aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/broadcom/bgmac-bcma.c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2022-06-14net: bgmac: Fix an erroneous kfree() in bgmac_remove()Christophe JAILLET1-1/+0
'bgmac' is part of a managed resource allocated with bgmac_alloc(). It should not be freed explicitly. Remove the erroneous kfree() from the .remove() function. Fixes: 34a5102c3235 ("net: bgmac: allocate struct bgmac just once & don't copy it") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/a026153108dd21239036a032b95c25b5cece253b.1655153616.git.christophe.jaillet@wanadoo.fr Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-07ethernet: use of_get_ethdev_address()Jakub Kicinski1-1/+1
Use the new of_get_ethdev_address() helper for the cases where dev->dev_addr is passed in directly as the destination. @@ expression dev, np; @@ - of_get_mac_address(np, dev->dev_addr) + of_get_ethdev_address(np, dev) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-05net: bgmac: improve handling PHYRafał Miłecki1-12/+21
1. Use info from DT if available It allows describing for example a fixed link. It's more accurate than just guessing there may be one (depending on a chipset). 2. Verify PHY ID before trying to connect PHY PHY addr 0x1e (30) is special in Broadcom routers and means a switch connected as MDIO devices instead of a real PHY. Don't try connecting to it. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-02ethernet: use eth_hw_addr_set() instead of ether_addr_copy()Jakub Kicinski1-1/+1
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set(): @@ expression dev, np; @@ - ether_addr_copy(dev->dev_addr, np) + eth_hw_addr_set(dev, np) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-19net: bgmac-bcma: handle deferred probe error due to mac-addressChristian Lamparter1-0/+2
Due to the inclusion of nvmem handling into the mac-address getter function of_get_mac_address() by commit d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") it is now possible to get a -EPROBE_DEFER return code. Which did cause bgmac to assign a random ethernet address. This exact issue happened on my Meraki MR32. The nvmem provider is an EEPROM (at24c64) which gets instantiated once the module driver is loaded... This happens once the filesystem becomes available. With this patch, bgmac_probe() will propagate the -EPROBE_DEFER error. Then the driver subsystem will reschedule the probe at a later time. Cc: Petr Štetiar <ynezz@true.cz> Cc: Michael Walle <michael@walle.cc> Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-13of: net: pass the dst buffer to of_get_mac_address()Michael Walle1-6/+4
of_get_mac_address() returns a "const void*" pointer to a MAC address. Lately, support to fetch the MAC address by an NVMEM provider was added. But this will only work with platform devices. It will not work with PCI devices (e.g. of an integrated root complex) and esp. not with DSA ports. There is an of_* variant of the nvmem binding which works without devices. The returned data of a nvmem_cell_read() has to be freed after use. On the other hand the return of_get_mac_address() points to some static data without a lifetime. The trick for now, was to allocate a device resource managed buffer which is then returned. This will only work if we have an actual device. Change it, so that the caller of of_get_mac_address() has to supply a buffer where the MAC address is written to. Unfortunately, this will touch all drivers which use the of_get_mac_address(). Usually the code looks like: const char *addr; addr = of_get_mac_address(np); if (!IS_ERR(addr)) ether_addr_copy(ndev->dev_addr, addr); This can then be simply rewritten as: of_get_mac_address(np, ndev->dev_addr); Sometimes is_valid_ether_addr() is used to test the MAC address. of_get_mac_address() already makes sure, it just returns a valid MAC address. Thus we can just test its return code. But we have to be careful if there are still other sources for the MAC address before the of_get_mac_address(). In this case we have to keep the is_valid_ether_addr() call. The following coccinelle patch was used to convert common cases to the new style. Afterwards, I've manually gone over the drivers and fixed the return code variable: either used a new one or if one was already available use that. Mansour Moufid, thanks for that coccinelle patch! <spml> @a@ identifier x; expression y, z; @@ - x = of_get_mac_address(y); + x = of_get_mac_address(y, z); <... - ether_addr_copy(z, x); ...> @@ identifier a.x; @@ - if (<+... x ...+>) {} @@ identifier a.x; @@ if (<+... x ...+>) { ... } - else {} @@ identifier a.x; expression e; @@ - if (<+... x ...+>@e) - {} - else + if (!(e)) {...} @@ expression x, y, z; @@ - x = of_get_mac_address(y, z); + of_get_mac_address(y, z); ... when != x </spml> All drivers, except drivers/net/ethernet/aeroflex/greth.c, were compile-time tested. Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva1-1/+1
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2019-05-07net: ethernet: support of_get_mac_address new ERR_PTR errorPetr Štetiar1-1/+1
There was NVMEM support added to of_get_mac_address, so it could now return ERR_PTR encoded error values, so we need to adjust all current users of of_get_mac_address to this new fact. While at it, remove superfluous is_valid_ether_addr as the MAC address returned from of_get_mac_address is always valid and checked by is_valid_ether_addr anyway. Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-12net: bgmac: enable master mode for BCM54210E and B50212E PHYsRafał Miłecki1-1/+7
There are 4 very similar PHYs: 0x600d84a1: BCM54210E (rev B0) 0x600d84a2: BCM54210E (rev B1) 0x600d84a5: B50212E (rev B0) 0x600d84a6: B50212E (rev B1) that need setting master mode manually. It's because they run in slave mode by default with Automatic Slave/Master configuration disabled which can lead to unreliable connection with massive ping loss. So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY connected to the bgmac supported ethernet device. Telling PHY driver to setup PHY properly solves this issue. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16net: ethernet: bgmac: Allow MAC address to be specified in DTBSteve Lin1-16/+23
Allows the BCMA version of the bgmac driver to obtain MAC address from the device tree. If no MAC address is specified there, then the previous behavior (obtaining MAC address from SPROM) is used. Signed-off-by: Steve Lin <steven.lin1@broadcom.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Jon Mason <jon.mason@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-06net: ethernet: bgmac: unify code of the same familyJon Mason1-36/+28
BCM471X and BCM535X are of the same family (from what I can derive from internal documents). Group them into the case statement together, which results in more code reuse. Also, use existing helper variables to make the code a little more readable too. Signed-off-by: Jon Mason <jon.mason@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-17net: bgmac: store MAC address directly in netdev->dev_addrTobias Klauser1-1/+1
After commit 34a5102c3235 ("net: bgmac: allocate struct bgmac just once & don't copy it") the mac_addr member of struct bgmac is no longer necessary to pass the MAC address to bgmac_enet_probe(). Instead it can directly be stored in netdev->dev_addr. Also use eth_hw_addr_random() instead of eth_random_addr() in case a random MAC is nedded. This will make sure netdev->addr_assign_type will be properly set. Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Jon Mason <jon.mason@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-31net: bgmac: drop struct bcma_mdio we don't need anymoreRafał Miłecki1-1/+1
Adding struct bcma_mdio was a workaround for bcma code not having access to the struct bgmac used in the core code. Now we don't duplicate this struct we can just use it internally in bcma code. This simplifies code & allows access to all bgmac driver details from all places in bcma code. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-31net: bgmac: allocate struct bgmac just once & don't copy itRafał Miłecki1-3/+1
So far were were allocating struct bgmac in 3 places: platform code, bcma code and shared bgmac_enet_probe function. The reason for this was bgmac_enet_probe: 1) Requiring early-filled struct bgmac 2) Calling alloc_etherdev on its own in order to use netdev_priv later This solution got few drawbacks: 1) Was duplicating allocating code 2) Required copying early-filled struct 3) Resulted in platform/bcma code having access only to unused struct Solve this situation by simply extracting some probe code into the new bgmac_alloc function. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-07net: ethernet: bgmac: device tree phy enablementJon Mason1-0/+22
Change the bgmac driver to allow for phy's defined by the device tree Signed-off-by: Jon Mason <jon.mason@broadcom.com> Acked-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-1/+1
All three conflicts were cases of simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-18net: bgmac: support Ethernet core on BCM53573 SoCsRafał Miłecki1-1/+18
BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and can be found in two packages (versions): BCM53573 and BCM47189. It shares some code with the Northstar family, but also requires some new quirks. First of all there can be up to 2 Ethernet cores on this SoC. If that is the case, they are connected to two different switch ports allowing some more complex/optimized setups. It seems the second unit doesn't come fully configured and requires some IRQ quirk. Other than that only the first core is connected to the PHY. For the second one we have to register fixed PHY (similarly to the Northstar), otherwise generic PHY driver would get some invalid info. This has been successfully tested on Tenda AC9 (BCM47189B0). Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-18net: bgmac: fix reversed check for MII registration errorRafał Miłecki1-1/+1
It was failing on successful registration returning meaningless errors. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Fixes: 55954f3bfdac ("net: ethernet: bgmac: move BCMA MDIO Phy code into a separate file") Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-09net: ethernet: bgmac: Add platform device supportJon Mason1-0/+315
The bcma portion of the driver has been split off into a bcma specific driver. This has been mirrored for the platform driver. The last references to the bcma core struct have been changed into a generic function call. These function calls are wrappers to either the original bcma code or new platform functions that access the same areas via MMIO. This necessitated adding function pointers for both platform and bcma to hide which backend is being used from the generic bgmac code. Signed-off-by: Jon Mason <jon.mason@broadcom.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.