line names
ARM: dts: bcm2837-rpi-3-b-plus: Fix GPIO line name of power LED
ARM: dts: bcm2837-rpi-cm3-io3: Fix GPIO line names for SMPS I2C
ARM: dts: bcm2835-rpi-zero-w: Fix GPIO line name for Wifi/BT
ARM: dts: BCM5301X: Disable gmac0 and enable port@8 on Asus RT-AC88U
ARM: dts: broadcom: align SPI NOR node name with dtschema
dt-bindings: arm: bcm: add bindings for Asus RT-AC88U
ARM: dts: BCM5301X: Fix compatible strings for BCM53012 and BCM53016 SoC
dt-bindings: arm: bcm: create new description for BCM53016
dt-bindings: arm: bcm: fix BCM53012 and BCM53016 SoC strings
ARM: dts: BCM5301X: Retrieve gmac1 MAC address from NVRAM on Asus RT-AC88U
ARM: dts: BCM5301X: Add rgmii to port@5 of Broadcom switch on Asus RT-AC88U
ARM: dts: BCM5301X: Remove cell properties from srab ports on Asus RT-AC88U
ARM: dts: BCM5301X: Fix DTC warning for NAND node
ARM: dts: BCM5301X: Update pin controller node name
...
Link: https://lore.kernel.org/r/20220504210942.1838248-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
STM32 DT for v5.19, round 1
Highlights:
----------
-MCU:
-Fix pinctrl node names to match with pinctrl yaml.
- MPU:
-General:
- Fix pinctrl node names to match with pinctrl yaml.
- Add Protonics boards support based on STM32MP151A SoC:
- PRTT1C - 10BaseT1L switch: mainly embeds a sja1105q switch with
TI and Micrel 10BaseT Phys and wifi support.
- PRTT1S - 10BaseT1L CO2 sensor board: mainly embeds I2C humidity
and CO2 sensors.
- PRTT1A - 10BaseT1L multi functional controller.
- ST boards:
- Add RTC support on stm32mp13.
- Add button and heartbit support on stm32mp13 DK board.
- Add a secure version of STM32MP15 ED1/EV1/DK1/DK2 boards based
on OP-TEE OS and SCMI protocol.
- DH boards:
- Use MCO2 to generate PHY clock and ETHRX clock in order to release
internal PLL for a better SD card usage.
- Add 1ms PHY post-reset on Avenger96 board to match with PHY
requirements.
* tag 'stm32-dt-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (24 commits)
ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
dt-bindings: arm: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15
dt-bindings: reset: stm32mp15: rename RST_SCMI define
dt-bindings: clock: stm32mp15: rename CK_SCMI define
dt-bindings: clock: stm32mp1: describes clocks if "st,stm32mp1-rcc-secure"
dt-bindings: rcc: Add optional external ethernet RX clock properties
ARM: dts: stm32: add UserPA13 button on stm32mp135f-dk
ARM: dts: stm32: add blue led (Linux heartbeat) on stm32mp135f-dk
ARM: dts: stm32: add EXTI interrupt-parent to pinctrl node on stm32mp131
ARM: dts: stm32: add support for Protonic PRTT1x boards
ARM: dts: stm32: stm32mp15-pinctrl: add spi1-1 pinmux group
dt-bindings: net: silabs,wfx: add prt,prtt1c-wfm200 antenna variant
dt-bindings: arm: stm32: Add compatible strings for Protonic T1L boards
dt-bindings: arm: stm32: correct blank lines
dt-bindings: arm: stm32: narrow DH STM32MP1 SoM boards
ARM: dts: stm32: enable RTC support on stm32mp135f-dk
ARM: dts: stm32: add RTC node on stm32mp131
ARM: dts: stm32: Fix PHY post-reset delay on Avenger96
ARM: dts: stm32: fix pinctrl node name warnings (MPU soc)
...
Link: https://lore.kernel.org/r/5818c943-882d-7e50-430d-ae3299a108ee@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add support for the i.MX7D SMEGW01 board.
This is a gateway board that supports the following peripherals:
- eMMC / SD card
- RTC
- USB modem
- Wifi via SDIO
- Dual Ethernet
- CAN
- Serial SRAM
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
Arnd Bergmann
Konstantin Aladyshev
Quan Nguyen
Jerry Ray
Lin, Meng-Bo
Horatiu Vultur
Frieder Schrempf
Linus Torvalds
Claudiu Beznea
Krzysztof Kozlowski
William Zhang
Qin Jian
Marek Vasut
Jae Hyun Yoo
Christian Lamparter
Max Krummenacher
Paweł Anikiel
Marcel Ziswiler
Anand Gore
Graeme Gregory
Nick Hawkins
Michael Walle
Denys Drozdov
Philip Oberfichtner
Giulio Benetti
Fabio Estevam